FORTIN EVO-ONE-912 with no blinking LED after follwing all inestruction igntion on off on 4x brake padel the blue led wont come on or flash.the red led under the loop in the evo one flashes but the ANT900 not responding at all.

- when i plug the wire in the ant 900 led will blink ones and thats it and when i try to update the RFkit by flash link updater it wont dedect it . i am suspecting ANT900 anttina defected.Any help ? thanks

FORTIN EVO-ONE-912 with no blinking LED after follwing all inestruction igntion on off on 4x brake padel the blue led wont come on or flash.the red led under the loop in the evo one flashes but the ANT900 not responding at all.

- when i plug the wire in the ant 900 led will blink ones and thats it and when i try to update the RFkit by flash link updater it wont dedect it . i am suspecting ANT900 anttina defected.Any help ? thanks

I undertand that if I wanted to use the Directed 7756V remote I will need to add the XL XL202 RF to Data converter to my EVO ALL.  My question is which antenna will I need to purchase in order for the 7756V remote to work.

2015 infiniti Q40 evo-all remote-start rf-kit push-to-start 

I have a 2018 Toyota RAV4 Hybrid and I've successfully installed the EVO-ONE and it works perfect.  I'm now adding an RFK912 RF kit.

Where is the best place to install the antenna?

Usually it's placed at the center of the windshield behind the rear view mirror, but the RAV4 has a camera/radar box there.  Can I safely remove the box and install the antenna inside it?  Should I place the antenna outside (and next to) the box?

Also, is it easy to remove the rubber around the door frame to route the antenna wire from the main ECU area (where the remote starter is) up to the rear view mirror area?

Thanks for any help!

Hello,

I have the Evo-All installed in my 2011 Ford Fusion, an installation that has been in place since January of 2014.  I recently attempted to add the CRIMESTOPPER RFALL641W FM RF Add-on Kit and the Crimestopper Tele-connect smartphonne control.  I am able to program the Evo-All to "see" the RF kit (if the Tele-connect is disconnected), and I am able to program the Evo-All to "see" the Tele-connect as long as the RF antenna is disconnected.  But I am not able to get the unit to see both add-on devices at the same time.  I have flashed the unit as instructed.  If I have both connected at the same time, the RF kit works, but the Tele-connect does not.

Any ideas?  Your assistance is appreciated.   

I just installed the EVO-NIST1 standalone with the Fortin RF642W RF Kit on a 2008 Infiniti G35x according to Guide 24031 and have a couple comments & questions after playing around with it:

1) LOCK x3 works with the OEM fob, however it cannot remote stop the car with LOCK x3 again. This is known, so it is not a problem.

2) After remote starting the car and unlocking it (either with door button or with either of the fobs), I can open the door, step on the brake, and I am able drive away. That works as intended, but the problem is I can drive away without having the OEM key fob around. The instrument cluster screen does not say NO KEY like it normally would if the key has left the car. In other words, one would be able to drive off without having any remote on them as long as the car gets remote started followed by an UNLOCK signal. Are remote starts intended to bypass the need to have the OEM Intelligent keyfob for the take-over?

3) While the engine is off, the LOCK signal from either the RF fob or OEM fob will lock the doors and prompt the RF antenna's LED to start flashing (blue) and will not stop unless I press the UNLOCK botton on either remote. What is this flashing for? Can this be disabled? I do not need or want any alarms or extra security features. I am more concerned about it draining the car battery. Please advise.

4) After remote starting, the first press of UNLOCK with the RF fob ONLY turns off the Antenna's flashing. I have to press unlock a second time to unlock the car, however it would unlock all four doors at once. I had configured it through Flash Link (B1 on) to unlock driver door on first press, and lock all on second press but that isn't the case. What exactly happens on the first UNLOCK that stops the antenna's LED flashes? Can I get the unlock button to unlock the doors on first press?

5) How does IDLE mode pertain to push-to-starts where the key does not need to be in the ignition? I'm guessing it is not needed but just want to be sure.

6) I had to use the RL2 connector to get remote starter to work, although the guide says RL1 for G35. This might be the issue with folks who cannot get their '07 - '08's  to remote start.