Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2015 f150 push button : eco-fort3 no power after months of use

I have it hooked up to a LinkR-lt2. Worked fine for months and suddenly stopped working. Evo all module not getting any power

0

Hi, thar fort3 and compustar remote start/alarm 2015 ford f150 install

I'm installing thar fort3 with compustar remote start alarm on 2015 ford f150.what will turn on the truck? The evo all or the compustar? What options do i set? C1 only? Do i set run time on evo all or compustar? Is run time limit 15 minutes or can i set longer run time on compustar? Do i use guide 68991 or 68941

0

2016 F150 XLT Std Key EVO-ALL w/ Fort3 Standalone Mode C1 & D1 Options Good--No Start

I am in the process of installing an EVO-ALL device with a Fort3 cable into a 2016 F150 XLT with standard key.

    The module programmed correctly. The hood is definitely closed. When attempting to remote start using a LOCK, UNLOCK, LOCK sequence the BLUE LED flashes once with each LOCK button press and twice with the UNLOCK button press. After the third (LOCK) button press the LEDs go through a flashing sequence that ends with a pause (no LEDs lit) followed by three quick flashes of the RED LED which I understand means NO TACH.


I verified that options C1 and D1 have been turned ON by doing the following:

    I grounded the A8 pin of the 20 pin connector.  The RED LED did NOT light so option D1 should be on. I momentarily grounded the A13 pin of the 20 pin connector.  The LEDs went through a flashing sequence very similar if not identical to the one that they go through when attempting a LOCK, UNLOCK, LOCK type remote start.  The flashing sequence ended with the same pause (no LEDs lit) followed by three flashes of the RED LED which I understand means NO TACH.

 

Any ideas?

Thanks!

0

2016 Ford F150 doesn't display run time after vehicle starts.

A network error comes in after a minute or so, but the vehicle is running ?

0

2016 Ford F150 doesn't display run time after vehicle starts.

A network error comes in after a minute or so, but the vehicle is running ?

1

2016 Ford F150 Standard key Evo-All w/T-harness fort2

Won't program. All connections verified 5 times good. gets to the point of inserting 2nd key and removing it, ignition turns on red and yellow light on won't program can bus no blue light flash. Blue light at one time flashed after that but ignition didn't turn off and yellow and red light didn't alt flash. Should it take long between lights flashing? Very frustrated!!!!

1

2016 Ford Transit Evo One T Harness issue

I think there may be a larger problem here that requires a rewrite of instructions. My 2016 transit also only has the bottom 7 pin connector and no 4 pin connector on the ignition barrel.


I used the T harness but I had to refer to the regular instructions, the T harness instructions and the Wirecolor.com photos and instructions to put this all together.

1. Both the regular and T harness instructions label the 4 pin connector #1 in some places and #2 in others. Same with the 7 pin connector.

2. In the regular instructions, the seven pin connector has the pin numbers labelled incorrectly. Pin 5 is actually 4, 6 is 5 and so on.

3. On the WireColor instructions, wires 6 (RX) and 7 (TX) are listed as being from the 4 pin connector, but no photos are referred to or included in the WireColor package. This leads me to believe that the 4 pin connector photo was not included since it does not exist.

4. This is where it gets confusing. On the regular installation instructions, pin 5 on the 7 pin connector (which is actually pin 4) connects to D5 (+ 12 Volt) which is fine. However, pin 6 (which is actually pin 5) is highlighted but not assigned. The WireColor instruction sheet lists this as Wire 70 (+ key sense). I am guessing that the pin should be assigned and here is why. While in the van with the door shut and quiet, when I place the key into the ignition I hear a sound come from the ignition barrel like a small motor or a relay without turning the key. That tells me that the vehicle is recognizing the key. Since there is no wiring diagram included with the T harness, I can only assume that I will have to make another connection to ACTUAL pin 5 on the 7 pin connector.

5. The regular instructions show wire D6 Ignition1/Accessory making two diode protected connections to the 7 pin ignition connector. The T harness does not appear to have any built in diode protected connections. Is this an oversite or on purpose?? Again I have no problem adding diodes to my T harness. EDIT: Upon further examination,  it appears the T harness uses different connections to accomplish the same thing.
 

As it stands now, I have done all wiring according to the current instructions and connected the Evo One but have not programed it. I did follow the above "release on blue" instructions instead of the instruction sheet "release on red", but the flashlink manager did not regognize the EvoOne after that. Leaving the installation as is for the time being seems to be fine, So I will leave it in place for now even if it is not working yet.

I hope you can resolve this quickly and it will be helpful to others. I installed the EvoOne unit on my other vehicle a year ago and it works great.

 

2

2016 ford transit 250 t harness not available yet for the evo all?

Was told by one of distribution dealers (Clutchfield) that the t harness-with plugs for the evo all is not available yet for the 2016 ford transit, needs to be all spliced in,if so when will it be?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer