Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

07/11/2021

 Ford Jesse Slone (130Pts.)

0

2008 Ford Expedition driver door pin wire location?

I am trying to locate the driver door pin wire on the driver's side.  I even cut a wire I was sure was it, only to find that the door chime still went off when I closed the door.  I obviously don't know how to test this correctly 

I tried disconnecting the two harnesses that are in the driver kick panel that are smaller, neither of them seemed to have any effect when disconnected them and closed the door, the chime still stopped.  So it must be in the large connector with the bolt through it, or somewhere else?

In the guide, its says "see diagram", but I can't find one in there to save my life.  I would prefer to stay on the Driver's side since I don't have any wire handy to fish over to the SJB.  Of course, at this point, I would take the SJB diagram, but can't find it.  Thanks for your help!

Login to reply View 1 answer(s)

28/09/2019

 Nissan Mark reite (220Pts.)

0

Door Trigger 2013 Murano not functioning

Eco all in standalone mode. Everything wired correctly. With pink/black hooked up all lights stay on with door closed With wire disconnected remote start works but lights stay on when stopped. If driving vehicle says door open
Login to reply View 1 answer(s)

05/03/2019

 Ford chrisytsma (130Pts.)

0

2010 Ford Escape Hybrid Door Pin Wire Location

I FINALLY found the 26 pin plug where the Green/Violet Driver Door Pin wire is located. It's in the driver kick panel. But it is all but impossible to get to. Really really really difficult as it is buried behind steel braces that cannot be removed. There is certainly not enough slack to get fingers in there to cut the wire and then attach the 2 separate wires needed. How do I accomplish this?
Login to reply View 1 answer(s)

20/12/2018

 Nissan DANG TRUONG (280Pts.)

0

Do I need to Turn On D7 Rap Disable For door pin connection.?? or just leave it off.

Is D7 Rap Disable, Need to trun ON for rap shutdown. on 2014 nissan murano
Login to reply View 1 answer(s)

14/10/2018

 Nissan Marc Fuller (130Pts.)

0

2014 Murano - What is the Door Pin connection for?

I have installed the FORTIN EVO-ALL with THAR-NIS1 in my 2014 Murano. The only connection I was not able to make was the Door Pin connection to the Pin on the BCM connector. I found the BCM, but it's on a board that is too tight to access even after removing the instrucment cluster, etc. Can I leave it disconnected and what will happen as a result?
Login to reply View 1 answer(s)

12/09/2018

 Ford Travis Knick (160Pts.)

0

2013 Ford Focus Driver Door Pin Wire

I need to hook up wires A17 & A18 on a 2013 Ford Focus. I see the location in the WireColor guide. However, the guide shows two Green/Purple wires labeled 117 & 148. How do I determine which one is the correct one?
Login to reply View 1 answer(s)

11/09/2018

 Ford Dan Gagne (360Pts.)

0

Is there any reason I would want to connect Driver Door Pin and Trunk Release in 2013 Mustang OEM 3x Remote Start

My vehicle is a 2013 Mustang with a Manual Transmission.

I have an Evo-One with a THAR-FOR1 T-harness.  I am planning my install and do not understand why the Driver Door Pin & Trunk Release are called out on the Wiring Connection Guide??

I want to retain the factory alarm and OEM remotes' function.

Should I skip these two connections - or, are they important for some reason I do not understand?

Thanks.

Login to reply View 1 answer(s)

23/11/2016

 Nissan Daniel Waslenko (2650Pts.)

0

How to hook up auto light shutdown on 2011 Nissan Pathfinder with Intel key

I am using an EVO-ONE. I hooked the Dark blue from pin A8 to the driver door pin listed on wirecolor as the gray wire at pin 7 on the BCM in the white 15 pin plug. If that wire is hooked up the vehicle starts, then immediately shuts off. I left it disconnected until the customer comes back this Sunday so I can try to figure out what is going on. Remote start operates fine with it disconnected, but the lights do not shut off which will cause battery issues. I do not have the service number on hand. How do I hook up the wire to shut off the autolights? Is it possible that the gray is the wrong wire? Also on the wirecolor site it says the autolight shutdown wire is purple at the parking light harness but it is supposed to be cut. The install guide says to hook it up to the door pin.
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue