Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Nissan Frontier factory fob 3x lock to start?

Is there a special process for enabling lock x3 to start for a Nissan frontier? It's offered by competing remote start vendors (probably using Fortin system). I found a guide for enabling via Link software 3x lock to start but the NIS5 guide does not mention it. If enabled via link app in the module, is that all that needs to be done alongside the wiring instructions? The module should have the inputs internally to work it out from what I can see in the diagram. It would be down to the module logic which I don't know the details of.

0

Need help selecting an alarm for 2019 Nissan NV 200 Cargo Van

Hello Tech Support, I am in need of your help, kindly assist me with select an alarm that will be Plug and Play for my 2019 Nissan NV200 Cargo Van. I would like to have 4 buttons on the remote ( Cargo door, unlock , lock and remote Start/panic), remote start can also be accepted. Thank you in advance. My email is markwilkinson805@hotmail.com

0

2021 Nissan Rogue power rear hatch

2021 Nissan Rogue with the power rear opening hatch , when installing the evo all and RFK942 remote the power hatch requires a 3 second hold on the switch in the car compared to the monetary push with the base model , is there a way to program the evo all to to instead of a momentary ground on the hatch realease to hold the ground for 3 seconds

14/10/2023

Nissan G M (14940Pts.)

0

2010 nissan patrol

Hello. For a 2010 Nissan Patrol (Euro), which instructions will work? And the firmware? StandAlone.

0

FORTIN RFK411

Hi, again before 5 months i have installed EVO-ALL with NIST1 on Murano 2009. I can start the car wirh OEM FOB (3xLOCK) but can not stopped it or unlock it with the FOB. It can unlock it with the phisical key and when oped the the door the engine stopped. I had done connections to the BCM module(LOCK/UNLOCK pins). Now i have installed Fortin RFK411. I can start and stop the engine but still can not unlock the car when engine is remotely started. I can not lock or unlock the cars when car is NOT started with Fortin remotes. I have one question- if i make connections for LOCK/UNLOCK not to BCM, but directly to the drivers door button for LOCK/UNLOCK. Please make advise!

0

What's all the accessories I need to connect a Fortin EVO-ALL to 2012 Nissan Pathfinder Standard Key

0

2022 Nissan kick check engine light

I installed a evo all stand alone with a rf kit on a 2022 Nissan kick everything works but the check engine light came on some communication codes faulty gas gauge and other things, I got it erased but every time I remote start the car it comes back on if anyone knows how to fix please let me know thanks

0

2012 nissan versa fortin one t harness can it use the 3x lock feature.

2012 nissan versa sedan,using evo one and t harness how do i know if the 3x lock feature will work on this or can only use the long range remotes.Is there something that tells you which cars can take the 3x lock feture?

0

Nissan Versa 2019 Standard Key Installation Help

Hi there, I am wanting to install a remote starter into my vehicle and want to confirm that it would be possible for me to do so. I looked at the vehicle finder and saw that the Versa wasn't avaible in the year 2019 so i was just going to flash the modular for a 2018 instead. Since there is no connection diagram for the 2020 standard key to reference to from the 2018. I looked at the diagram for a 2019 nissan versa note and 2018 Nissan Versa both standard key. My car doesn't have a transponder and i would assume that during the programming i would insert the white big 8 pin connector while pressing the program button, letting go on blue. Insert all remaining connectors, put the key to the run postion let the blue leds flash and once it stops flashing remove they key. 2018 Nissan Versa Install Diagram https://fortin.ca/download/79341/evo-one_ig_thr_bi_nis5-versa-sedan_2012_key_a_79341.pdf 2019 Nissan Versa Note Install Diagram https://fortin.ca/download/79331/evo-one_ig_thr_bi_nis5-versa-note_2014_key_a_79331.pdf

0

EVO All, THAR-NIS3, X-Trail(Rogue) Push to Start 2016

Hi, I have installed EVO All with THAR-NIS3 (had to extend the OBD wiring as my car is RHD and the BCM is on the left passenger side.) Everything worked during install per the instructions including the decrypter (used the Rogue 2016 Push to start as the ref.) Selected Diesel. OEM Alarm First time the car just cranks and doesn't start(3xlock press) - the (factory) alarm goes off (have to press unlock on remote to stop the alarm) Second time the car starts (3xlock press) but thats it if i try again it doesn't work(cranks but doesn't start) Model - EVO-ALL DATE 07/2021 SN 001A07273507 I know it is a bit of stretch but keen to get it working before winter sets in. Appreciate any support on this

0

2013 sentra push to start fix is to connect white/black wire from where to which wire exactly?

I read a previous post about a nissan being wired with pre-assembled harness and EVO-ALL on 2013 push to start sentra ... and brake lights and start button light up but nothing starts...The red light on controller flashes 3 times after it tries to start.The fix was connecting the white/black wire from 19 pin connector to push to start button..I just need some guidance as to where exaclty does the white/black wire come from and where exactly am I supposed to connect it? I`m not a tech,just a guy who bought a plug and play remote start on ebay.Any help is appreciated..

0

How to connect D4 D6 , 2006 Nissan Altima

I'm using evo-one with niss2 harness for my 2006 Nissan Altima I am confused about the connection D4 and D6 showing guide #78211. I also don't know where to connect the pin 30 from the relay for parking lights . A picture would be great, or can I leave the parking light unconnected? The last question, do I have to have a RF module to remote start? Because when I put my key at on position, the blue lights went off.

0

2016 nissan versa, can't find a guide for a non transponder key.

0

EVO ONE 2011 NISSAN XTERRA W/GUIDE 79461, WRONG CONNECTOR

PAGE 3 OF GUIDE, BALLOON 5- BMC IS NOT BEHIND GLOVE BOX. BALLOON 2- CONNECTOR ON T HARNESS IS NOT CORRECT FOR TRANSPONDER BALLOON 3- CAN'T FIND CONNECTOR IF I GET THE ABOVE ISSUE ANSWERED, WILL MANUFACTURES REMOTE 3X LOCK WORK?

0

have to push the pts button several times for 2015 nissan altima to turn off

im installing a evo-all nisa4 t harness in my 2015 nissan altima. it will start with the remote start oem fob but after getting in the car to shut the engine off/on you have to press the pts button several times for it to do anything. what am i missing?

0

2007 Nissan Altima red light flashing 3 times when trying to start

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.

0

Evo-all and compustar rf remotes

Hi i bought a evo-all and a compustar 4900s and after trying to install the compustar system to the evo-all and had no luck, I decided to to see if I could just use the remote and antenna with the evo-all rather then the compustar remote start. And if its possible to just add the antenna and remotes to the evo. How would one go about doing that?

0

2007 Nissan Altima red light flashing 3 times when trying to start

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.

0

2007 Nissan Altima red light flashing 3 times when trying to start

I have completed the install and programming everything seems to be done correctly. I did not connect the 3 wires to the bcm foot lock unlock and door pin because I don't want to. When I hit the lock button 3 times the unit clicks and attempts to start but then red light flashes 3 times and doesn't start.

0

{2015 Nissan Altima} Only way to stop engine is to press start/stop button on dash 3 times.

After installation of Evo, the only way the car turns off is by pushing the start/stop button on the dash 3 times. It no longer shuts off by just pressing it once. This occurs when the car is started with the fob (lock lock lock) and it also happens when the car is started traditionally with the start/stop button on the dash. Why???

0

Programming issue

I have 2009 Nissan Versa So after connecting all the wires I reached the programming part when I hold the programming bottom to connect the main harness it start changing the led color rapidly and even if I release the bottom it keep changing the led color and never stop until I disconnect the main harness is it something has to do with flushing the module or the wiring

0

Will this work with a 2013 Nissa Versa with Manual Transmission?

Will this work with a 2013 Nissan Versa with a standard transmission? I noticed that most of your instruction sheets have a section for compatible vehicles that have a manual/standard transmission but I do not see that with this vehicle. Regular Key start.

0

EVO-ALL THAR-NIS1 Nissan Sentra 2015 Push-To-Start doesn't start

The steps I followed: - Plugged the 4 pin back of push to start button - Plugged the 4 pin break pedal - Plugged the 16 pin OBDII After plugging those connectors I went with the key bypass programming procedure. Pushing the lock key 3 times makes the module send commands to the car, but no success turning it on. And then the red light flashes a few times (if I'm not mistaking it's 3 times). I did not connect those 5 other wires into the BCM, Driver kick panel or Push-To-Start Button because I thought that only connecting the plugs would be enough to get the vehicle started. Is this assumption right or I should connect all those other 5 wires to get the car started? The following file is the installation guide so you guys can take a look and help me on it: https://fortin.ca/download/74261/evo-all_ig_tsa_bi_nis1-sentra_pts_2013-2018_a_74261.pdf

0

everything was working now its not starting

i just installed an evo one on 2012 nissan versa standard key.im using nis5 t harness with rf442. i installed all the wire except the door lock/unlock vehcile was remote starting with delay the ignition instrument panel lights turn on and click turn off start second time it would start .i removed the evo ground and now when i try to start i see red light flash and hear clicking from evo one with no sucessfull start please help.lock un lock wires are still not connected. im not using door pin and hood pin wire which are grounded to chasis.

0

rf kit program setting, door unlocking

what setting do i need to enable to install RF442 on 2014 nissan versa with standard key.im using t harness thar one nis5. how do i program the rf kit and do i need to connect pin a1 to pin a8 if i dont want to use rf kit to unlock or lock just need remote start.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer