Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Stops unless I hit push to start button twice

2019 Dodge Ram Tradesman 1500, new style, 5.7L, auto, Tip start, . Evo One w/THAR6 harness.Using factory lock/unlock/alarm remote, 3X lock to start then unlock to enter the truck.All soldered and heat shrunk connections. Installed back in June, worked great until last week. Starting one week ago, would shut off when I hit the brake even tho I pushed the start button before touching the brake. By accident I found out if I pushed the start button twice before hitting the brake, it would keep running as it had been doing the previous 6 months, what could have changed?...........Mike **EDIT* Now a few weeks later, it won't keep running even when I hit it twice, stops immediately when I hit the brake....any ideas?........Mike

0

Lights stay solid upon intial connection

2017 dodge ram tip key everything is connected correctly but upon initial connection to program when I hold down the program button nothing happens stays solid does not let me select yellow light

0

2016 Dodge Challenger, EVO-ALL w/ CHR6, now throwing U0415 Check Engine Light

As Title indicates, post installation the client is getting a CEL U0415. It happened to me after programming but I cleared it and figured it was a fluke. According to him, per his Dodge dealer, they have seen this happen with aftermarket remotes starts and also stereos on the Challenger. Any suggestions other than rolling back firmware? When tapping for 12V ignition I grabbed the incorrect wire first time around. It was pink/wht but didn't give 12V with IGN. The snake shows Pin 27 OR 31 at BCM, plug E. 27 was the wrong one, 31 was hardly pink/wht, more pink/yel but did give 12V with ignition.

0

Evo all programming 20019 ram 1500 push start

Install complete and verified go to program evo all and at step 5 instead of the blue light coming on the blue and red comes on checked everything twice called tech support and they said don't worry about it. i ignored the red being on and carried on to next step and all was ok. Has anyone else seen this issue i hope they repair this in the guides so installers dont have these issues

0

Why does my remote start occasionally shut the car off after a few secconds?

2015 Chrysler 200. I have the evo chrt6 remote start and occasionally when I activate the remote start the car will start then shut off after a few seconds. It doesn't always do this though.

0

Will any of these products work with OEM remote starter already installed

Hi, I have a 14 Ram 1500, which already has a factory installed remote starter. I'm looking to switch over to Fortin, and use a MyCar RFLink. Can you suggest which product/products i could use to make this work. Thanks! Jesse

0

Evo-all module does not shut off after "push to start button" and shuts off after pressing braker pedal.

I have a 2019 Ram 1500 (newer model, not classic). The OEM remote activates the remote start and is working properly. When I get in the truck and push the "push to start" button once to deactivate the module, nothing happens. When the brake pedal is pushed, it shuts off and I have to restart the truck with the "push to start" button. I have tried programming the module several different ways with no luck. Thanks in advance. Chuck

0

Why do I Get U0001 code. Evo chrt6 on 2018 Ram 1500 gas standard key. Everything works fine.

0

Car doesn’t go into gear unless I press brake and push to start button at same time

My car only goes into gear when I press push to start and brake at the same time. Also it says service fob system. What could be the issue? Chrysler 200s 2015

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2

0

2014 Ram 1500 crimestopper revo 1.1 hangs on yellow when programming remote

installing a revo 1.1 remote starter on my Fortin Evo All unit chrt6 on my 2014 ram 1500. when programming the remote units i unplug the power cable. hold program button and plug power cable back in. i get a solid red and solid blue. i press the program button and hold until the blue and red lights flash out and come back on. I put the key in the ignition and turn to run position i get a solid yellow. red and blue are still lit. when i push the button on the remote unit to pair to module the red and blue light are suppose to blink to acknowledge the remote unit has been programmed. on my unit the red and blue light go out and only the yellow light remains on. firmware 74.37. In my flash link setting under data protocols everything is greyed out i cannot select F2

1

2017 Ram 1500 Tip Start, Will Not Remote Start

Details: 2017 Ram, Gas, Tip Start, CHRT6, OEM Remote Flashed with standalone, T-harness, with built in alarm, 74.[37] firmware, 6.0 hardware. No hood pin, valet switch, or parking lights connected. C1 and D1 enabled, #8 blue wire does not turn red when grounded. Everything seems to be installed correctly. The key programs without issues. Flashes without issues. The blue light falshes each time the lock button is pushed. The yellow light comes on when it is started with the key. Problem: When I attempt to remote start (3x lock button on the EOM remote) nothing happens on the unit or in the truck. No attempt to start, no dash lights, nothing. Any advice?

0

Programmig not working stuck at step 9

i have double and triple checked my wire connections but when i try to program my THAR-CHR6 and when i get to step 9 the light will not change from Red to blue. I have attempted this multiple times and have followed all the steps so i am lost and really could use some help. Could it be an issue with my unit or is there a trick to this i am missing. I am installing on a 2013 Dodge Journey Push button ignition. *Update* I had intially started i had updated my Evo to the most recent firmware not in beta. I downgraded to 74.22 and was able to get to the next step where the blue light would come on but it would not flash. Flashed it again to a higher FW believe 74.25 but same thing blue light doesn't flash. Otherthing i noticed is on the ODBII port guide says the CAN high wire is brown but there are no brown wires on that harness. The CAN low matches the yellow though.

0

Programmig not working stuck at step 9

i have double and triple checked my wire connections but when i try to program my THAR-CHR6 and when i get to step 9 the light will not change from Red to blue. I have attempted this multiple times and have followed all the steps so i am lost and really could use some help. Could it be an issue with my unit or is there a trick to this i am missing. I am installing on a 2013 Dodge Journey Push button ignition. *Update* I had intially started i had updated my Evo to the most recent firmware not in beta. I downgraded to 74.22 and was able to get to the next step where the blue light would come on but it would not flash. Flashed it again to a higher FW believe 74.25 but same thing blue light doesn't flash. Otherthing i noticed is on the ODBII port guide says the CAN high wire is brown but there are no brown wires on that harness. The CAN low matches the yellow though.

0

2017 dodge ram 1500 tip key, will the evochrt6 work and is the flash loader needed also?

0

2016 challenger check engine light on after 3x remote start

I have evo chart6 installed into my 2016 challenger and now only on remote start 3x lock, i get a check engine light, no code comes up when checked? I can start car with push button and the check engine light is not on. What is the fix? I read on another dodge check engine light problem it was noted to flash with 74.18 Will this fix the problem? I have flashed unit to 74.18 but I still need to know an answer as my son will put the unit in his car and I will need to know before I give it to him. thanks Steve

0

MUX relay required on challenger?

Two issues, maybe related to the same answer. Installed EVO-with CHRT-6 in standalone mode, honk 3x's. When using the remote start it triggers a check engine light, pulling the code indicates the Brake Module is detecting a signal when it should not., 0415 antilock brake invalid signal I am assuming this has to do with the MUX wire. Does the push to start challenger 2016 up require a mux relay? Can I follow the same wiring as mentioned in another thread? Next, just to confirm vehicle take over. When using remote start about 15 minutes after driving, the car rolls the drivers window down partially, turns on the interior lights and dispalys a door open chime and popup on screen. It is very consistant at 15 minutes which i know is the run time for my module. I am wondering if what I am doing is wrong for vehicle take over, or if the mux/check engine light are related to this issue. Currently, honk three times, car starts, after running a bit I enter the vehicle, note has touch sense doors to unlock, i put my foot on the brake, put in drive and go. Fifteen minutes later the car does above as discribed.

0

I cant get through the programming on evo chrt6 2016 challenger

2016 challenger push to start , I installed the evo chrt6 and got to step 6 the red light on and it would not do anything else I unplugged and started over and the yellow light would not flash after the 4 x button I did a unit reset, I hope i didnt mess up anything in the settings by doing this now it is stuck with the yellow light and it wont do anything Can you check my programming to see if it's good? i am using factory remotes for 3x start what do I need to do? please help

0

Which installation procedure to use, and why?

When installing EVO-CHRT6 in 2017 Dodge Journey with Push to start should installer use "Regular Installation" (12131) or "Standalone Installation" (12211). I believe this application will use regular as the EVO will be used by itself without another aftermarket starter.

0

16 Ram 1500 wont recognize the ignition wire

I have tested the ignition wire and i get a solid 12v but the module stays blur after programming. Can you list every mandatory connection? Running oit of ideas and have cleared and flashed and re updated the module with every update thats on there. Did test where you hold the button until it turns blue and tge module remains blue when vehicle is off and on the ignition/run. Bad module? Vehicle is standard key/tip

0

Programming second key

1st key works no problem but the second key remote starts but it wont let me unlock or lock the doors to get in my truck do i program the second key just like the 1st key

1

2016 - DODGE JOURNEY - SE - 4 Buttons FOB Original DODGE - Programming the starting BUTTON

I have an original Dodge 4 buttons remote with the starter button option, can I program that button to work with my CHRT6?

2

2016 Dodge Journey - SE - Push Button ready - Ignition Cable Not Found

The ignition wire in according with the instructions is Pink/white, but it's not. It doesn't generate 9V when car starts. Which cable color should I use?

1

Wont start using 3x lock 2016 Dart

EVO-CHRT6 I have a 2016 Dodge Dart. I got it programmed according to the instructions. Dycripted it and programed the module and it says all good. I plugged it back into the vehicle. When I push the lock button on factory remote 3 x the blue light flashes each time but nothing else happens. No other lights or anything.

0

2013 Dodge Ram 2500 Won't Lock After Start Up

Installed Evo-All with T-Harness 6. Connected RF Kit. Flashed to latest firmware.(74.30) Push lock 3x and doors unlock but will not lock once running (but the tailgate locks). If truck shuts down then they will. All functions work with rf kit and oem key, just wont lock doors after start up. Evo is programmed to unlock and lock for oem alarm disarm.

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer