Questions & Réponses

I am looking to install the EVO-All with the THAR-MAZ1 t-harrness in standalone configuration in a 2014 Mazda 3 (push-button automatic), and the installation guide states that 2 key fobs are required to programm the evo-all, however I only have 1 key fob.

I want a confirmation whether the evo-all can be programmed successfully with a single key fob, and clarification on what that process would look like? Should I simply skip the steps for the second key fob or follow the steps using the first key? 

Installation Guide page 8: https://cdn02.fortin.ca/download/62681/evo-all_ig_tsa_bi_maz1-3_pts_2014-2017_door_v2_e_62681.pdf

2012 Audi S4

I just programmed 2 new remotes to Nano Start V3, old remotes lost and unknown if system was working previously.

New remotes confirmed programmed and will LOCK / UNLOCK / TRUNK.

LED on antenna is flashing.

When pressing "START", the door locks cycle and dome light comes ON pause  door locks cycle again. pause alarm chirps and hazards flash then doors cycle again. pause door locks cycle again. pause alarm chirps and dome light goes out. pause

LED on antenna is flashing whole time for operation and continues to flash after, also good to mention the OEM Audi fob is more than 10meters away from vehicle..

I'm not sure if I messed something up programming the key fob but seemed simple enough - Key ON/ hold button till LED flashes and release / press button once / press brake / press LOCK button on 2 new fobs / press brake / key OFF. Tested both remotes and confirm programmed..

What am I missing?

2012 Audi S4 push button start DSG.

Lost the remote fob and need to replace (lost in transit when railing car from montreal to outwest). Car is from Montreal but recently moved to British Columbia, closest distributer is 5 hours away.

I accessed the module under dash, it's a Nano Start, Hardware V3. Firmware V10.17.

I have the installation manual to program the unit not sure of which remote and where to buy online,

What's the model# for the fob replacement? Is there a place to order the remote fob online?

(Also can this nano start have something added to use the oem key to 3x-lock-start?)

Fortin website comment on EVO-ONE : "The module will monitor the OEM remote for 3X Lock and will start or stop the automatic transmission vehicle through High Power Outputs or data." and "Pressing the LOCK button 3 times (3X Lock) on the OEM remote will activate or deactivate the remote starter. "

=> But my car - 2014 RAV4 only start, but cannot stop by 3x Lock button.

Thank you,

Est-ce que je pourrai debarrer les porte en utilisant ma manette OEM ? ou devrais-je utiliser la cle proprement dit?

La télécommande d’origine du véhicule sera fonctionnelle pendant que

le véhicule est en marche, toutefois, le déverrouillage des portes par la

clé d’accès Intelligente ne sera pas fonctionnel.

Hello,

Can I drive my car (not remote start) without  OEM key? if I nstalled

1- EVO KEY or,

2- EVO ALL or,

3- EVO ONE.

After installing a Prestige APS787E alarm w/ my Evo-All bypass module on my 2012 Nissan Rogue (Non-Push2Start), my lock, unlock & trunk buttone on the aftermarket keyfob work but the remote start doesn't work. I updated my Evo-All to the latest firmware & hardware available & flashed it to D2D protocol.

I also programmed the Prestige alarm using the install guide to get the Tach signal via D2D mode. But when I attempt to follow the "Tach rate progarmming" section of the manual, it is clear the alarm might not be getting a tach signal.

Is it possible to hardwire the tach signal to my alarm while using data mode w/ the Evo-All?

Secondly, I test the "ground while running" wire connection btw the Evo-all & Prestige alarm with a multimeter and I get a constant 12V even when trying to remote start. Is this normal? I thought it would/should give me a 0V or ground signal when I attempy to remote start the car.

Lastly, also just noticed that my Prestige key fob arms the aftermarket alarm but locking my doors w/ the OEM Nissan keyfob doesn't. Thus when I arm the car w/ the Prestige keyfob & unlock & open the doors w/ my Nissan key, the siren goes off. Is this normal?