Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2015 Corolla, flashes 4 red flashes & 3 red flashes

I have a 2015 Corolla with an automatic transmission start button. 

Installed with THAR-TOY6 T-Harness & EVO ALL

The device flashes blue when opening or closing the doors, but when trying to operate it with the remote, it flashes 4 red, I keep trying to program it and it gives me 3 red flashes.

SN:001A07261560

Flash blue once before red flashes

Please see the attached video.

https://photos.app.goo.gl/6rfod5uAwRBQ7MgUA

0

INT-SL+ not programming on 05 sequoia.

Int-sl+ not responding when hit the lock button. Red light just stays on.. no flashing, no nothing. Any idea? It's flashed to firmware 0.17

0

EVO All works a few times then won't start and red led flashes 5 times

2009 Toyota Venza Push-to-start. Installed EVO All and worked gopod for a couple days and then when customer tried to used the remote start, the parking lights blinked and the red led flashed 5 times but car did not start. SKU #: B-3475-455

0

Flashing red near programming button and module not responding to remote

Remote doesnt work after change car battery. Tried reprograming but not helping. Noticed red light blinking near programming button not the red with the other yellow and blue led. What could be wrong?

0

Solid red light after downgrading firmware.

0

Cranked but doesn't start; solid red & yellow light (after it cranked)

Hello, I've installed Evo-One on Toyota Camry 2014 G Key. After successful programming (installation), when I use OEM 3x lock to start the car, it cranked but failed to star; the unit shows solid RED and Yello clor. Any hi9nt pleasee? Thanks, Qamar

0

Solid red LED on EVO ALL 2011 Toyota 4runner

I had the remote start working before putting the vehicle back together. Put it back together and it stopped working. Re programmed the tach data. It worked. Put the vehicle back together again. Another failure. I took everything back apart. Checked all my wiring again. Nothing grounded out. Try to restart with the EVO all and while holding the program button and plugging in the black four pin connector in, the red led stays solid. I can hit the red program button and it allows me to start reprogramming the options but it doesn’t sense the brake pedal eitherbcor me to confirm the options.

0

Evo-All and Viper remote start Not working -2016 Toyota Rav4 - Evo-All Solid Red light

I finally had time this evening to install the remote starter but i believe the bypass is faulty.  I used the instruction provided in fortin website using the code(as usual).  I connected as is exactly as in the diagram..

- Hardwired wires from evo-all to Viper 5305 module as per dotted lines in the diagram....no more, no less.  

- Cut red and black wire of Datalink cable,  then connected Red to 12v and black to ground.  

- From Evo-all Connected Yellow(Ignition), Lt Blue/black(IMMO Data, Green/red(driver hoodpin and Lt Blue(Door lock data) as per diagram.

- Programmed the Evo-all as per instruction(it seems it worked according to Flash pattern in the diagram instruction.

-  I pressed lock/arm in Viper remote,  transponder and viper module communicates no problem which i can see on the viper's  antenna LED and siren chirps as it should.  even unlock button works as well between transponder and Viper module.

 

 

Now the problem........

- nothing happens to OEM arm/disarm when lock/unlock is pressed on the transponder.

- nothing happens to Door's lock/unlock  when lock/unlock is pressed on the transponder.

- no crank when remote start is pressed.  But transponder shows it did send the signal.

- when Viper is armed,  I can open any of the doors and alarm won't sound nor security system work.

- i know Viper is Working fine because when it's armed and start the engine using Key,  it didn't crank and alarm sounded...loud.

-  also,  no parking lights flashing or turning on.  But if i connect the Parking light from Viper to car instead of through evo-all,  then parking lights works.

 

After couple of hours trying all the tests  I know the module is not sending any info to either Car or Viper module.  I did a little more test by arming OEM security using car's FOB,  armed Viper by pressing lock,  then tried to remote start and voila,  it would crank but won't continue because the evo-all bypass seems not bypassing.  I reset/re-programmed  the module then suddenly all i got is solid Red bottom light.  It stays Red even after unplugging every wires then re-plugging it the datalink by itself.  It won't re-set anymore. 

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer