Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

14/12/2020

 Subaru Viktor Ryzhykh (370Pts.)

0

2018 SUBARU PUSH TO START ATTEMTS TO START BUT NO CRANKING

I have installed and programmed the Evo ONE module on 2018 Subaru Outback Push to Start. The module have been programmed and dycrypted when everything is connected, and 3xlock button is pressed on the remote, the car tries to start 2 times, but there is no cracnking sound on the engine. Please help.

I have also tested the voltage from the root wire and the end(connector), on both sides Immo wire puts out 10.9 Volts.

Another thing I have tried to get the voltage reading oin the Yellow(+Starter) Evo Module wire and it is not giving me any readig (0 V), and the main harness WiteGreen(on the green socket Pin34) isn't giving any voltage reading either, is it supposed to be 12V, when the car attempts to start the wire give 12V. any clues?

P.S. When the car tries to start the starte make clicking noise, but the engine won't crank, so basicaly the starter is in a zooming stage.

Login to reply View 1 answer(s)

08/01/2023

 Mazda moosespectacles (160Pts.)

0

(15 Mazda 3) Car cranks but ignition does not turn on, after steps 1-12

I can get through steps 1-12 (though the security light never displays on the dash), and when the ignition is supposed to turn the car on, the dash lights turn on, I hear a crank, but the car never starts. However, I do get the red and yellow lights flashing, so I tried connecting to the PC to use dcryptor, thinking maybe it will turn on after, but still no luck. Does anyone know what the issue is? I'm using THAR-MAZ1 with the Evo-All and following guide 62681. Everything is plugged in, and the only wiring done is the Lt blue to Lt blue on the 32 pin connector, and the Lt Blue/Black to the red on the 32 pin connector. Am I missing a connection, perhaps an ignition wire? Any help will be greatly appreciated. Thank you in advance.
Login to reply View 0 answer(s)

07/12/2022

 Toyota rashi (130Pts.)

0

Camry not remote starting

remote starting from key or evo start2 doesn't start the car. it does turn on the ignition but not cracking up. lock/unlock, trunk release works from mobile app. 2013 camry push start Evo one with toy6 harness
Login to reply View 0 answer(s)

23/10/2022

 Ford Trevor Voitik2 (130Pts.)

0

Ignition turns on but won’t crank

I just my oem remote and the trucks ignition turns on but it won't start the hood pin is disabled as I don't have one on my truck 2009 f150
Login to reply View 1 answer(s)

20/12/2021

 Volkswagen Steven Cummings (130Pts.)

0

Solid yellow and red light

So im installing the evo all with the tb-vw module in a 2008 vw rabbit. ive been fighting with this thing for a few hours now trying to get the thing to read the key so i can use the dcryptor. ive manage to get past the setup 3 diffrent times but each time i end up with a solid yellow and red light when i apply power back to the evo all. when i go to start it, the yellow will go off then the red starts flashing and wont stop till i unplug it. any advice would be great. also ive tried factory resetting, flashing diffrent firmwares and ive now hit the limit on dcryptor and i believe im one flash away from the limit
Login to reply View 1 answer(s)

03/12/2021

 Volkswagen Kalvin Zimmerman (160Pts.)

0

2016 Tiguan brake and accessories come on but does not turn over, cycles twice.

All lights check out to be correct. Car turns acessories on and applies brake then nothing, then it tries it again and stops for good after that. I have a keywrap right now. Do i the the TB-VW?
Login to reply View 1 answer(s)

15/10/2021

 Nissan joe abboud (140Pts.)

0

Nissan sentra 2013 not starting after 3x lock after programming

I followed guide #33231. Bypass set up was done according to the guide but 3x lock is not starting the vehicle when pressed. The blue led light does flash when lock and unlock is pressed. Is there something that i missed with the remote start options?
Login to reply View 1 answer(s)

08/04/2021

 Honda Annie Williams (130Pts.)

0

Engine doesnt start red light flashes

2014 Honda pilot
Login to reply View 1 answer(s)

03/01/2021

 Ford Vincent Viteritto (130Pts.)

0

2005 ford escape does not crank ?

I installed a EVO ONE with a RF 642w . Everything works locks,unlock,alarm.. When i went to actavate the remote start the parking light comes on as if its going to crank but does not ,parking light flashes 4 times then it try's to start again and fails to crank parking lights flash again 4 times . Then it stops . please help me
Login to reply View 1 answer(s)

12/12/2020

 Subaru Viktor Ryzhykh (370Pts.)

0

2018 Subaru Push to Start attemts to start but no cranking

I have installed and programmed the Evo ONE module on 2018 Subaru Outback Push to Start. The module have been programmed and dycrypted when everything is connected, and 3xlock button is pressed on the remote, the car tries to start 2 times, but there is no cracnking sound on the engine. Please help
Login to reply View 1 answer(s)

12/12/2020

 Subaru Viktor Ryzhykh (370Pts.)

0

2018 Subaru Push to Start attemts to start but no cranking

I have installed and programmed the Evo ONE module on 2018 Subaru Outback Push to Start. The module have been programmed and dycrypted when everything is connected, and 3xlock button is pressed on the remote, the car tries to start 2 times, but there is no cracnking sound on the engine. Please help
Login to reply View 1 answer(s)

16/12/2020

 Toyota Qamar Zaman (130Pts.)

0

Cranked but doesn't start; solid red & yellow light (after it cranked)

Hello, I've installed Evo-One on Toyota Camry 2014 G Key. After successful programming (installation), when I use OEM 3x lock to start the car, it cranked but failed to star; the unit shows solid RED and Yello clor. Any hi9nt pleasee? Thanks, Qamar
Login to reply View 1 answer(s)

30/11/2020

 Ram James granado (190Pts.)

0

2014 ram 3500 push gas push to start pressed 3x turns on no crank

lock and unlock work good
Login to reply View 1 answer(s)

30/11/2020