English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

13/12/2020

 Ford Brandon Cleary2 (130Pts.)

0

2020 Ford F350 key takeover and trans "bump"

Customer just called me and stated that after remote starting his truck if he presses the brake it won't shut the vehicle off. If he puts the key in the ignition and then presses the brake, takes the key out, the truck will shut off. When I did the install using an evo-fort3, pressing the brake did shut the truck off with the key not in the ignition. He also states that when the remote start starts his vehicle it feels like the transmission engages for a split second. It is and automatic. He says it feels like someone steps on the rear bumper.
Connectez-vous pour répondre Voir 1 réponse(s)

24/10/2020

 Ford Joe Callaco (380Pts.)

1

2018 F-550 no HVAC

Hello, I Installed FORT3 EVO-ALL on a 2018 F-550. I thought it was all good, but noticed the other day that the HVAC controls do not work while running remotely. The only connection I made was behind the OBD2 port, by far the easiest/fastest remote start install ever! Am I missing something on the programing of the EVO-ALL, or do I need to make another connection for HVAC to work properly. Thank you, Joe
Connectez-vous pour répondre Voir 1 réponse(s)

09/10/2020

 Ford Jaeden Hudson (340Pts.)

0

What is the actual run time of the FORT3 kit

2017 F150. I do not have the options enabled in the dash for remote start. I do know that if the options are not enabled in the dash technically the trucks BCM will still run the truck for the default time of 10 minutes. I set the Evo All to run for 20 minutes. Will it actually run for 20 minutes or will it still be the default 10 minutes the truck has?
Connectez-vous pour répondre Voir 1 réponse(s)

26/11/2019

 Ford Thinus Du Plessis (160Pts.)

0

Idle time on Fort3

How can I extend the idle time of my truck wile running on remote start, current time seems to be 3min and that is way to short, I need it to be on min 10min to 15min for the truck to warm up properly where I live. This is on a Ford F-150 2019 model and the Module is Evo -all Fort3
Connectez-vous pour répondre Voir 1 réponse(s)

23/11/2019

 Ford Thinus Du Plessis (160Pts.)

0

F-150 2019 std key and without keyless entry- Correct Installation guide

When I use the dropdown selection tabs on top to get the correct installation guide there is multiple options with no discription of the 2019 model. I need to know which installation guide to use for a 2019 F-150 std key and without keyless entry, truck. The product that was shipped to me is the EVO-Fort3 package
Connectez-vous pour répondre Voir 1 réponse(s)

11/11/2019

 Ford sdgfsdf sdfsdfsd (160Pts.)

0

2018 Ford F-150 STD key evoall not starting truck

Plugged in the Tharness correctly. When connecting the moduel I held down the small button on it while connecting the black power wire, and let go of it when the light was blue. Connected the white wire on the other side of the module. turned on truck to ignition on, waited for blue light to flicker for a bit then ignition off and key out. Tried the triple press on lock and nothing happens. Turn to ignition on again and the module is showing a yellow light.

Cant get the remote start to work

 

SN:001A07005461 Model:EVO-ALL

 

Connectez-vous pour répondre Voir 1 réponse(s)

01/11/2019

 Ford sdgfsdf sdfsdfsd (160Pts.)

0

2018 Ford F150 Std Key Fort3 isnt remote starting car

Plugged in the Tharness correctly. When connecting the moduel I held down the small button on it while connecting the black power wire, and let go of it when the light was blue. Connected the white wire on the other side of the module. turned on truck to ignition on, waited for blue light to flicker for a bit then ignition off and key out. Tried the triple press on lock and nothing happens. Turn to ignition on again and the module is showing a yellow light. Cant get the remote start to work
Connectez-vous pour répondre Voir 1 réponse(s)

09/08/2019

 Ford julio pelayo (1650Pts.)

0

Does data cable have enough power to power remote start alarm?

Installing thar fort3 with compustar cm7000 remote start and alarm using guide 68941guide shows remote start being powered by datalink, does datalink cable have enough power to power the remote start and alarm? The siren, shock sensor, led? Cm7000 comes with a low current harness with a 3 amp fuse but guide shows it's not needed if using datalink. Also there is no fuse used in guide is it safe to install without a fuse? Also should unlock before start be turned on? 2015 ford f150
Connectez-vous pour répondre Voir 1 réponse(s)

30/07/2019

 Ford julio pelayo (1650Pts.)

0

Hi, thar fort3 and compustar remote start/alarm 2015 ford f150 install

I'm installing thar fort3 with compustar remote start alarm on 2015 ford f150.what will turn on the truck? The evo all or the compustar? What options do i set? C1 only? Do i set run time on evo all or compustar? Is run time limit 15 minutes or can i set longer run time on compustar? Do i use guide 68991 or 68941
Connectez-vous pour répondre Voir 1 réponse(s)

08/07/2019

 Ford Robert Smith (130Pts.)

0

2016 F150 XLT Std Key EVO-ALL w/ Fort3 Standalone Mode C1 & D1 Options Good--No Start

I am in the process of installing an EVO-ALL device with a Fort3 cable into a 2016 F150 XLT with standard key.

    The module programmed correctly. The hood is definitely closed. When attempting to remote start using a LOCK, UNLOCK, LOCK sequence the BLUE LED flashes once with each LOCK button press and twice with the UNLOCK button press. After the third (LOCK) button press the LEDs go through a flashing sequence that ends with a pause (no LEDs lit) followed by three quick flashes of the RED LED which I understand means NO TACH.


I verified that options C1 and D1 have been turned ON by doing the following:

    I grounded the A8 pin of the 20 pin connector.  The RED LED did NOT light so option D1 should be on. I momentarily grounded the A13 pin of the 20 pin connector.  The LEDs went through a flashing sequence very similar if not identical to the one that they go through when attempting a LOCK, UNLOCK, LOCK type remote start.  The flashing sequence ended with the same pause (no LEDs lit) followed by three flashes of the RED LED which I understand means NO TACH.

 

Any ideas?

Thanks!

Connectez-vous pour répondre Voir 1 réponse(s)

07/01/2019

 Ford Kevin Melone (410Pts.)

0

2018 Push To Start Ford Fort3 Evo-All

Hello, I have the preprogrammed T-Harness clipped in properly with the black 4-pin cable and white cable in the Fortin programmer. I have waited till the light turns blue to plug the TWO connections in. Once I turn on the push to start ignition, the light goes off. If I press the button it will begin flashing over and over again. After this if I turn the ignition off, the light stays blue. If I click my remote (I have updated the programmer and clicked LOCK UNLOCK LOCK), it flashes red, then both red and orange, clicks once and shuts off. It never hits all three colors to turn the ignition on.
Connectez-vous pour répondre Voir 1 réponse(s)

07/01/2019

 Ford Kevin Melone (410Pts.)

0

How do I install EVO-ALL FORT3 on 2018 Mustang?

Hello, I am really having some trouble with this product. So I ordered the preprogrammed plug and play Evo-Fort3 with T-Harness, with the StandAlone I believe. I have updated the programmer with the flashlink system but my main question is, can I just simply install it into the car once updated with JUST the T-Harness and connected wires? Or do I actually have to cut and sauter all the other wires included in the package? Including the hood pin and switch? I was under the impression off your website when looking into this that I could just install it immediately with what was given instead of having to turn into a car genius and cutting all these wires. Please help me out here man. Thanks. I have installed it multiple times through the back of the OBD11 port just as the unit comes as a whole and got through some programming until I go to try the remote start, then it flashes red then both red and orange and clicks but car does not start.
Connectez-vous pour répondre Voir 1 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer