Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

17/07/2024

 FAQ Richard Regalado Jr (180Pts.)

0

PIN Terminal Standards on Fortin T-Harness

Does anyone know what standard pin terminals are used on Fortin T-Harnesses? I was removing a connection at the Evo module and pulled two wires out of the connector. I need to replace the terminals but have no idea the Standard that is used on the connectors. I'd like to purchase terminals to correct the issue. Thank you everyone!
Login to reply View 1 answer(s)

09/10/2023

 Subaru hofs1 (350Pts.)

0

Key will NOT turn off fully nor remove from key tumbler

2023 Subaru Forester Standard Key Base model have Evo-One installed using Sub1 and Sub3 T-Harness etc .... everything works as far as remote start 3x start doors lock unlock etc Issue is key will NOT turn fully off to be removed Both remote started, insert key turn to run OR start car with key like normal can only turn key to accessory position {radio on}.....Need to pull battery terminal to allow key removal.......Remove all Fortin items and car back to normal. Please advise
Login to reply View 2 answer(s)

09/10/2023

 Subaru hofs1 (350Pts.)

0

Key will NOT turn off fully nor remove from key tumbler

2023 Subaru Forester Standard Key Base model have Evo-One installed using Sub1 and Sub3 T-Harness etc .... everything works as far as remote start 3x start doors lock unlock etc Issue is key will NOT turn fully off to be removed Both remote started, insert key turn to run OR start car with key like normal can only turn key to accessory position {radio on}.....Need to pull battery terminal to allow key removal.......Remove all Fortin items and car back to normal. Please advise
Login to reply View 2 answer(s)

04/06/2021

 Mercury Byron Wilhoite (220Pts.)

0

Wire diagram and differnces

I am installig a remote starter in a 2010 Mercury Milan. under regular installationit reads connection 1A,B and under key program 3 0r 2. Can someone explain in better terms what to do. Also it appears i only need the TX and RX hooked up. I thought i needed the can bus high and low hooked up. I have 2 sets of keys both start the car. need some guidance and what connection to use and what page number to follow for proper hookup. installing a EVO ONE remote starter firmware is 1.25 and hardware is 7.0 Bypass firmware is 71.49 and hardware is 4.0
Login to reply View 1 answer(s)

05/01/2021

 Toyota Ken Lewis (210Pts.)

0

What is a "standard key?"

Toyota FJ Crusier 2007, EVO One: THe only trim option is "standard key." I assume that is regular old key. Is that the case. Just making sure as I do not hava a transponder connector but it is on my wiring diagram.
Login to reply View 1 answer(s)

29/12/2020

 Toyota Mazen Qush (130Pts.)

0

T-Harness assembly Type 2007 Camry standard Key

Hi Fortin Support,

What type of T-harness assembly do I need with EVO ONE to install on a 2007 Toyota Camry standard key, also looking to install a RF kit to it.
Would appreciate your great assistance.

Login to reply View 1 answer(s)

13/12/2020

 Acura Darren Martin2 (130Pts.)

0

Immobilizer wire color and pin location do not match diagram downloaded from fortin website.

SL3 - 2010 Acura TL 3.7 - Standard key
Login to reply View 1 answer(s)

08/07/2019

 Ford Robert Smith (130Pts.)

0

2016 F150 XLT Std Key EVO-ALL w/ Fort3 Standalone Mode C1 & D1 Options Good--No Start

I am in the process of installing an EVO-ALL device with a Fort3 cable into a 2016 F150 XLT with standard key.

    The module programmed correctly. The hood is definitely closed. When attempting to remote start using a LOCK, UNLOCK, LOCK sequence the BLUE LED flashes once with each LOCK button press and twice with the UNLOCK button press. After the third (LOCK) button press the LEDs go through a flashing sequence that ends with a pause (no LEDs lit) followed by three quick flashes of the RED LED which I understand means NO TACH.


I verified that options C1 and D1 have been turned ON by doing the following:

    I grounded the A8 pin of the 20 pin connector.  The RED LED did NOT light so option D1 should be on. I momentarily grounded the A13 pin of the 20 pin connector.  The LEDs went through a flashing sequence very similar if not identical to the one that they go through when attempting a LOCK, UNLOCK, LOCK type remote start.  The flashing sequence ended with the same pause (no LEDs lit) followed by three flashes of the RED LED which I understand means NO TACH.

 

Any ideas?

Thanks!

Login to reply View 1 answer(s)

07/05/2019

 Hyundai Brandon Houston (190Pts.)

0

2016 Hyundai accent standard key Blue programming light turns off when I turn the ignition on

When installing the Evo one on my 2016 Hyundai Accent the blue programming light turns off when I turn the car on and the light comes back on when I turn it off have the can wires on the right ones do I need the can wires to use the remote start?What options do I need to change the service number is 002B07144688
Login to reply View 1 answer(s)

20/03/2019

 Ford Geoffry LALAND (160Pts.)

0

What is a standard key mean on a 2014 Expedition

What is a standard key
Login to reply View 1 answer(s)

15/03/2019

 Chevrolet tony tedesco (160Pts.)

0

2013 EQUINOX WILL NOT START

2013 Equinox will not start. EVO-ALL. did the press 5 times programming, unplugged, went to the computer and finished programming. installed back into vehicle. blue light flashes 3 times by pressing lock 3x's, red light comes on steady, blue light briefly comes on. red light flashes roughly 10-12 times. red light stays on, then goes off. yellow light comes on steady and stays on. while all of this is going on the door chimes, door locks, and radio all come on as if the car was going to start. almost forgot to mention i did get the car to start one time. however, it never worked again. service number is 001A06835311. back of unit also says evo ford, evo mazda pre-loaded. is it possible that i was sent the wrong kit? box says equinox on it.
Login to reply View 1 answer(s)

17/12/2018

 Ford Ohmare Qureshi (230Pts.)

0

2018 Ford F150 STD Key with Keyless not working

Hey Guys, I'm trying to install an EVO-FORT3 on my 2018 Ford F150. When I wire it up using the T harness the key programs as it should but when I try to start it with the OEM fob using the three lock method nothing happens. The box sees my lock and unlock commands because I see the blue light flash, but it just doesn't start. When I ground the manual remote start trigger (yellow/black wire) from the EVO-ALL the truck starts as it should. I don't have a cable to check the programming as it was programmed by a dealer. Does this sound like a programming issue? The truck starts when manually triggered, just not with the remote as it should.
Login to reply View 2 answer(s)

17/12/2018

 Ford Ohmare Qureshi (230Pts.)

0

2018 Ford F150 STD Key with Keyless not working

Hey Guys, I'm trying to install an EVO-FORT3 on my 2018 Ford F150. When I wire it up using the T harness the key programs as it should but when I try to start it with the OEM fob using the three lock method nothing happens. The box sees my lock and unlock commands because I see the blue light flash, but it just doesn't start. When I ground the manual remote start trigger (yellow/black wire) from the EVO-ALL the truck starts as it should. I don't have a cable to check the programming as it was programmed by a dealer. Does this sound like a programming issue? The truck starts when manually triggered, just not with the remote as it should.
Login to reply View 2 answer(s)

20/10/2018

 Ford Karol Kipirzepa (140Pts.)

1

15 Ford Fusion standard Key will run only for 10 mins no matter what I set it to.

2015 Ford Fusion Automatic Standard Key Stand alone I have Evo All hardware ver 6 software 4.01 It will run only 10 mins even if I will set it to 30 in diesel mode. I updated the software to 4.02 like recomended by the flashlink but than my car will not start at all so I went back to 4.01 and same 10 mins at 15 set. Please advise.
Login to reply View 2 answer(s)

24/10/2018

 Kia Justin Chang (690Pts.)

0

Can RF kit be used with EVOALL on 2013 Kia Optima Std Key?

Under "required technology" RF kit is on EVO ONE but not EVO ALL. Does that mean a RF kit can't be used on my 2013 Kia optima that uses standard key?
Login to reply View 2 answer(s)

29/10/2018

 Ford Amit Gajjar (690Pts.)

0

2005 Ford Explorer with only 1 Standard 80 bit key

Hi I know when you filter remote start solutions for 2005 Ford Explorer Std Key, it says 2 keys required for programming but when you go into guide I see options for 1 key under same year. Customer only has 1 key so I wanted to know if you there is a solution for owner?
Login to reply View 1 answer(s)

24/10/2018

 Kia Justin Chang (690Pts.)

0

Can RF kit be used with EVOALL on 2013 Kia Optima Std Key?

Under "required technology" RF kit is on EVO ONE but not EVO ALL. Does that mean a RF kit can't be used on my 2013 Kia optima that uses standard key?
Login to reply View 2 answer(s)

20/10/2018

 Ford Karol Kipirzepa (140Pts.)

1

15 Ford Fusion standard Key will run only for 10 mins no matter what I set it to.

2015 Ford Fusion Automatic Standard Key Stand alone I have Evo All hardware ver 6 software 4.01 It will run only 10 mins even if I will set it to 30 in diesel mode. I updated the software to 4.02 like recomended by the flashlink but than my car will not start at all so I went back to 4.01 and same 10 mins at 15 set. Please advise.
Login to reply View 2 answer(s)

06/10/2018

 GMC Matthew Reed (130Pts.)

0

Standare or Standalone?

service number 001A06 556424 2016 GMC Sierra 2500 Diesel, automatic, standard key, ON-Star I have the EVO-ALL module and the GMT-3 harness. All seemed to go well on the install but have questions and ready to put the firmware in and do programming. 1.Document indicates Lock/Unlock wires not needed with On-Star. Advise. I've only connected parking lights and CAN-BUS line. 2. When selecting firmware, I get standard or stand-alone question. Unsure of the difference. Also - what is the CORRECT document I should be looking at for following the complete installation for my setup. Thanks! Matt Bettendorf, IA
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue