Questions & Réponses

 have the OEM remote control then I have the EVO-ONE SN: 002B07 239663, THAR-ONE-MAZ3.

CAN YOU RESET  : EVO-ONE SN: 002B07 239663 

Please help and thank you.

I have installed the EVO-ONE-942 with THAR-ONE-MAZ3 on my 2016 Mazda CX5 Automatic Push Start, and when scanning the vehicle with Thinkcar I get a DTC in EPS module, code U0338:00-08 (Software incompatibility with remote function actuation).

After clearing all code, it comes back again ...

Also, I've noticed the trunk open on the remote opens it half way, meaning it still cannot be actually opened until you unlock the car. Is there a way to disable trunk open as it doesn't work right?

Another weirs "issue" I found, when the car is unlocked with Fortin remote, then locked with "OEM" remote, when you check status with Fortin remote, it will say unlocked even though it's locked. Then when you lock with Fortin remote, it will report the status correctly.

The module seems to work fine, I have completed every step in the installation guide. However, the start button does continuously blink amber/orange while the vehicle is running and does not stop until the engine is shut down. This only happens when started normally, not remotely. If I disconnect power to the EVO ONE, the car can be started just fine and there is no blinking light. I used the THAR MAZ 3 t-harness to install. I have been scouring the Mazda forums and have found no answer. Everyone says either replace the fob batteries (I replaced them) or visit the dealer. The mazda dealer wanted $150 to diagnose the problem, and then doesn't want to even look at it after learning the Fortin system was installed. 

It's like a false/positive situation. I had someone overpress my rf remote and oem key was starting car on one lock. blah blah blah

Reprogrammed both sets of keys (2 oem's and 2 RF RM411 long range one way remotes). Everything works fine again, but if I use the one button RF RM411 I get the code thrown and a little red security light stays on for a couple of seconds once my key is in on position in ignition.

Now if I just use the OEM key, I don't get the red light. Also there is no engine light with code. The only reason I know it's there is I had the car seafoamed (should have done through break booster after MAF, used intake manifold. Had engine lights galore and ended up changing all 16 spark plugs myself (the good ones) and clearing misfire and crankshaft sensor codes.

Anyways, all is working great now, except this code I can't seem to clear in any way. Is this an issue with my car or Chrysler products? 

Usually when you have this code, the car will start but quit soon after.

Just let me know and I will just leave it alone and not worry about it.

Just reinstalled a new remote starter for my friend using evo-all bypass module.

The car is Nissan 2011 Quest PTS. I got the message said "Dcryptor's Limit has been reached for this car." when I went to the dcryptor step.  Then the installation was interrupted. This case is my second case. The first one I had to buy a new one to replace it. 

Can anyone give me some help?

SN:001A06 854069

Log into use GingerLimited modethe descriptor step×

Just reinstalled a new remote starter for my friend using evo-all bypass module.

The car is Nissan 2011 Quest PTS. I got the message said "Dcryptor's Limit has been reached for this car." when I went to the dcryptor step.  Then the installation was interrupted. This case is my second case. The first one I had to buy a new one to replace it. 

Can anyone give me some help?

SN:001A06 854069

Log into use GingerLimited modethe descriptor step×

I just bought an evo-all with a GMt1 T-Harness. Upon connecting it to my computer, I get an error saying flash limit reached 0/0.  The Service Number is 001A06 242453. Can this be reset?