Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

25/01/2022

 Jeep PEDRO CASTILLO (150Pts.)

0

Connecting ACC from Alarm to EvoAll-TharCHR5 Wrangler

I have installed on my Wrangler 07 a PKE EasyGuard EC002 with a Push button Start and Hard Wired to EvoAll-TharCHRT5, I got everything work but ACC mode. I didnt know where to connect my ACCesory + Output from my Alarm to EvoAll and chose wire to Lose Yellow wire on Thar-CHR5 harness. But when I select ACCesory mode on push start button (1 click no foot on brake) the car goes directly on RUN mode, which I guess is because I wired to the Yellow Wire which is RUN mode and not ACC. In wiring information of Wrangler 07, it use a single MUX cable to send the signal of ACC and START, according with that, to get ACC Mode it has to Ground wire throught a 560 resistor and a 150 ohms resistor to START So I guess I have to use a relay to convert the ACC + mode to ground plus the 560 resistor and maybe the MUX Green/Red Cable (A18)? How can wire my ACC output from Alarm to EVO to set the ACC Mode the right way? TIA
Login to reply View 1 answer(s)

26/02/2020

 Jeep Natalie Maldonado (880Pts.)

0

P0830 code came up after weeks of nstallation (EVO ONE with manual transmission bypass 2017 Wrangler)

After installation of 5 pin relay and successful remote start, the check engine light came up randomly....so far two times. What can be wrong?
Login to reply View 1 answer(s)

04/02/2020

 Jeep timothy williams (190Pts.)

0

evo all with rfk411 starts 2014 wrangler but immediately shuts off

i have the evo all, updated firmware, corrected the setytings in the flashlink to use H2 for the rfk411,what els eshould be enabled? the jeep starts, runs for 2 seconds and then iss witched off again by the evo all. then the evo has the red and orange light solid.
Login to reply View 0 answer(s)

04/10/2019

 Jeep Mike Siciliano (130Pts.)

0

‘18 Wrangler - Remote start shuts engine off when doors are off

I have a 2018 Jeep Wrangler. I installed the EVO-CHRT6 Stand Alone, vehicle remote starts and everything works fine with the doors on. Remote start the vehicle, unlock vehicle, open door, get in, close door, hit brake, lights blink twice, vehicle is not using Fortin anymore. As a wrangler owner, we take the doors off. When I remote start the vehicle with doors off I follow a similar process. Remote start vehicle, unlock vehicle, get in, hit brake, vehicle shuts off and lights blink twice, which then I'll have to use the push button to start vehicle back up. How can I fix this? The remote start needs to recognize the doors opening and closing rather than just the unlock being pressed.
Login to reply View 1 answer(s)

04/10/2018

 Jeep Steven Turvey (130Pts.)

0

tach output appears to not function

I have a 2018 Wrangler JK, everything appears to be functioning correctly with the exception of the tach output. Am using the evo with the advanced keys push to start system. I was not able to locate a setting in the flash updater for turning the tach output on or off.
Login to reply View 1 answer(s)

25/09/2018

 Jeep David Cunningham (320Pts.)

0

Where is the Tach wire on the EVO-ONE

2014 Wrangler manual transmission I have no remotes for this unit and plan on using the OEM remote. The unit will not remote start. The flash tool says that the tach wire needs to be hooked up, not to use the tachless mode. So, Which wire is it? I will need the PIN number too since the extra wires have been removed to reduce the wires in the install.
Login to reply View 1 answer(s)

31/01/2018

 Jeep DAVID WALTERS2 (230Pts.)

0

Stand alone remote start function not working 2015 Jeep Wrangler

EVO CHRT5. connected yellow wires. Did not connect purple wire. Flashed module to recommended firmware 74-32. followed instructions, Moduled flashed blue, flashed rapidly etc. Blue light turned off when hit factory remote lock button. But car will not start when pressing lock three times. Nothing lights up on the dash. I notice the factory red LED is flashing on the dash for the factory alarm the entire time but not sure that means anything. The Options selected are all A1 to A11 ON, C1, D1, D1.1, D1.2, D1.6, D2 all ON. Everything else is set to OFF. I have reset the module, flashed it again, confirmed options, etc several times. No luck. Any idea what is wrong?
Login to reply View 1 answer(s)

10/01/2018

 Jeep J C (160Pts.)

0

While vehicle is already running can the Fortin remote start be used to keep it running after the key is removed?

While vehicle is already running can the Fortin remote start be used to keep it running after the key is removed? If so how can this be done?
Login to reply View 1 answer(s)

05/01/2018

 Jeep timothy williams (190Pts.)

0

fortin evo chrt5 can i use aftermarket key fob

can i use an aftermarket key fob for the fortin evo chrt5-- my oem key is NOT a keyless entry, my jeep has an after,market kit
Login to reply View 0 answer(s)

04/01/2018

 Jeep timothy williams (190Pts.)

0

2014 wrangler with aftermarket keyless entry- use those remotes?

I have the electric life 95338 (https://www.electric-life.com/product/95338-4-door-power-door-lock-kit-w-keyless-entry ) since my jeep came with manual locks.. will the Fortin Evo chrt5 work with those remotes? I do not have a factory keyfob
Login to reply View 0 answer(s)

02/01/2018

 Jeep ANTHONY MCMAHON (150Pts.)

0

2014 Wrangler Does Everything But Start

I believe I have done everything correct but when I try to start the blue light flashes each of the 3 times I hit the lock button but the jeep doesn't start . What am I missing ?
Login to reply View 1 answer(s)

05/09/2017

 Jeep Lucas Canales (130Pts.)

0

EVO CHRT5 compatible with 2016 Jeep Wrangler CRD?

Will EVO CHRT5 work with 2016 Jeep Wrangler Sahara CRD (2.8 diesel automatic)? Also - will they work with the jeep keyless 4 button as well?
Login to reply View 1 answer(s)

26/01/2017

 Jeep Kyle Gray (130Pts.)

0

2014 Jeep Wrangler, Evo Chrt5 with T-Harness will not remote start, all light blinking

I recently installed an Evo CHRT5 with T-Harness into my 2014 Jeep Wrangler (2dr), the remote start functioned properly the first couple times I tried it. Now it will not remote start, when I looked at the unit all three lights were blinking one at a time. I've unhooked everything and went through the reinstall process multiple times but every time I do this it will only function for a few days/remote starts. Then it goes back to cycling through the lights and not remote starting.
Login to reply View 1 answer(s)

24/12/2016

 Jeep stephen bogle (160Pts.)

0

2016 jeep wrangler y harness & T harness connections

is the only wire i have to connect to the y harness and T harness the sold yellow? I see in some installs it looks like the sold green is used as well. Thank you.
Login to reply View 1 answer(s)

01/12/2016

 Jeep yannick polasek2 (1950Pts.)

0

jeep wrangler 2017

Hello wondering if evo-all/ evo-one compatible with a 2017 wrangler ? if not when should i be able to do them ? thanks
Login to reply View 1 answer(s)

27/01/2016

 Jeep Sean Grzech (230Pts.)

2

Does the EVO-CHRT5 work with the Drone DR3400?

I have the EVO-CHRT5 remote starter installed on my 2015 Jeep Wrangler Unlimited. I want to add the Drone DR3400 to it so I can start the car from anywhere and keep an eye on the door locks and such when I have the top off. Is this compatable?
Login to reply View 1 answer(s)

15/12/2015

 Jeep Scott Dudenbostel (140Pts.)

1

Engine won't shut down, now red/blue flash at last step

CHRT-5 with T harness installed in 2012 Jeep Wrangler auto as stand alone. After 2 days, engine would not shut down when key removed or 3 push on remote. Reset, flashed and reinstalled, when I get to last step, blue and red led alternate and engine will not shut off with key removed. Can only stop engine if unplug evo. I tried Master reset, I have flash link , updated and flash options again. What do I do next?
Login to reply View 1 answer(s)

21/05/2015

 Jeep alex pal (130Pts.)

0

JK CRD ne demarre pas

Bonjour connect
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue