Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Chad Cyr

Joined on the:

Oct. 7, 2009

Score

950

Comment(s)

11

Voted question(s)

1

Voted answer(s)

3

Votes up

0

Votes down

4

Votes up received

1

Votes down received

0

Recent Activity

Question(s) asked

6

Answered question(s)

2

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

07/12/2018

 Ford Chad Cyr (950Pts.)

1

2019 Ford F-250 Diesel

Is the EVO-FORT3 (EVO-ALL) standalone solution applicable to the 2019 Ford F-250 Diesel w/ keyless? Thanks, Chad
Login to reply View 1 answer(s)

13/11/2018

 FAQ Chad Cyr (950Pts.)

0

Flashlink Mobile Bluetooth Pairing

I have not yet been able to use my new Flashlink Mobile as it does not show up as an available Bluetooth device upon plugging it into an OBDII port. The light flashes green but BT scanning from two different phones does not find it - the phones see eachother and other BT devices in range. Is there something I am missing? Thanks.
Login to reply View 1 answer(s)

05/10/2017

 Subaru Jeremy Jedlicka (180Pts.)

0

EVO-ONE + THAR-ONE-SUB1 for 2018 CrossTrek

I just purchased a 2018 CrossTrek Premium regular key with EyeSight. Just want to verify that the EVO-ONE with the THAR-ONE-SUB1 T Harness is compatible with the new model year and the 2017 wiring information from this website will work.
Login to reply View 1 answer(s)

02/01/2017

 Subaru Chad Cyr (950Pts.)

0

EVO-ONE - Worked fine for about two weeks - Then no longer sends gnd outputs

Installed EVO-ONE in a 2015 Subaru Crosstrek PTS. Worked fine for a couple of weeks then noticed that unit no longer honked the horn nor flashed the park lights - all (-) outputs and connected as per installation guide. Swapped out with another module and everything is fine again and has been a couple of weeks since replaced and no further issues. Took the malfunctioning unit and tried it on another vehicle to test - a 2012 Toyota Tundra. Unit flashes and programs fine but will still not send (-) to flash parklights or honk the horn. Also, it will not detect the brake input to allow the programming of a Fortin 2-way RF Kit. Tried it several times with no luck. I think the unit went bad somehow but if there is anything else I can try, please let me know. Thanks, Chad
Login to reply View 1 answer(s)

02/01/2017

 Ford Chad Cyr (950Pts.)

0

EVO-ALL - "Died" after flashing/programming - No LEDs/No Longer Connects

EVO-ALL - "Died" after flashing/programming - No LEDs/No Longer Connects Updated a brand new EVO-ALL that came as part of a EVO-FORT1 kit to install into a 2015 Ford F250 pickup. After flashing and setting options/saving I connected it to the truck to program and no LEDs came on. Tried connecting back up to the updater, but it will not connect. Tried holding the programming button to do the normal reset but it shows no sign of life - Checked the connection pins and all seems fine. I grabbed another EVO-ALL I had on hand and proceeded to flash and program that unit without any issues. Could this be a bad unit that just suddenly died? I've never seen this happen.
Login to reply View 1 answer(s)

12/12/2016

 Subaru Chad Cyr (950Pts.)

0

Wiring/Programming EVO-ONE w/ DSM300 SmartStart (2015 Subaru XV Crosstrek PTS)

Installed a EVO-ONE into my 2015 Subaru XV Crosstrek w/ Push-to-Start. I have no issues with the remote starter, bypass, locks, etc. Everything works great with a Fortin 2-way RF kit - which I am still temporarily using until I figure out how to get my DSM300 Smartstart to work. I didn't find the Smartstart guide particularly useful in regards to wiring it up to the EVO-ONE for my application. I had programmed the remote start to XL202 and grounded the gray D2D mode cable as per the Fortin guide. Can someone clarify if I am to use the white D2D connector that is included with the Smartstart's multi-connector harness and does it plug into the larger antenna port? Or do I need to make up a cable to go to the black Fortin Data-Link/Flashlink Port? Do I assume that I will have to power the Smartstart separately using its own 2-wire harness w/ 3-Amp fuse since the EVO-ONE isn't providing 12-Volts from the data ports? If so, do I remove the 12V power on my connection back to the EVO-ONE? I tried powering them separately and just leaving the data wires + ground, but I could not pair the Smartstart to the EVO-ONE; I sent a lock command which the Smartstart app said was successful during the pairing process as per the instructions I found, but I couldn't get the EVO-ONE to acknowledge the signal to pair the Smartstart. I hope someone can steer me in the right direction. Thanks - Chad
Login to reply View 1 answer(s)

04/12/2016

 Toyota Chad Cyr (950Pts.)

0

2007 Avalon PTS w/ EVO-ALL - How to disable auto lights?

Just installed an EVO-ALL on 2007 Toyota Avalon w/ Push-To-Start (Smart Key). Installed in accordance with guide # 57231 REV: 20151023. Added connections for door lock/unlock and hood pinswitch. Remote starting and door locks work properly. Is there a means of disabling the Toyota "Auto Lights" when using the EVO-ALL in this configuration? (Break auto light wire, door pin trigger, etc.?) I tested the second unused set of relay contacts and they apparently aren't enabled for the task as they do not break contact on the N.C. on shutdown. Thank you for your assistance. - Chad
Login to reply View 1 answer(s)

04/12/2016

 Pontiac Mohammad Odeh (420Pts.)

0

FX64-2W WITH EVO ONE pontiac pursuit

FX64-2W not working with evo one , i connect all wires to the care it is without T harness, now when i try to program the key fob the LED on antenna not flashing it is just flash once when i connect the 4 pin blue wire small one , i am confused because the 4 pin port on evo one as chart H is for antenna which i don't have cable for it but the other blue port small i have cable for it,.
Login to reply View 1 answer(s)

04/12/2016

 Toyota Ricardo Huicochea (180Pts.)

0

Rf problem with programming

Evo one RF442W remotes. The 3x lock starts the vehicle but when trying to program the rf remotes the led on the antenna never flashes. Red led on the evo one lights up everytime i click the valet and also when pressing the brake. Ignition on, hold valet and wait for flash, press valet 5 times, press brakes.. then nothing from antenna. Are my settings wrong? Led on antenna flashes once when plugging in only
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue