Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

28/10/2021

 Chevrolet Carlos Paige (750Pts.)

0

Evo One not recognizing brake signal or key take over

I have an Evo One starts and stop from FTX64- 2W, tried it in two different vehicles same result. It's not recognizing key take over or 12v to black wire in 20pin connector to shut down. I read in a post, Derek mentioned wiring in a relay from the brakes that would send ground signal to the hood pin wire. Sounds like it will work. Will it have any adverse effect while driving, sending ground signal to the hood pin while driving if the key is not being recognized as being switched on?
Login to reply View 1 answer(s)

01/01/2020

 Subaru brian furr (170Pts.)

0

car starts then shuts down

I am installing an Evo one in a 2013 Subaru Outback with automatic transmission. The module was flashed with the correct software and programmed correctly and when I remote start it, it starts then shuts down. It tries a second time and then park lights flash 4 times The SN of my module is 002B04 051414
Login to reply View 0 answer(s)

07/05/2019

 Toyota RYAN TURNER (130Pts.)

0

2016 Toyota Highlander Window up/down feature

Is it possible to connect the window up/down feature on my highlander?
Login to reply View 1 answer(s)

03/03/2019

 Infiniti Josh Ley (500Pts.)

0

2009 Infiniti FX35 starts, shuts off after a minute or less

Crimestopper RS7-G4 with evo-all, firmware 72.37. has worked fine for several years. Had an issue several months ago that was resolved by updating firmware to 72.36 and reprogramming tach (would start and stall) Now, it’ll start, stay running, and shut down after a minute. Attempt to restart, run for a shorter amount of time, and same on third attempt. I changed firmware to 72.33, 72.34, 72.35, 72.36, 72.37 all with similar results. 72.32 (as recommended in guide 34361) Is this a faulty module? Or is there another possible solution
Login to reply View 1 answer(s)

20/12/2018

 Ram fred Mailhot (130Pts.)

0

Window won't roll down

Hi, I own a ram 1500 2018 and the roll down or up windows mode is not working when using the app on the phone?
Login to reply View 1 answer(s)

01/12/2018

 Toyota HAI TRAN (210Pts.)

0

Toyota Rav4 2018 Push To start won't shut down when door is open.

I bought the Evo All with the Fortin T6 harness for my Toyota Rav4 2018 Push To start.

I updated the Evo with the newest firmware.  I turned on the  option "Engine Shut down when door is open".  The problem is the engine DOES NOT shut down when I open the door.  I step on the brake and move the out of park, the engine shut down and then automatically starts up the engine again. 

 

Problem solved.

I stood too close to my car when I remotely started it.  My car did not start so I turned off some of the options.  I reloaded  the suggested options.  My car starts up and shuts down when I open the door.

 

Thank you !!...............

 

 

Login to reply View 1 answer(s)

28/02/2016

 Nissan Jared Pearson2 (220Pts.)

0

EVO-NIST1 - Shuts down if you don't open the door

Hello, I recently install an EVO-NIST1 on a 2010 Maxima with a Fortin 2-way RF kit. I noticed when testing sitting inside the car, if I remote start the vehicle and press the brake the car will shut off. Pressing the unlock button on the RF remote doesn't seem to help. If I open and close the door the handoff seems to function as intended. Is it necessary for the EVO to see the door pin signal before it will allow the handoff to the vehicle? Is there a setting I can change? Thanks!
Login to reply View 2 answer(s)

28/02/2016

 Nissan Jared Pearson2 (220Pts.)

0

EVO-NIST1 - Shuts down if you don't open the door

Hello, I recently install an EVO-NIST1 on a 2010 Maxima with a Fortin 2-way RF kit. I noticed when testing sitting inside the car, if I remote start the vehicle and press the brake the car will shut off. Pressing the unlock button on the RF remote doesn't seem to help. If I open and close the door the handoff seems to function as intended. Is it necessary for the EVO to see the door pin signal before it will allow the handoff to the vehicle? Is there a setting I can change? Thanks!
Login to reply View 2 answer(s)

26/12/2015

 Ram Darren Asuncion (920Pts.)

0

2014 Ram 1500 Tradesman shuts down on key takeover.

I just recently installed a Crimestopper LCPro-4 with an EVO-ALL interface module on my brother-in-law's 2013 Ram 1500 Tradesman. The installation and programming all went smoothly, however I noticed a couple of problems. Problem 1: The truck does not stay running if you remote start it, insert key and turn to the 'run' position, and step on the brake. I double-checked my wiring to make sure everything was connected to the right places. After the truck shuts off with the brake pedal, there's a small delay (1 second) then the instrument panel lights back up. I can also hear relays clicking inside either the Crimestopper or Fortin modules when this happens - I haven't determined which module's relays are clicking, as they are secured together under the dash. Problem 2: I programmed the EVO-ALL with my Flash Link Updater 2 so that we can have driver's door priority unlocking. All of the doors still unlock when the unlock button is pressed on the Crimestopper remote. I've taken a video of these and they are available here: https://www.youtube.com/watch?v=RJZ_paLS0PA For what it's worth - this truck is a Tradesman model. It has power windows/locks/mirrors, but did not come with keyless entry from the factory. My BIL has owned it since new, and the window sticker does not indicate keyless entry as an option or standard feature, either. Any ideas what might be happening? Hope you had a Merry Christmas, and as always, I appreciate the support! Thanks, Darren
Login to reply View 2 answer(s)

26/12/2015

 Ram Darren Asuncion (920Pts.)

0

2014 Ram 1500 Tradesman shuts down on key takeover.

I just recently installed a Crimestopper LCPro-4 with an EVO-ALL interface module on my brother-in-law's 2013 Ram 1500 Tradesman. The installation and programming all went smoothly, however I noticed a couple of problems. Problem 1: The truck does not stay running if you remote start it, insert key and turn to the 'run' position, and step on the brake. I double-checked my wiring to make sure everything was connected to the right places. After the truck shuts off with the brake pedal, there's a small delay (1 second) then the instrument panel lights back up. I can also hear relays clicking inside either the Crimestopper or Fortin modules when this happens - I haven't determined which module's relays are clicking, as they are secured together under the dash. Problem 2: I programmed the EVO-ALL with my Flash Link Updater 2 so that we can have driver's door priority unlocking. All of the doors still unlock when the unlock button is pressed on the Crimestopper remote. I've taken a video of these and they are available here: https://www.youtube.com/watch?v=RJZ_paLS0PA For what it's worth - this truck is a Tradesman model. It has power windows/locks/mirrors, but did not come with keyless entry from the factory. My BIL has owned it since new, and the window sticker does not indicate keyless entry as an option or standard feature, either. Any ideas what might be happening? Hope you had a Merry Christmas, and as always, I appreciate the support! Thanks, Darren
Login to reply View 2 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue