Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2010 Lexus RX 350 – EVO-ALL Stand Alone with ASCL6 CARLINK: Remote Start Not Working ( NO IGNITION, NO CRANK)

Issue: Remote start does not work when initiating the remote start command via factory remote (3X lock) and/or CARLINK App.

A few things that I noticed when trying to remote start the car:

    The transmitter and CARLINK app are communicating with the EVO-ALL - when the remote start is initiated, the blue LED on the EVO flashes once and a solid red light illuminates after.  During this time, no lights on the cluster/dash turns on and there is no crank.The EVO attempts this process again with the same results. After the second failed attempt, the red LED on the module and the car’s parking lights flashed 3 times.  Next, I tried remote starting the vehicle using the idle mode. 
      I started the car by stepping on the foot brake and pushing the START/STOP button.  Once the car was running, I activated the remote start with the CARLINK app.The remote start count-down timer appeared on the CARLINK app which tells me that the command was sent, and the module is in the remote start mode.I stepped out of the vehicle and the dash screen notified me there was no key (car remained idling)CARLINK app still showed the count-down timer for the run time.I deactivated the remote start using the CARLINK app and the vehicle turned off.

I also checked to see if all the other commands were working properly by using the CARLINK app.

    Lock/unlock doors – good.Open/close back trunk/door – goodParking lights – goodVehicle lock and unlock status - good, shows on the app when the doors are locked or unlocked. Battery voltage shows on app, (13V)

I’ve doubled and TRIPLE checked the wiring, making sure they were terminated as shown in the installation guide (GUIDE # 77041) and that all connections were secured.

I don’t know if I am having issues with the installation or programing. I tried resetting the evo and re-flashing it and also down-grading the firmware to 79.66 to match the firmware on the guide. I think I might have tried a different firmware version as well (in between 79.70 and 79.66) with no luck. I eventually got locked out of the EVO-ALL because the flash limit was reached. I ended up ordering a second EVO-ALL to started from scratch again and I encountered the same problem.

I confirmed that the car does not have a factory remote starter by pressing the factory remote Lock button 2X and holding it after;  the car did not start. Furthermore, I removed the glove box to check if a factory remote start was present, and as far as I can tell, I did not see one. The location of the factory remote starter was referenced from an Automotive Data Solutions Inc. (FLCAN and ALCA TL2) installation guide. If you have more details about where else this might be, please let me know and I can check again.

Please HELP! What should I check next?

Here are some details about the EVO-All that is currently installed.

     Manf Date: 04/2023  SN: 001A07499141Firmware Flashed: 79.70Hardware Inside 7.0 Setup Configuration
         *** SETTING PROTECTION = OFFA1-A11 = ONA12-A14 = OFF B1-B3 = OFFC1 = OND1 = ON
          D1.8 = ON D1.10 = ONAll other D1.X = OFF D2-D5 = OFF (Guide shows D4, Hybrid Mode- do I need to turn this on?)
      D6 = OND7 = OFF SPECIAL FUNC = ALL OFFDATALINK PROTOCOLS = ALL OFFG = ALL OFF  H SUPPORTED RF KITS = ONH2 = ON
    Wire Connection (connected according to diagram):
      A8: Not connected - vehicle is equipped with factory hood pin so that status is provided via can bus, correct?

0

2014 Audi RS7 EVO ONE with Carlink ASCL6 4G

What remote start firmware should I used if I am adding a ascl6 carlink to my Evo-One?

0

EVO-ALL and CarLink CL6 Wiring

I installed EVO-All using THAR-For4. Then i added Carlink CL6 into it. Remote start stop, battery health, and gps features worked right away with no issues but Carlink App also has 4 Auxilary options, heated seats options and lock/unlock options. I read on Fortin that my THAR-For4 shuold be enough to use lock/unlock feature on CL6 but it does'nt work, So I guess I have to open the kick panel and split wires there. I paid $5 for wirecolor.com subscription token to see if I can find wiring help but its created by a 5 years old so thats ok. My question here is how to I connect heated seats to EVO-All and is there any way to add climate control to one of those auxilaries showing in the app (add it to evo then use auxialry to control it). If I can get wire colors and location of wires I can work with that. Thanks P.S. I have evo flash tool and I checked my lock/unlock options are on in the Evo-All settings.

0

CL6 / Evo-One - Not Communicating?

 

Reposting because, well, the first thread will never been seen again and the answer missed important points

 

Please read the whole thing.

 

Eclipse Cross, 2018, SE

Latest firmware for starter and bypass. Loaded recommended options and confirmed the options specified in the setup PDF for the car were set. Using the MITS2 harness.

3x lock works for remote start works.

Tried various (3?) methods of syncing, all of which seemed to work, however, device still only shows it's own information (battery voltage, GPS, and "connected" icon)

Yes, using the crossover cable. Yes using the right port on the evo-one (blue).  

Tried sending the unlock command/lock command at the last steps of the sync. Door open and door closed. Didn't seem to matter. 

Tried switching the protocol in the app to something else then back to Fortin.

Confirmed the "datalink" protocol is Fortin 2  

Previously, this carlink was used with an evo-all for a different car and it worked great. Now it does not. 




 

0

ASCL6 / Evo-One - Eclipse Cross 2018 - No unlock/lock/start/etc

Eclipse Cross, 2018, SE Latest firmware for starter and bypass. Loaded recommended options and confirmed the options specified in the setup PDF for the car were set. Using the MITS2 harness. 3x lock work for remote start works. Can't seem to get the Carlink and Evo-One to communicate. Tried various methods of syncing, all of which seemed to work, however, device still only shows it's own information (battery voltage, GPS, and "connected" icon) Using the crossover cable in the CL6 instructions and confirmed correct port on evo-one. Tried the valet switch sync, the on-off-on sync, the unplug, red/blue sync Tried sendin the unlock command/lock command at the last steps of the sync. Tried switching the protocol in the app to something else then back to Fortin. Confirmed the "datalink" protocol is Fortin 2 (there are no other options other than the FMH) I have found a thread or two describing a problem just like this, but those solutions were mostly about not using the correct crossover, having the learn procedure not working as expected, so they weren't relevant to me, sadly. Previously, this carlink was used with an evo-all for a different car and it worked great. Recently resubbed after a year to use in the Cross and have spent the better part of a week trying to figure this one out. Tried all of the procedures in the programming FAQ as well as the workarounds. The procedures, each different type, all seem to work correctly, but the behavior never changes. Evo-one still unresponsive to the carlink. Really wondering at this point if the ascl6 can do anything without splicing more wire / whether it's a bug / or ? At a loss on this one. At the last step of syncing (turning the car off), the red/blue flash 4 times. Can't seem to find a diagnostic for what this means.

0

Add ASCL6 with RFK942

I've installed the EVO ALL with T-Harness (EVO NIST4) and the RFK942 RF kit to my 2016 Infiniti Q50 (3.0T). All works well. I am considering adding the Car Link ASCL6 system to my car. My question is can I use the RFK942 together with the Car Link or will I have to choose between one or the other If I can use both, will I need something added to the existing T-Harness (EVO NIST4) in order to connect them both (such as RFA2A)? Thank you in advance for your help.

0

FAQ: Programming CARLINK, ASCL6, LINKR, MYCAR

To program your carlink,
    make sure to follow their instructions on how to connect it to the EVO-ALL or EVO-ONE using their own HRN-LLRS-01 harness setup the app for fortin follow programming in car
     

Here is a copy of their guide. Please read attentively every step of programming since their is setup in the app you must first do. https://fortin.ca/download/64631/ascl6-install-guide-64631.pdf

  EVO-ONE Programming
  Following the RED LED on the BACK of the unit, not the one on top.  
    Igniton ON-OFF-ON  (red led on evo will turn on solid) Hit brake 4 times (red led will flash on each brake press) At this point wait 10 seconds then shut off the car.

 

EVO-ALL Programming

Please first try the EVO-ONE. It was added to the EVO-ALL firmwares. 

Otherwise, this older method is still functional.

    Disconnect the 20-pin connector Disconnect the 4-pin black connector Press and Hold programming while inserting 4 pin connector.  Release when the LEDs are BLUE and RED Press and HOLD programming button, wait until the BLUE and RED LEDs turn and then BACK ON. Release when they turn back ON. Plug in 20-pin connector Turn ignition ON, all three LEDS will turn ON Wait 10 seconds, then turn off ignition. 

0

Evo all & ascl6 program issue

2014 ram 1500 (standard key start) after successful programming, vehicle can be remote started by 3x lock only....H2 - fortin 2 is selected on in flashlink setting, ascl6 app protocol is set to fortin, RFA2A adaptor is connected but still no luck, both red and green led on ascl6 are on solid, been trying to get the evo all to pair with ascl6 with no success.

 

evo all led lights are stuck at step 8, will not go to step 9 

1 - Disconnect the Black 4 pin power connector from the Evo-All.

2 - Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.

3 - The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED and BLUE LED’s are On.

4 - Release the programming button.

5 - Press and Hold the programming button again for 5 seconds. The BLUE and RED LED’s will blink once.

6 - Release the programming button.

7 - Cycle the ignition to the ON position.

8 - The RED, YELLOW and BLUE LED’s will be ON.

9 - Seconds later the RED and BLUE LED’s will blink once to confirm that the MyCar ID has been learned to the Evo-All.

10 - Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming.

0

Adding Carlink to EVO-ALl

I have a preinstalled evo-all on Mazda6, we need to add carlink, I will need to add telematic option and learn carlink to EVO-all. will we need to redo keybypass programming procedue after we learn carlink to evo-all.

0

Carlink ASCL6 EVO-ONE HOW TO LOCK AND UNLOCK DOORS

Hi, I have installed EVO-ONE AND ASCL6 Carlink on my 2018 Subaru Outback Limited Push to Start , everything works the Carlink does remote start and shutoff the vehicle, but it won't open or lock the doors. Do I need to connect additional wires for it to be operational or program EVO-ONE in a Flash Link app?

0

carlink cl6 and evo all

i have toyota camry 2014 G-key and Crimestopper RS00 how to connect cl6 and what option should be on? thanks

0

how to setup car link BT Long Range ASCLBTLR to evo All

Hi I need configure set up the car link BT long range 2 way control with smartphone control ASCLBTLR it has evo All in the setup but it is blank. i looked on carlink.com for setup and spoke to lesco and they said to contact fortin. i have everything set for the wiring to the 2008 ford f 150 for the evo all to the crimestopper rs4 g5 remote start unit. i need to all this remote the evo all so the long range remotes work thanks Steve

0

Is Evo-all compatible with Audiovoxx's bluetooth version of Car Link, model ASCLBTLR?

I see that it's compatible with the cellular Carlink, model Ascl6 from audiovoxx, but the bluetooth version wasn't on the list. Don't know if the list hasn't been updated yet or it's just not compatible for some reason.

16/02/2020