Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2009 forester manual transmission

Instructions for the Evonne don't call for it but why is the emergency brake, brake pedal not wired as well. And what happens if the car is left in gear?

0

Can i get a key reset my vehicle lemit has been exceeded

0

Can i get by evo bypass key reset resched my vehicles lemit

0

I want rest limit sn; 002B04 676425

0

2017 Ram 1500 Start briefly then shut off

Installed the fortin evo all with THAR-CHR7 and a 5706v w2w. Programmed according to instructions. Everything is working properly except I can't get the vehicle to remote start every single time. It starts and shuts off right after starting. Sometimes the truck will remote start and stay running like it should but not everytime. What could be wrong? Is it the firmware version?

0

Dcryptor reset

EVO one sn 002B04 651595 dcryptor limit reached needs to have limit reset.

0

SN: 002B04 671964 PLEASE RESET DEVICE

Dcryptor limit has been reached EVO-ONE SN:002B04 671964. When connecting via Flash Link 4, there is a failure and then it reconnects again.

0

2012 Civic starts then stops three times

Hello, I have had a remote start on my 2012 Honda Civic for 5+ years. It has quit working. It is a EVO-ALL and CrimeStopper RS00-G5. From following the troubleshooting I think it has to do with the tach signal but not sure what to check. The car will start for about 3 seconds then shut off. It does this three times and then nothing. While it is running the starter is engaged the entire time.

0

2013 CX-5 Cranks But Won't Start M/T

EVO-ONE. I have the THAR-ONE-MAZ3 harness. White cable for clutch bypass is connected. Not sure what's going on. I've tried changing the programmable output from 2.1 (default) to 2.2 (I think it should be this one?) and still no luck. It will try to crank for a few seconds, then shut off then tries again for a few seconds but won't start. Yellow jumper was cut when I received it, but it is currently twisted together until I verify what the issue is then I'll do a more rigid connection. I don't have the hood pin switch connected, my kit didn't come with it. Not sure if this is preventing it from starting or not. I have tried enabling and disabling A11 for this but still no luck with remote start. SN: 002B04 643579

03/12/2024

Toyota G M (15170Pts.)

0

2024 Prado

Hello. I installed evo-one (002B04683100) on 2024 Prado. Programming and decryptor were successful, but when I connect the 6-pin connector, all the LEDs blink

0

I want firmware vision 0.80 for remote starter and I want rest limit sn; 002B04 676425

I want firmware vision 0.80 for remote starter and I want rest limit sn; 002B04 676425 For Mazda 6 2016 and how can I make doors close when I put driver mode and when I put parking mode doors open

0

where I can find an older version of FlashLink Updater / Manager ? v3 or v2

where I can find an older version of FlashLink Updater / Manager ? v3 or v2? Please advise Thanks

0

solid orange and red light after 1st decryptor

Trying to get my remote start in my 12 Passat TDI working. When I get to the decryptor stage 2 it just has solid orange and red light on when you reinstall and turn on the key, it stops there, just those 2 lights.

its t harness VW_T6 so there isn't really much to hook up, all plug an play except i had to wire in the key reader.  car doesn't need the brake pressed, and i didn't wire in the hazzard wire as it was listed as optional.  seams like it read the key fine, and the app seemed to program the unit after. 

any ideas what i can try, i have all ready hit the flash/decryptor limit. the last thing i was trying was to use the firmware in the instructions instead of the recommended in the app. however i could not do the decryptor step as i hit the limit. 

03/12/2024