Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Is the T-harness I received with EVO-VWT1 wired incorrectly?

I installed an EVO-ALL using the EVO-VWT1 kit on a 2015 VW Jetta Push-to-Start. The EVO-ALL does not power up when I plug in the black datalink connector from the T-Harness. It powers and programs just fine on the Flashlink programmer connector. I think the T-harness connector is bad but would appreciate some guidance on how to address this.

0

2019 volkswagen golf R radio stays on

Hi, I installed a evo all standalone in a golf r everything works good only issue I noticed is the radio stays on after the remote times out or if we cancel the remote start , I tried the newest firmware as well as the one on the guide and no changes also tried enabling option d5 lock after start, is there any setting i can enable do to make radio turn off after the remote start shuts down or i have to wire the door pin? only thing that works at the moment is i press lock again and it turns off. thanks

0

VW Auto Stop-Start Error

2018 VW Tiguan, AT Std-Key, Analogue Cluster THAR-VW6, EVO-ALL FW 64.06 After installation of the THAR-VW6, the car has been giving an Auto Stop-Start Error. What option should be enabled to allow this option again.

0

2018 Tiguan will not start

2018 VW Tiguan, STD-Key, Not digital cluster, AT EVO-ALL firmware 64.06 THAR-VW6 Decrypted and programmed successfully, but when trying to remote start via lock lock lock from oem key, car turns on, but doesn't crank. Tested while in the car and the depress break light (shift lock) was still illuminated. I wired in the Yellow/Red Break Out to Black/Red VESCM (+)Foot Break correctly. Tested command start while in the car and depressing the break, works. Please assist.

0

2018 Tiguan will not start

2018 VW Tiguan, STD-Key, Not digital cluster, AT EVO-ALL firmware 64.06 THAR-VW6 Decrypted and programmed successfully, but when trying to remote start via lock lock lock from oem key, car turns on, but doesn't crank. Tested while in the car and the depress break light (shift lock) was still illuminated. I wired in the Yellow/Red Break Out to Black/Red VESCM (+)Foot Break correctly. Tested command start while in the car and depressing the break, works. Please assist.

0

issue with volkswagen golf r 2018

Hi guys, I have issue with install on golf r, I did a evo all stand alone everything was good but sometimes the car starts on the second or third attempt or it doesn't even start any idea what it could be? and also another issue sometimes the hazard light just keep flashing even after the car remote start stops. thanks

0

Please confirm which t-harness is required for 2019 Volkswagen Jetta

2019 VW Jetta. Push-to-start

Want to buy Evo-All for remote start using OEM key fob. 

    Which t-harness don’t need? THAR-VW 1.2.3. Or 6?Does this require sacrifice of a key?

0

VW Jetta 2015 - No Key even after Decrypt seems to have worked fine

I have installed a EVO ALL on a Jetta 2015 TDI (Push Start - Automatic).  I have the EVO ALL, THAR-VW1 and TB-VW installed as per instructions (I decided to skip the trunk release wiring as I didn't find the feature useful for me case).   The EVO All is programmed with Diesel Option enabled and it went through the Decryptor without any issues.  

When I press the 3 lock sequence,  the dash lights up (I had a previous problem that now brought me up to this point) but the dash says 'NO KEY'.   The car starts if I get the key in the car,  but not if the key is not in the car.   I was wondering what could be the problem.  The only item that I was wondering is that I reprogrammed (changed options) on the EVO ALL but didn't run the decript after,  would this cause this issue?   The car is store off site so I will drive in the morning and try this.   But what other issues could this be?

0

Signs of a decryption issue (Bypass) on a VW Jetta 2015

I have installed a EVO ALL on a Jetta 2015 TDI (Push Start - Automatic). I have the EVO ALL, THAR-VW1 and TB-VW installed as per instructions (I decided to skip the trunk release wiring as I didn't find the feature useful for me case). The EVO All is programmed with Diesel Option enabled and it went through the Decryptor without any issues. But when I press the 3 lock sequence. It doesn't start or crank. I see the red light turns on, and then the yellow light turn on... and it repeats this procedure twice (as per the options programmed). The dash of the car doesnt come on (as expected) during the sequence. I will check the brake lights when I have time but I was wondering if there is possibly something wrong with the bypass. Thanks

0

Fortin Evo-ALL will not program

2018 VW Tiguan Standard Key, Automatic Trans, no Heated steering wheel I have the THAR-VW6 installed correctly. The EVO-ALL will not program. When trying to program, I hold down the programming button and connect the data link cable, light goes to blue, I release, all 3 light flash. I have an R-link and a Flashlink. I've flashed the EVO-ALL with the correct firmware. Service# 001A07 367521 Please help.

0

EVO ALL Stuck in Yellow and Red Light Flashing

Hello, I am installing this on my 2012 VW Tiguan. I followed the process guide 92511. After decryptor and returning the vehicle, yellow and red LEDs flash, instead of staying on like explained on Step 13. Now it says my unit (SN 001A07 559614) has recheaed its limit and I am really stuck. Can you please assist? Thanks, Andrew

0

EVO All Decryptor count reset request

Hello, Could you please reset the decrepytor on my EVO-ALL SN 001A07 559614. Thanks, Andrew

0

EVO ALL 2020PTS MAN TRANS, NO BRAKE OUTPUT OUT OF EVO ALL

2020 VW JETTA PTS MANUAL TRANS, FORTIN EVO ALL BYPASS DIRECTED 5706V 2-way remote start, Fortin unit is not doing hand brake out put any suggestion where to start