English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

09/12/2024

 Chevrolet Jeff Cates (320Pts.)

0

Dead unit or gremlins?

2004 Suburban LT Evo-One with Fortin 4 button 1 way remotes. Reset the unit several times. Here's some more interesting info...the valet button doesn't do anything. I've replaced the valet button as well as just touched the wires together and still nothing. So doing a complete 23 reset is not possible. Today I figured I would rewire the 6 pin harness, to eliminate the t connectors. No change. It goes thru the start sequence, clicks once and then just like the key was turned off. It will act like it does a remote take over as well. When running, if I press to "leave" the vehicle but have it stay running, it clicks like it's ready. As soon as I turn the key it shuts down. It's getting cold and dark and I have maybe a few hours on weekends to try to figure this all out. I have uploaded a video on YouTube. https://youtube.com/shorts/85TdkOkl8Y4?si=04Yf5ICgBzh9n734
Connectez-vous pour répondre Voir 1 réponse(s)

31/10/2024

 Chevrolet Jeff Cates (320Pts.)

0

Where to start?

Ok, fighting this thing for months. I bought a new module, programmed it, installed it, get the same no start as I did with old unit. I took the new one and reset. Reprogram and tried again and still nothing. I can't even get it to allow me to program the remotes to test the start function. So pulled it out, put the old one in and it tried to start after I pulled the OBD wire. Plugged it in and it started and ran for a few minutes and I tested everything. Great it works again...next morning, doesn't work. Single light flash and nothing. I started it with the key, did a remote start transfer and it took over. I pulled the key out and it stayed running for about a minute, then stopped. I tried again, nothing. So after 8 hours, I tried to remote start and it did, ran for about 10 seconds and shutdown. What's going on? Do I have a wire gremlin on the vehicle side? I disconnected all the harnesses wires, plugged them all back in and still nothing. Is there an alternative wiring?
Connectez-vous pour répondre Voir 1 réponse(s)

10/08/2024

 Chevrolet Hassan Shabib (160Pts.)

0

Chevrolet spark 2020 push to start remote not responding to remote start

The Evo all-GM6 device was installed and programmed, but the remote that was programmed in the steps does not start the car with remote start, and the remote start only works with the other remote
Connectez-vous pour répondre Voir 1 réponse(s)

27/01/2024

 FAQ Ark :D (130Pts.)

0

Possible to install an EVO-ALL module for transponder bypass, with no remote start unit?

Hello, A more complete version of my question is; I am looking to purchase a Fortin EVO-ALL unit to install in my car and I have no need or want for remote starting functionality; I ONLY need the key transponder bypass functionality. Is it possible to install the Fortin EVO-ALL unit alone, with no remote starter unit connected, to simply store and emulate the transponder key? Background: a couple years ago, I built a tube-frame kit car using a Chevy with PK3+ donor car, and I would like to add a push-button starter to the car now. One of my requirements for this project is that the factory ignition switch is to be removed. I have a custom PCB in my possession that handles the ignition switch side, but now I need to handle emulation of the key transponder/immobilizer bypass side. I understand that there's plenty of other products available to do this, but I need one that will not rely on a resistance loop around the transponder ring, since the factory ignition will be removed. Thanks in advance!
Connectez-vous pour répondre Voir 1 réponse(s)

08/12/2023

 Chevrolet Antonio Canady Sr. (130Pts.)

0

Do you make a remote start kit for 1993 Chevy s10 blazer

I bought the Bluetooth Flash . I want to do installs . Id like to start with my own . It’s a 1993 chevy s10 blazer non power interior. What products do I need for installation
Connectez-vous pour répondre Voir 1 réponse(s)

03/10/2023

 Chevrolet Emt medical (130Pts.)

0

2023 Chevy Blazer

Do you have any solutions available for the 2023 Chevy Blazer? Was there a change in can data from the 2022 model?
Connectez-vous pour répondre Voir 1 réponse(s)

31/01/2023

 Chevrolet Nodier Vallejo (1030Pts.)

0

chevy colorado 2006 doesnt start

I have programed a evo all )1a07248861) for colorado 2006 standard key, using it with a remote start crimestopper rsg4, everithing is fine with de programation, the door  lock and unlock is working fine.   but the problem is when i want to start it, the lighs turn on , the inition , accesory, etc. but the car never run with de starter and it doesnt starte,  the evo all stay whith de lihgs yellow and red solid and the lights never turn off.   i tried programing diferents evo all and the same thing happened with them.  
Connectez-vous pour répondre Voir 0 réponse(s)

13/01/2023

 Chevrolet Trey Heier (130Pts.)

0

'18 Malibu Flashing Headlights & DRLs

Hello, I have an '18 Malibu smart key and I have installed the EVO-ALL module and programmed. While the car is starting via the module, it seems it is glitchy. The dash turns on and off, displaying different messages, and the headlights and daytime running lights will turn on and off as well. This ends with the headlights off, DRLs on, and brake lights on. My question is if this is normal? And if so, I would suggest an update to the module. One time I remote started the car and after a second, the dash displayed No Remote Detected, then everything turned off and then the car started after a few more seconds. I noticed the harness has a couple loose wires and a couple other connectors attached. Do these need to be connected to anything?
Connectez-vous pour répondre Voir 0 réponse(s)

09/01/2023

 Chevrolet Eddy Weakley (190Pts.)

0

2006 Trailblazer will start once and won't start again.

2006 Chevy Trailblazer with an Evo-All and an rs4-g5. The locks work and it will remote start one time. When trying to remote start a second time, it will crank and fire, but not start. When this happens, the Evo-All has the red and yellow lights on solid and the blue light flashing. If I remove the 4 pin data wire from the Evo-All and reconnect it, the lights go out and it will remote start again. Then the problem starts all over.
Connectez-vous pour répondre Voir 1 réponse(s)

06/12/2022

 Chevrolet JEREMY WHEELER2 (160Pts.)

0

Can I use a RF kit connected to my evo all to control my crimestopper remote start?

I have the remote start working but my wife washed the 2 way remote. A new one is more expensive than an upgraded RF kit. Can I plug the rf kit into the evo all to control the start and door lock functions of the Crimestopper or plug the rf kit directly into the crimestopper?
Connectez-vous pour répondre Voir 1 réponse(s)

27/03/2022

 Chevrolet Mike Herriman (260Pts.)

0

2008 Equinox runs for 45 seconds then shuts down

I just installed a Viper 4305 remote starter with EVO-ALL in 08 Equinox. I followed the installation instructions, got the EVO-ALL programmed and Decryptor completed. The remote starter seems to function as expected: Door Lock Door Unlock Remote Start Remote Stop Brake stop Hood stop. Although, when remote started, the vehicle only runs for 45 seconds then shuts down. I was not able to see any diagnostic light flashes. One thing to note is the vehicle does have factory remote start enabled...I would not think that's the issue though. Any suggestions? Thanks
Connectez-vous pour répondre Voir 2 réponse(s)

27/03/2022

 Chevrolet Mike Herriman (260Pts.)

0

2008 Equinox runs for 45 seconds then shuts down

I just installed a Viper 4305 remote starter with EVO-ALL in 08 Equinox. I followed the installation instructions, got the EVO-ALL programmed and Decryptor completed. The remote starter seems to function as expected: Door Lock Door Unlock Remote Start Remote Stop Brake stop Hood stop. Although, when remote started, the vehicle only runs for 45 seconds then shuts down. I was not able to see any diagnostic light flashes. One thing to note is the vehicle does have factory remote start enabled...I would not think that's the issue though. Any suggestions? Thanks
Connectez-vous pour répondre Voir 2 réponse(s)

18/02/2021

 Chevrolet john brooks2 (130Pts.)

0

do you need a RFA2A for RFK411 button remote with an EVO all GM1 t-harness?

2012 cruze standard flip key oem,
Connectez-vous pour répondre Voir 1 réponse(s)

18/01/2021