Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2006 chevrolet impala using evo-all stand alone install - no lock/unlock and accessory connection

Hello all, good day. Just wanna ask if i do the evo-all stand alone install with rf642 on this 2006 chevy impala, will the lock and unlock and accessory work through the vdata cable? Without physical connection? i experienced this with a 2007 nissan xtrail, it has a data connection but lock/unlock doesnt work. I had to physically find and connect them. (Using. Evo-one) thanks in advance.

1

RF642W - Two way communication not working

In order to have a remote with each physical key, I purchased a 2nd RF642W kit. After pairing the remotes from the 2nd kit to the vehicle the remotes work in that they are able to preform all the functions. However, they don't appear to recieve 2 way confirmation. The most annoying part of this is when I press lock/unlock on one of the 2nd kit's remotes the vehicle locks/unlocks 3x before the remote says it did not work (even though it did). Is there a way to get the remotes from the 2nd kit to recieve the 2 way confirmations?

0

RF642W remote batteries dead within a week

I am having an issue with my RF642W remote. The batteries in the remote are dying within a week of being installed, even though I have tried using new batteries and changing them multiple times. The remote functions normally when the batteries have a charge, all buttons work and nothing is stuck down. The LED and chime on the remote also operate normally. Can anyone suggest any further steps I can take to investigate this issue or is this a symptom of failing hardware?

0

RFK942 Remote LED

When I start my G37S which uses the RF642W remote, the RF642W remote's green LED flashes once every six seconds when the car has been started remotely. On my Q50, which has the RFK942, when the car has been started remotely the LED of the RFK942 remote flashes once every 10 seconds. My question is, is there is a way to change how often the LED on the RFK942 remote flashes? This trivial and certainly no "deal breaker" since I do preferrer the RFK942. I was just wondering.

0

RFK942 not working after disconnecting and reconnecting the car battery

After getting the RFK942 working I did some maintenance on the car. I disconnected the battery to perform the maintenance required and after reconnecting the battery I attempted to lock the doors with the RFK942 remote. The remote sent the signal but doors did not lock (LED turned red). I thought that perhaps the antenna needed to be reprogrammed so I attempted to perform the programming procedure again. The antenna would not program (no blue LED) so I connected it to the Flashlink Manager to see if something had been turned off. The Flashlink Manager did not recognized that the antenna was connected. From this I am gathering that the antenna was damaged when I reconnected the car battery. Is this possible? If so, what can I do to prevent this from happening again? Would a different RF kit work better (for example the RF642W)?

1

Can the remote start from OEM keyfob be disabled when I install an RF-Kit to my EVO remote starter?

Can the remote start from OEM keyfob be disabled when I install an RF-Kit to my EVO remote starter? I'll be installing an RF-All 642W with my existing EVO-CHRT5 (that currently starts with the OEM 3x Lock button). Can the OEM 3x Lock be disabled so only the remote from the RF Kit will start the car? the 3x Lock hasn't worked great for me because my wife has a bad habit of hitting the OEM lock more than one to "make sure" the car is locked. If not, what mode would you recommend I use to minimize accidental remote starts? I think I saw Lock-Unlock-Lock, but hoping it can just be disabled.

1

Can the remote start from OEM keyfob be disabled when I install an RF-Kit to my EVO remote starter?

Can the remote start from OEM keyfob be disabled when I install an RF-Kit to my EVO remote starter? I'll be installing an RF-All 642W with my existing EVO-CHRT5 (that currently starts with the OEM 3x Lock button). Can the OEM 3x Lock be disabled so only the remote from the RF Kit will start the car? the 3x Lock hasn't worked great for me because my wife has a bad habit of hitting the OEM lock more than one to "make sure" the car is locked. If not, what mode would you recommend I use to minimize accidental remote starts? I think I saw Lock-Unlock-Lock, but hoping it can just be disabled.

0

Key fob cover

This is just a general (and perhaps silly) question concerning the RFK942 and RF642W key fobs. I am looking for a means to protect my key fobs. I have my vehicle key fobs protected with silicone covers. Is there something available for the RFK942 and/or the RF642W?

0

how do I program RF642W fobs to work on Evo-one?

i have installed an Evo-one on my 2019 mazda cx5 and the OEM key fob 3x lock start is working fine. I have also included the RF642W when i programmed / flashed the module. I am not sure what to do next to make the rf kit functioning. i am a bit confused with the quick guide. I dont get the same response from the system (as stated on the guide) when trying to do the steps on programming the fobs. not sure what I am missing.

0

how do I program RF642W fobs to work on Evo-one?

i have installed an Evo-one on my 2019 mazda cx5 and the OEM key fob 3x lock start is working fine. I have also included the RF642W when i programmed / flashed the module. I am not sure what to do next to make the rf kit functioning. i am a bit confused with the quick guide. I dont get the same response from the system (as stated on the guide) when trying to do the steps on programming the fobs. not sure what I am missing.

0

Should I connect the lt. blue wire

I’m putting an evo-all in my 2016 Cruze limited with an rf kit. The instructions say units from 2017 to December 2018 need to have the lt. blue wire connected. My unit was manufactured January of 2019. I wasn’t sure if the guide had been updated and therefore didn’t know if I should follow page 6 or page 7 of the guide.

0

Can the audible beeps from the FTX64-2W remotes be disabled?

Evo-all installed on a 2015 Ford F150 using the ForT3 harness and RFK642 2 way RF Kit using the RFALL. Absolutely works perfectly and has exceeded my expectations! Is there any way to disable the audible tones that play on the remote to let you know the vehicle has received the signal? I would much rather just watch the lights and not hear the remote. If not will the Fortin RM942 Or 442 kit do this? I would love to be able to shut off the remote beeps. I've searched everywhere for the answer for about a day before asking. I do like being able to see the green light confirmation that my vehicle has received the signal and the subsequent green LED that flashes every ten seconds so I don't want to go to a 1 way kit. Thanks.

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.

0

08 Nissan Pathfinder - RF642W Lock Button Locks, Unlock Button Locks, Programming Settings or Wrong Wire?

2008 Nissan Pathfinder S - Standard Key - OEM Alarm Fortin EVO-ONE With NIS2 Harness Guide Followed: 75611 Unit was flashed to recommended/newest firmware prior to install. Service No: 002B07 200206 Everything is installed and working (As far as the Remote Starter Goes). When using the OEM Remotes the vehicle will lock and unlock as it always has. However, when using the RF642W remotes, The remote start works flawlessly (Push button, parking lights on, start/Crank, Run) The lock button locks the doors, but the unlock button also locks them (and does not unlock). The OEM Remote will unlock the door as normal with the remote starter running, but I would really like to not have to carry two remotes with me. Vehicle Running Oem Remote: Only Solid Yellow is on, No Blue Flashes RF642W: Lock - Solid Yellow, Blue Flash - Locks Doors RF642W: Unlock - Solid Yellow, Blue Flash - Locks Doors Did I miss a step? Enable/disable a wrong option? Any help is greatly appreciated. Thank You in advance.

0

Antenna light blinks constantly

I installed a 642w long range 2 way kit on my Silverado today and just noticed that the blue led on the antenna is constantly blinking. Is it supposed to blink 24/7 if the truck isn't running?

0

No foot brake confirmation from EVO ONE or RF antenna when programming RF642W step 4

No foot brake confirmation from EVO ONE or RF antenna when performing step 4 programming RF642W on Hyundai Elantra 2009. Tested foot brake output at 0.02 volts and tapped in to positive foot brake per instructions. Im thinking voltage from car is too low and EVO won't register activated foot brake and this is preventing me from completing programming step 4.

0

No foot brake confirmation from EVO ONE or RF antenna when programming RF642W step 4

No foot brake confirmation from EVO ONE or RF antenna when performing step 4 programming RF642W on Hyundai Elantra 2009. Tested foot brake output at 0.02 volts and tapped in to positive foot brake per instructions. Im thinking voltage from car is too low and EVO won't register activated foot brake and this is preventing me from completing programming step 4.

0

Evo one 2 way paging

Hi, just installed evo one with rf-642w to operate as alarm and remote starter Everything seems to be working fine other then alarm event paging confirmation Is there anyway to have this feature activated or is not part of this system Thanks

0

Evo-one and rf642w not working

Have a 16 Mazda CX-5 running fine with lock-unlock-lock as well a dei smartstart system on a evo-one. Customer now want a to add on a rf642w kit.. I have added these on evo-all in the past without issue by activating in the software and programming the fob’s but this evo-one is having an issue. When I plug in the antenna the blue light turns on and off. I go through the programming on the evo-one using the valet switch, turn ign on hold valet until lights/horn, press and release valet 5x and the. Press the brake... this is where all goes wrong, no led flash, buttons don’t program... what am I missing? No longer find remote control options in the flash link manager for the evo-one.

0

Evo CHRT4 and RF642W

I have installed Evo CHRT4 in my Grand Caravan 2018 with OEM key and it's working great. The CHRT4 was flashed for RF. I am now trying to install RF642W using RFA2A following steps on installation guide. As per the last step on installation guide, I did press & release (-) AND press & release (lock) on RF642w fob, but on CHRT4 it did NOT blink RED and BLUE LED, instead the RED, BLUE, YELLOW LEDs stayed solid on. The fob would sound and show green light [after I press & release (-) and press & release (lock)]. The antenna LED fast blinks (BLUE). I checked wires and everything was good. Can someone help me resolve this? Thank you in advance.

28/05/2019

Dodge 2 (130Pts.)

0

Evo CHRT4 and RF642W 2-Way LED

Hi, I just bought Evo CHRT4 and now I am looking to install RF642W 2-Way LED. I wanted to make sure that RF642W 2-Way LED is compatible with EVO CHRT$. Could you please confirm? Thank you. Bhavik

0

RF642W will not start 2010 Tahoe

I have a really odd problem, I installed an EVO-ALL with GMT4 T-harness in a 2010 Tahoe and added a RF642W remote kit. I can start the vehicle with 3X Lock, but not with the RF642W. I have the RF kit option H2 selected, I got the visual on the EVO-ALL and the blue blinking light on the RF antenna that my remotes got paired with the EVO-ALL, but they still do not work. just for the heck of it I changed it to option H1 and was able to start the vehicle with the lock button on the RF642W, but was unable to shut the vehicle back off. I am not sure why I can not get any reaction from the my RF642W remote with the option H2 selected. Also, this vehicle also had a factory remote start installed, I douibt that has anything to do with it but just thought I would let you know. Any ideas?

0

Replacement antenna cables

Where can I find replacement antenna cables for RF642w add on RF remotes? My last vehicle was totaled and I was not able to remove it.

0

AUX 2 on 2007 Toyota 4runner

I see the Trunk Release/AUX (yellow/black wire) but where is the AUX2 wire? Can the GWR/Programmable wire be used for AUX2? i've seen replies that state that Aux2 is run from the CANBUS, what options are available on an 07 4runner for that? The RF642 remote has an AUX2 function, curious how it works.

0

RF642W No LED

I just installed an EVO-ONE in my 2016 VW Golf GTI Push-to-Start manual transmission using the T-Harness (THAR-VW1).  It was tedious, but it went well.  The EVO-ONE can remote start the vehicle using the OEM remote (3x lock).

Then, I added the RF642W kit.  Just plugged the black harness from the RF642W into the "data link antenna" port on the EVO-ONE.  I can't get the 642 to do anything.  I tried to program the remote transmitters but I cannot get the LED to come on.  I don't have a valet switch installed, so I'm using the ignition on/off method.  On-Off-On does not set the LED.  I've just setting the ignition "on" off 3 times and starting/stopping the vehicle 3 times (the instructions assume you have a key, not push-to-start).  Nothing.

What should I do?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer