Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Can't find lock/unlock wiring

Working on a 2010 Chevy Traverse, photos show the pink and orange wire at the Bcm but it this situation those wires aren't there, I try to find some others but can't yet.. Evo RS4

0

Do D6 and D3 only read ignition?

On the evo one are d6 and d3 only for starting the car with key? The immobilizer amplifier is fried and it seems they go on the ignition side after the cut wire so im wondering if they are necessary or if i can get away with putting them blank. Any information or thoughts would be awesome.

0

how do i wire up the door unlock so i can gain access to the car after remote started

I see that in the evo model their are wires to lock and unlock the doors for a 2014 Hyundai Santa Fe with Key start, however i cannot find any info on where to connect the unlock wire from the evo starter to the car so that i can unlock the doors after remote starting it.

0

how do i find the loacation of the TX and RX wire in a toyota prius v 2013

I"m installing a remote starter on my toyota prius V 2013. I have downloaded the install guide from idatalink.The pin location of the Tx and Rx and parking light wires shown on the install guide are not the same as in the car itself. The colors do match, but as i said the pin locations are different. What do i have to do in this case?

0

Where does wire D1 go at the "Cut"?

On a Kia Sorento 2019, it says cut wire at D1. Where does the wire (D1) go after cutting it? Theres also dotted lines in between.. Im guessing it connects to the other wires (D3/A10) towards the connector? This is for a Kia Sorento 2019 push to start and evo one regular installation.

0

Can I trim the extra wires from my THAR once installation is complete?

I have a 2016 Mazda 3 doing a stand-alone install with a T-Harness. Following the guide: http://cdn02.fortin.ca/download/62681/evo-all_ig_tsa_bi_maz1-3_pts_2014-2017_door_v2_e_62681.pdf. Once completed, I will have only connected A8 and A20 directly from the "A" connector. Can I cut the other wires from the A connector for a "cleaner" installation? Obviously I would leave A1, A10, A19 because those are fed from the t-harness connections. Also, if I have no plans of adding an RF kit, can I cut/remove the white & blue wires on the "B" connector as well as the "extra" red and black wires leading to the RF kit? Like I said, just trying to make the cleanest install I can.

0

cutting the right wires

Using the evo-ride bypass for my 2004 Toyota Camry and just want to make sure I read the diagram right. I am supposed to cut the IMI cable(yellow) into two and splice the white/red from the 3 pin conn. to the connector side of the IMI wire. While the yellow/black from the 6 pin conn. and the white/green from the 3 pin connector gets spliced into the car side of the IMI wire. Correct me if I'm wrong. Thanks.

0

what wires are required for evo- fort1 regular installation w/ t harness 2015 focus

What wires are required for evo- fort1 regular installation w/ t harness 2015 ford focus SE..

 

 

0

required connections for remote start only

2011 ford escape automatic using standard key for remote, what are the only connections i need (or what connections dont i need) to allow the remote start function to work. i know i need the hood and valet for safety. i have the evo RS evo-fort1 (t harness) preloaded all in one universal data bypass and interface module evo-all and following 32171 schematic

0

Twenty pin connections

I have installed T-harness and can high and low . Their appears to be four wires on the 20 pin that connect to the T-Harness. Do I still need footbrake , tach & hood switch for the remote start to work. Just asking for clarification please . Thanks. Using EVO-All with FORT 1 .

23/01/2017

Ford CBB (200Pts.)

0

CANBUS Remote Start

Is it possible to trigger a remote start through the CAN-BUS (HS-CAN or MS-CAN)? 2012 Ford Fusion. Goal is to use a ELM327 OBDII Bluetooth adapter (modified to include MS-CAN) and an Android phone, sending a request to the CAN-BUS that would trigger the remote start (or the EVO-ALL). I know I could tie into the Yellow/Black wire off teh EVO-ALL and feed it negative but that would require me to include a relay system in between that I would like to avoid. Any assistance is greatly apprectiated.

0

2014 FORD ESCAPE MIN./ MANDATORY CONNECTIONS FOR REMOTE START ONLY

What are the minimum / mandatory connections for remote start only option on 2014 Ford Escape with T harness, and minimum flashlink options. The lock-lock-lock function does nothing. the lock-unlock-lock sequece will turn on the ignition, but not start. Just wanted to do something nice for my daughter that appeared to be a short project, and now a 5 hour ordeal. Don't want to cut or splice any wires I do not need to.

0

What Extra wires no need to be connected (Mandatory)? FORD EDGE 2013

I am trying to install my EVO into my Ford EDGE 2013, according the manual athttp://fortin.ca/download/34421/evo-all_ig_tsa_bi_for1-80bits_c_34421.pdf, and I am having a problem, so I have some questions if you don't mind in answer please:

1) I am wiring only the connections for CAN high and Low (C3 and C4), and A1, A20 and A10 to the 20 pin connector ( not wiring/connecting A17, A18,A5, A19, A8, A14 and Parking lights). It should work with these connections out or they are not optional?

2) Manual shows Yellow/BLACK wire to be connected to YELLOW ( not yellow black) into 20 pin ( is that correct?)

3) I am able to proceed with all programing steps and leds as shown in the manual, but when I Press Lock 3x, nothing happens, the engine does not start. Am I missing some mandatory connection?. What are the mandatory and optional connections in this schema ?

 

 

 

12/12/2016