Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2011 Lincoln MKT key bypass programming will not show red led when pressing brake pedal.

I am trying to do the key bypass steps as described in the stand alone Evo All Lincoln MKT 2010-2014 installation instructions, but getting stuck after being told to insert the oem remote (without battery) into the keyport and press and release the brake pedal to get the unit to display the red LED. The unit only continues to disply the yellow LED despite me pressing and releasing the brake pedal (waiting 5 seconds between each push) up to 50 times. I am using firmware .57, as instructed in the instructions, and have flashed the unit mutiple times. I have also reset the unit and reflashed all to no avail.

08/01/2024

Lincoln TK81 (130Pts.)

0

2007-2010 Lincoln MKX EVO-ALL FORT4/FOR4 No Start

I'm encountering a no start condition with EVO-ALL (SN: 001A07511504) and THAR-FOR4 T-Harness in a 2009 Lincoln MKX. It programs correctly (i.e. ending with 10 red flashes then rapid blue flashes). When remote starting it goes through the motions but the engine never cranks. I currently do not have A4 (green wire - unlock) or A5 (white wire - lock) installed from the 20-pin connector as from my understanding it's only required for a RF kit. I will be installing a MyCar module but want to ensure I have the basics working first before connecting the other wires to the BCM. NOTE: The unlock wire color seems to be incorrect for the 3B BCM connector in Guide # 89131 rev 20220805. The manual states Purple/Green but the actual color is Purple/Grey. Wirecolor also lists the unlock wire as Purple/Grey.

0

1998 Lincoln Navigator EVOALL programmed still doesn't bypass

1998 Lincoln Navigator.EVOALL to use as a bypass. Followed the instructions to a tee for muliple hours could not program. Red and orange light stay on constant. When using two different keys we finally got it to blink red rapidly 10 times and lights when off indicating it programmed properly. Upon remote starting we get the theft light and vehicle shuts off. Remote starts perfectly with programmed key in the barrel.

0

Will the compustar RFX-2W901-ss work with evo-all, evo-one

Just wondering if the compustar RFX-2W901-ss will work with fortin evo series.

0

EVO-ALL Turbo Timer? EVO-One Turbo timer?

Considering installation of Evo all standalone remote starter vs Evo One installation in my 2011 lincoln mks Ecoboost. I would like to take advantage of the turbo timer feature. Does the Evo-all have a turbo timer feature? If not, Will the Evo One have this feature? Thank you very much

0

Will OEM remote still function during remote start

Im am doing a remote start on a 2013 Lincoln navigator and plan on doing it one of two ways. I would like to use an evo-all with an RS1-G5 instead of an EVO-ONE because the range of is far greater then that of the OEM remote, but my concern is will the OEM remote still function will it is remote started. And this same question will go along with the installation of an EVO-ONE and using the 3X lock feature. I havent decided which one I will do yet but I wanted to make sure I knew the answer to this question before I chose.

0

EVO ALL in 2010 Lincoln MKX won't program

I reviewed the other post on this exact issue. At first attempt programming (using programming 3--2 keys) the red led flashed and then blue led flashed. The vehicle wouldn't remote start. I attempted a dozen times changing firmware (4.18, 71.39, 71.35, 71.34, 71.11) and programming using the two key method as well as decryptor process and single key. When attempting to program using the two key method, the red led does not flash, nor does the blue led flash. When using decryptor method, after uploading/downloading and updating the module, the vehicle will not remote start, the security light flashes on the dash indicating no valid key. If I hold the key next to the barrel it will remote start. i swapped out the evo-all for another, same result. I swapped out the evo-all for an evo-ride, the red led does not flash when I press the program buttton. RX (lt blue/blk) is connected to the yellow/org pin 4 of transponder TX (lt blue) is connected to purple/grey pin 3 of transponder connector. I tried swapping RX and TX, module wouldn't go into correct programming mode. I tried using the guide for Ford Edge, connecting evo-all relay output (Wht/blue, wht/red) to +12v, ign. 5 hours troubleshooting this thing. Normally changing firmware solves these type of issues, but I am at a loss.

0

for lincoln town car

good morning i want system that no need to cut wire i need plug only as i saw in videos in youtube wich system can i choose evo- all or evo-one? I have a town car 2009

0

2010 MKX EVO-ALL PROGRAMING

Programming remote start with evo-all. 2 key system 2010 mkx, does just what it says it will do all the way to the end, then try remote starting and the remote starter just clicks and won't crank the car, if i remote start the car with the key by the ignition cylinder it will start.

1

lincoln Navigator - 2nd Attempt to get support from this website

I follow programming proceedure 2. I install the first key for 3 seconds and the yellow light comes on. I remove it and install the 2nd key and then the red light flashes once.  Then I remove it and press the program button and the red light flashes once quickly/weakly.   I use the remote start which powers the accessory wire but never get the red light 10 flashing times. The red light just stays on.  Can you tell me why the programming is no working?

 

0

Programming Evo all for Lincoln navigator with 2 keys

I follow programming proceedure 2. I install the first key for 3 seconds and the yellow light comes on. I remove it and install the 2nd key and then the red light flashes once. Then I remove it and press the program button and the red light flashes once quickly/weakly. I use the remote start which powers the accessory wire but never get the red light 10 flashing times. The red light just stays on. Can you tell me why the programming is no working?

0

2012 Navigator Encrypter issues

using the encryption method with EVO-ALL, everything goes as described. Navigator started two times just fine. closed the door and armed the alarm, now it sets the alarm off when I request start ???

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer