Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

Sequence

Bonjour, J'ai un démarreur model FTX 94 installé sur une Nissan Sentra 2021 manuelle avec bouton poussoir. Lorsque je descends temporairement du véhicule (par exemple pour la poste) si j'applique le frein à main, le moteur s'arrête automatiquement lorsque j'engage la première vitesse lorsque je veux repartir. Si je n'engage pas le frein à main, aucun problème. Quelle est la séquence que je dois faire pour pouvoir redémarrer sans que le moteur ne s'arrête lorsque je quitte temporairement le véhicule de façon sécuritaire (avec frein à main) ? Merci à l'avance et Bonne fin de journée

0

2014 Audi Q7 Starting Sequence using

HI there,

I've recently purchased a 2014 Audi Q7 that came with the Fortin remote starter, I believe its a legacy version that you used to sell. Board Front: FAR 2006 XH29926. Is it possible to find a manual for this? I'm having a hard time figuring out what the remote starting sequence is?

0

Fortin Evo All connect with Car alarm system with push button

Hello, I have Chevrolet Cruze 2012 with original key and Evo All connected with t-harness GM1v2.

I wanna to install car alarm system with push button and PKE. 

I dont wanna use original key at all, fortin should work like immo bypass. 

What I want: open car with key from alarm system, start the vehicle pushing the start/stop button and car shouldn`t stall when I push a break pedal.

How can I do that?

Sould I connect:

1) 2. IGN1 wire to yellow fortin Ign wire

2) 4. ACC wire to brown fortin wire (pic. 2)

3) Or need to use some of the fortin wires: A13, A16, A18? 

4) A8 GWR needed?

5) Reprogramming Fortin nedded? 

 

https://www.dropbox.com/s/hwnyxc2s7p25f94/connection.png?dl=0

https://www.dropbox.com/s/m4slmfpwlo4japt/Fortin%20regular%20installation%20t-harness_page_4.jpg?dl=0

 

0

Evo-one ....Fail from step 1.....

Evo-ONE + T-har FORT1

I was holding the programming button while connecting the black 4pin to start programming the module.

But, as the manual says, the LED didn't stop and just kept lit in the red-yellow-blue sequence.

It doesn't work from step 1... There are also videos... What was the problem?...

0

Evo-one ....Fail from step 1.....

Evo-ONE + T-har FORT1

I was holding the programming button while connecting the black 4pin to start programming the module.

But, as the manual says, the LED didn't stop and just kept lit in the red-yellow-blue sequence.

It doesn't work from step 1... There are also videos... What was the problem?...

0

Blinking amber light on start button 2016 CX-5

The module seems to work fine, I have completed every step in the installation guide. However, the start button does continuously blink amber/orange while the vehicle is running and does not stop until the engine is shut down. This only happens when started normally, not remotely. If I disconnect power to the EVO ONE, the car can be started just fine and there is no blinking light. I used the THAR MAZ 3 t-harness to install. I have been scouring the Mazda forums and have found no answer. Everyone says either replace the fob batteries (I replaced them) or visit the dealer. The mazda dealer wanted $150 to diagnose the problem, and then doesn't want to even look at it after learning the Fortin system was installed. 

0

After market push button install

Hi,

I am planning to install Smart Entry and Push start system from Advancedkeys.com for 2013 Toyota Camry

I currently installed Fortin Evo one in this car.

Smart entry, push start system from advancedkeys.com states that they support Fortin for immbolizr bypass.

Please refer https://advancedkeys.com/Prod_AK105B.html in that scroll to bottom of the page and look for bypass device enable output..

Question. 

1) After market push start system (AK105B) can output negative ground out while running, can I can take this ground out from this module and activate my fortin evo one for immobilizer bypass.

2) Just incase if you want to know the Manual of after market push start system. Please refer to https://advancedkeys.com/Prod_AK105B.html and in that look for details/manuals section click that tab and scroww down to download AK-105 Smart Key Installation Guide

3) Do you guys plan to sell something similar in future or is this in your pipeline.

4) Please note this unit is capable of doing remote start but i am planning to use fortin evo one for remote start and strictly using other one for push to strat and smart entry.

 

Thanks in advance.

0

VALET BUTTON SWITCH

i was buy reciently 2 new evo one units , and this time both order recieve without valet button switch , i has been bought in past unites and it was inclueded , is there change in inclueded items from the old units "EVO ONE", and how i can get valet switch button !

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer