Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

KHY3 t-harness procedure connection

what meen in procedure manuel t-harness the ignition output for convinient device? need to conect purple/yellow wire? thanks

0

Wire connection connections to controll oem remote after start Evo-all with GMT1.v2 T-harness

I have a chevrolet sonic/aveo 2012 and have now the evo all with GMT1.v2 installed and also already make the connection to the obd port1 and make the connection to my lightswitch. But my oem remote is not functional after i remote started. But there must be an modificiation to shut down also with the oem remote. Somebody can help me?

0

EVO-START2 - is the ignition wire not needed in some cases?

I setup an EVO-START2 with an iDataStart HCX in a 2016 Kia Sorento (push-start) but since there's a T-harness the only manual connection required for the entire install is from the EVO-START2 (yellow igition wire). The T-Harness doesn't connect to an igition wire in the vehicle, so I can't just run the EVO-START2 yellow ignition wire to the HCX or T-harness. Instead I have to connect the yellow ignition wire to a longer wire that can reach the driver kick panel, and tap a connector there. I tried setting up the EVO-START2 without the yellow ignition wire and could not get validation (purple LED flashing) to happen, which didn't surprise me too much. I temporarily connected the yellow igition wire by pushing it into the back of the relevant pin/connector in the driver kick panel. This got me past validation and everything worked. To finish the install I needed a longer wire, so I left the vehicle to find a wire and to show my wife the app. We started and stopped the vehicle, locked/unlocked doors, etc. It all worked (we could hear the vehicle from within the house and the app confirmed every command). To my surprise, when I got back to the vehicle, the yellow wire had fallen out of the connector it was temporarily pushed into. This caused me to wonder if it was disconnected the whole time I was away, and so I tested functionality without it. Everything seems to work without that wire (except for the one-time validation step). As a secondary test I tried starting the vehicle using OEM fob and watching to see if the app reported that the vehicle was on. It did and showed the countdown timer and temperature etc. I can't find anything not working. So this leads me to the question in the title - do I actually need this wire? Everything presumably is working through data without it. If I don't connect it then I have a 100% plug-and-play installation, which is ideal.

0

Ignition not wired according to Tharness wiring but shown wired in regular installation wiring

Guide #71221 for my prius shows a yellow wire going to connector A pin A1 on the Evo One. I traced the wiring on my t-harness and it only goes to the 7 pin steering lock connector which isn't connected and spliced on the wire that shows it should be isolated. But on Guide #59741, it shows a wire from to a connector on the fuse box. I'm unsure why it's needed there, but not needed when using the T-harness? This is for a 2018 Prius hybrid using an EVO One

0

2 start and 2 ignition wires

2004 Toyota Camry EVO-ONE istall. This car has 2 ignition (black/red,black/yellow) and 2 starter wires (black/white,black/yellow). When I connect the 6 pin plug, which ones on the car am I supposed to use?

    

Thanks again for making such a good product!

 

0

2017 Jeep Cherokee ignition wire, No temp sensor

I see on your site where to find a 2016 ignition source but cannot find a wire on the 2017. Do you have any wiring diagrams or pics on where I can find a wire?

0

Ignition wire hook up jeep cherokee

2016 Jeep Cherokee. Evo all chrt6, is there a wire on the chrt6 tharness I can hook up the yellow ignition wire to since my truck dorsnt have a temperature sensor in dash?

1

fillage ignition fils vert sur certaine image

 

first guides #29021 we have red 12v power and green is +ignition...... second....on picture from wirecolor red +12v  50  is the same on the guide but wire green 53 on the picture is different in the guide 29021... why ignition wire is different.......also in the guide 29021 if you zoom the picture you see red number like 50 end 53....   my car is genesis coupe 2014 automatic 6 cyl...

 

2

2016 Dodge Journey - SE - Push Button ready - Ignition Cable Not Found

The ignition wire in according with the instructions is Pink/white, but it's not. It doesn't generate 9V when car starts. Which cable color should I use?

0

2014 Grand CHEROKEEKEY STAND ALONE IGNITION WIRE

 

2014 grand CHEROKEE KEY STAND ALONE IGNITION WIRE wher can found it bec there is no 10 pin Near the driver side 

1

2007 Lexus GS350 (+)Ignition Wire

Trying to install Evo-One. Instructions only say connect to ignition(+) at fuse box. WireColor chart only shows (-) Blue wire at fuse box. Is this just a mistake? Other manaufactures show a ignition(+) at the brake switch, but also say this requires a diode to be put in place. Instructions show the connector for the start button, but not which one to use at the fuse box. Fuse box has multible blue wires. Also not real sure about the location of the Blue wire in the Parking Light Harness. S/N 002B07 147486

0

Power source other than ignition wire connection

Can the unit get power (yellow wire to ignition) from the obd2 connector constant 12v instead of the ignition wire on the evo all?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer