Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Eric Laing

Joined on the:

Nov. 23, 2018

Score

390

Comment(s)

13

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

3

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

0

2016 Juke parking light wire resets car features

I have 2 2016 Nissan Jukes, yes, his and hers. My starter works fine and turns on the parking lights (brown wire to purple wire of green pin1 at BCM connector), when I put the brown to purple in my wifes car, the lights don't turn on and it resets the radio/time to factory, every time. Again, identical 2016 Jukes. I am NOT pulling the starter out of her car as where I have it tucked in takes a long time to get at. Verified 12v at purple wire with manually turning on the parking lights but when remote started the Fortin brown wire has nothing. Ideas?

0

Ground pulse after start to trigger defroster

My car (2016 Juke) is a negative 'pulse' to trigger the rear defroster. I keep reading about using the Aux1 to trigger, I don't have an Aux1 that I know of and if I do it's not listed in the install guide. Basically, AFTER the car starts I just need to pulse the pin at the BCM to ground to get the defroster going. Any help is appreciated. Don't have my service model # stuff with me and I'm not taking the unit out of the car just to find it. It's an EVO-ONE NIST1 with the T-harness.

-1

Juke still runs after brake press even without key

1: Everything works fine, but I think I found a glitch. If I remote start my 2016 Juke and leave the key inside after unlocking the doors, pressing the brake flashes the parking lights like it should but it still leaves the car running... WITHOUT THE KEY IN THE VEHICLE!!! 2: If I then try to shut it off by going back in the house and lock-lock-lock it does nothing as it has been placed in 'take over mode' or whatever it's called. I have to physically push the start/stop button to shut it off. THEN it starts back up because I recently pressed lock-lock-lock. First issue scares me the most.

0

Remote push start evo all for Nissan GTR, all programmed correctly but won’t start. Break lights shows but no start?

Installed the Evo All in a 2012 Nissan GTR, everything pulgged up correctly on the instructions. Programmed key fob as it shown, went smoothly with every step. Once finished and time to start the car with the oem key fob with the 3x lock button it will not start but only the break light works? How come it did not start up?

-1

It's official, EVO-ALL NIST1 is useless

I've tried everything. Resets/reprogramming, wires connected/not connected... when it's all said and done I have a t-harness that seems to work, brake lights come on - dash shows the 'push brake' icon and it never starts. Nothing. Lights flash 3 times and it's done. 2016 Juke AWD CVT. What a waste of my time and money.

-1

evo one remote start works, but no accessory power until i get in and turn the key

well basically.... the title. 2004 350z, i have option 2.3 enabled like it says in the guide, not sure where i'm going wrong

0

EVO-ALL NIST1 no start, press brake light on.

I've done SOOOOOOOOO much searching and nothing has helped. 2016 Juke PTS T-harness, everything connected properly (verified voltage and connected PTS wire (black/white A19)). Brake lights come on after my programmed lock-lock-lock, Fortin clicks a few times (relays inside) but car won't start then the red LED blinks 3 times and that's it. The entire time the amber dash 'press brake' icon is displayed. Thinking I have now wasted my money buying this starter that after about a month of trying to install still does not work.

0

Nissan Altima to start using EVO-NIST1 only when brake is pushed

The remote start works great with key fob out of vehicle, the only problem is that I need to manually press the brake for it to start. Is the EVO-ALL suppose to send something to simulate that the brake is pressed?

-1

NIST1 yellow led won't blink to program

Tried installing my NIST1 today and a couple of things. 1: I do not have the unit in the car (Juke 2016) as I don't trust it at the moment yet my red security dash light will not shut off even with the car running (problem with system) I still have all the connectors attached so I don't have to tear my car apart again - thoughts? 2: Did everything as described in the install guide and when it says 'press and release programming button three (3x) times) the yellow LED never flashes so I can't program the keyfob. This is where I'm stuck. Yellow LED just stays on and now I have issue number 1.

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue