Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

02/12/2018

 Ford Mark Obsniuk (280Pts.)

0

what wires are required for evo- fort1 regular installation w/ t harness 2015 focus

What wires are required for evo- fort1 regular installation w/ t harness 2015 ford focus SE..

 

 

Login to reply View 1 answer(s)

24/12/2017

 Ford Sheaffer Hawk (190Pts.)

0

required connections for remote start only

2011 ford escape automatic using standard key for remote, what are the only connections i need (or what connections dont i need) to allow the remote start function to work. i know i need the hood and valet for safety. i have the evo RS evo-fort1 (t harness) preloaded all in one universal data bypass and interface module evo-all and following 32171 schematic
Login to reply View 0 answer(s)

03/03/2017

 Ford Dale Holden3 (160Pts.)

0

Twenty pin connections

I have installed T-harness and can high and low . Their appears to be four wires on the 20 pin that connect to the T-Harness. Do I still need footbrake , tach & hood switch for the remote start to work. Just asking for clarification please . Thanks. Using EVO-All with FORT 1 .
Login to reply View 1 answer(s)

23/01/2017

 Ford CBB (200Pts.)

0

CANBUS Remote Start

Is it possible to trigger a remote start through the CAN-BUS (HS-CAN or MS-CAN)? 2012 Ford Fusion. Goal is to use a ELM327 OBDII Bluetooth adapter (modified to include MS-CAN) and an Android phone, sending a request to the CAN-BUS that would trigger the remote start (or the EVO-ALL). I know I could tie into the Yellow/Black wire off teh EVO-ALL and feed it negative but that would require me to include a relay system in between that I would like to avoid. Any assistance is greatly apprectiated.
Login to reply View 1 answer(s)

12/12/2016

 Ford Francisco Ribeiro (130Pts.)

0

What Extra wires no need to be connected (Mandatory)? FORD EDGE 2013

I am trying to install my EVO into my Ford EDGE 2013, according the manual athttp://fortin.ca/download/34421/evo-all_ig_tsa_bi_for1-80bits_c_34421.pdf, and I am having a problem, so I have some questions if you don't mind in answer please:

1) I am wiring only the connections for CAN high and Low (C3 and C4), and A1, A20 and A10 to the 20 pin connector ( not wiring/connecting A17, A18,A5, A19, A8, A14 and Parking lights). It should work with these connections out or they are not optional?

2) Manual shows Yellow/BLACK wire to be connected to YELLOW ( not yellow black) into 20 pin ( is that correct?)

3) I am able to proceed with all programing steps and leds as shown in the manual, but when I Press Lock 3x, nothing happens, the engine does not start. Am I missing some mandatory connection?. What are the mandatory and optional connections in this schema ?

 

 

 

Login to reply View 3 answer(s)

12/12/2016

 Ford Francisco Ribeiro (130Pts.)

0

What Extra wires no need to be connected (Mandatory)? FORD EDGE 2013

I am trying to install my EVO into my Ford EDGE 2013, according the manual athttp://fortin.ca/download/34421/evo-all_ig_tsa_bi_for1-80bits_c_34421.pdf, and I am having a problem, so I have some questions if you don't mind in answer please:

1) I am wiring only the connections for CAN high and Low (C3 and C4), and A1, A20 and A10 to the 20 pin connector ( not wiring/connecting A17, A18,A5, A19, A8, A14 and Parking lights). It should work with these connections out or they are not optional?

2) Manual shows Yellow/BLACK wire to be connected to YELLOW ( not yellow black) into 20 pin ( is that correct?)

3) I am able to proceed with all programing steps and leds as shown in the manual, but when I Press Lock 3x, nothing happens, the engine does not start. Am I missing some mandatory connection?. What are the mandatory and optional connections in this schema ?

 

 

 

Login to reply View 3 answer(s)

12/12/2016

 Ford Francisco Ribeiro (130Pts.)

0

What Extra wires no need to be connected (Mandatory)? FORD EDGE 2013

I am trying to install my EVO into my Ford EDGE 2013, according the manual athttp://fortin.ca/download/34421/evo-all_ig_tsa_bi_for1-80bits_c_34421.pdf, and I am having a problem, so I have some questions if you don't mind in answer please:

1) I am wiring only the connections for CAN high and Low (C3 and C4), and A1, A20 and A10 to the 20 pin connector ( not wiring/connecting A17, A18,A5, A19, A8, A14 and Parking lights). It should work with these connections out or they are not optional?

2) Manual shows Yellow/BLACK wire to be connected to YELLOW ( not yellow black) into 20 pin ( is that correct?)

3) I am able to proceed with all programing steps and leds as shown in the manual, but when I Press Lock 3x, nothing happens, the engine does not start. Am I missing some mandatory connection?. What are the mandatory and optional connections in this schema ?

 

 

 

Login to reply View 3 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue