Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Solid yellow and red light

So im installing the evo all with the tb-vw module in a 2008 vw rabbit. ive been fighting with this thing for a few hours now trying to get the thing to read the key so i can use the dcryptor. ive manage to get past the setup 3 diffrent times but each time i end up with a solid yellow and red light when i apply power back to the evo all. when i go to start it, the yellow will go off then the red starts flashing and wont stop till i unplug it. any advice would be great. also ive tried factory resetting, flashing diffrent firmwares and ive now hit the limit on dcryptor and i believe im one flash away from the limit

0

All 3 LEDs on EVO-FORT4 with first key in

2014 Ford Flex Std. Key w/EVO-FORT4 Soon as the fist key is inserted all 3 LED's stay lit solid...even all through 2nd key and back to the 1st key during programming. Vehicle can be put in 3rd key programming mode without module installed (door locks will cycle). Key sense wire is good, ignition chime comes on when key is inserted. Tried programming also without red plug plugged into the module. And checked with tech support using SN to make sure the module was programmed correctly. ?? Thank you.

0

Solid red light after downgrading firmware.

Not able to program evo 1 having solid red light

0

Does the Red led always need to come on 2020 Silverado 1500, Evo-one?

Hello, thanks for looking at my question. I am using an Evo one, with A GM 7 T harness in a 2020 Chevy Silverado 1500 Everything has gone pretty well I installed the T harness, attached both unlock leads to the gray BCM plug, and the tailgate/trunk lead to the pink BCM plug, double checked pins, and that looks good. The Evo1 lights up like it is supposed to, except after the step where I hit the program button 5 times under the yellow LED and turn to run, the RED Solid never comes on the first try. After failing 3 times, I expiremented and turned the key a few tries until it eventually turned red. The steps resumed as expected I got the rapid flashing blue lights at on postion, went inside to windows computer and used the Dcrypter to record the key. that went well, no errors or issues with the fortin software. The problem is that the remote start does not work. Tried both the lockx3 and the lock+tailgate and it does not work to start car. Since the key flashed properly, and the LEDs resumed normally, is that red led lighting after the original 5 program button taps the issue, or are the 7 loose wires needing to be connected to something two greens, one blue, black, orange, orange and black wire. I followed the wiring diagram, these 7 loose wires I find unnerving, was it inferred what to do with these wires as a profession because I am DIY and might need just a little more of an explanation.

1

EVO One module LED stays solid red when trying to program

2015 Toyota RAV4 Evo one regular install. Service number 002B04111969 I am using firmware version 79.65 (Bypass) and 1.[25] (Remote Start) When trying to program the module, I hold the programming button and when I hook the 6 pin connector to it, I get a solid red light and the light below the yellow "loop" is flashing red. I already verified that yellow wire A1 has 0 volts

0

Can'y get blue solid blue led

2006 chevy uplander evo one can't get solid blue led in step 1 programming

0

Can'y get blue solid blue led

2006 chevy uplander evo one can't get solid blue led in step 1 programming

0

Can't get the solid blue light

Hello. I have a 2017 Jeep Patriot, pluged the t-harness to immobilizer, connected the 4-pin connector while holding the program button and all 3 lights keep flashing. How can I get the solid blue to program. Thank you

0

2016Q5 with push start

I got evo-one, when I finally made the setting as recommended by the installation guide: c1, D6 and d2 and 32.6 38.2 now it attempts to start and it unlocks the car but it doesn't starts the remote won't work locking and unlocking doesn't work, the lights (blinkers) flash twice every one minute and the blue light stays on. When I flashed with the latest version 75 something I couldn't get to program on the car the blue light never flash rapidly and it only worked on version 60 any help would be great. Thanks

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue