Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

My fortin evo one remote starter keeps popping up check tire monitoring on 2023 kia forte

When I get in and push my start button, check my tire monitoring system keeps flashing until I hit the brake and then it stops and my car is back to normal.

0

Evo one can't function product

Hi sir I have install evo-one in my Kia sportage 2014 can't function all try ready u key bypass programming ready same no function

0

EVO-ONE: car starts, then stops, hazard lights flash 3x, then starts, then stops finally

Hey everyone! I'm using an EVO-ONE with T-Harness for the 2020 Kia Sorento PTS. When I do the 3x lock, the car turns on, then stops after a few seconds, flashes the hazard lights 3x, then turns back on, then stops after a few seconds with no hazard lights flashing. Any help would be great, thanks!

03/12/2023

Kia Mike Wes (160Pts.)

0

Remote Programming RFK441 to Evo One

I installed Evo-One with THAR-ONE-KHY1 Harness on 2009 Kia Borrego. No immobilizer. Used FlashLink to update, configured the EVO One and all seemed to go well. I dont have any factory remotes so I bought the RFK441 remote kit and RF-A2A Harness. When I plug the anntannae wire into EVO one I get one LED flash on the anntanae end. Then nothing. Turn key on and anntanae LED does not light up, Hit brake pedal 4 times and no LED lights up on anntanae dongle. I have anntane wire plugged into the evo one (blue plug). Im not using the RF-A2A harness. Am I supposed to use the harness? None of the RFK441 remotes do anything when buttons pressed. It appears the unit wont go into programming mode to allow me to connect the remotes to the unit. Any ideas? Thanks,.

30/11/2023

Kia Mike Wes (160Pts.)

0

2009 Kia Borrego With Immobilizer DeActivated

Hello, I'm installing an EVO-One with THAR-ONE-KHY1 Harness on 2009 Kia Borrego. The vehicle is equipped with immobilizer and immobilizer RFID metal ignition key but the immobilizer function has been stripped from the ECU/ECM software so the vehicle starts with any metal (properly cut) key. When I install the EVO One can I ignore the PATS Data connection and use the "Program 2: Vehicle Without PATS Data Wire" programming instructions? Thanks

26/10/2023

Kia jfehr (130Pts.)

0

Tach sensor 2009 Kia Spectra

2009 Kia Spectra. THAR-ONE-KHY1. I need to know which wire to connect the tach signal to. Yes, in the Wire Colour diagram it does tell me which wire on the ECM, but no-where can I find which wire on the EVO-one it must be connected to. I have by-passed it currently using programmable option 20.2, but the start quality is pathetic; in cold temperatures it requires more crank time, causing excessive starter drag in warmer conditions. Adjust for warm temperatures and the crank is in-sufficient for the cold mornings. Advice for me?

0

Does EVO-ONE Support Kia's New Anti-Theft Update

Hey guys,

So Kia has released a new firmware update for their cars in order to deal with the rise in car thefts. The update is applied at the dealership. I've been thinking about getting the update, but I need to make sure my Evo-One will still remote start the engine after the changes are made.

I have a 2020 Kia Forte with a push-button fob. From what I've gathered, after the update, the BMS must receive the unlock command from the KeyFob in order for the engine to start. If the car isn't unlocked and I were to try to start it, it would end up panicing for 60 seconds.

I know the EVO-One already unlocks the doors over CanBus, but does it support the update Kia is applying to our cars? Will it still remote start the car after changes are made?

 

https://www.nhtsa.gov/press-releases/hyundai-kia-campaign-prevent-vehicle-theft

0

Stuck on step 5, all 3 lights flashing Kia Niro

I am using a t-harness for install. Verified continuity on all my electrical connections. Soldered connections. During programming, I turn ignition on and red lights blink 10x as expected. Then short pause and the three LEDs all blink instead of the blue blinking indicating I'm not getting canbus communication. The COM wire was present and I verified I have the connections on the correct side of the cut. I flashed it with the most recent version of firmware and the recovered firmware, same result either way. Double checked my settings and everything kind like I'd expect it to buy correctly somethings amiss. SN-002B04 310063 This morning the car battery was dead as well

04/02/2023

Kia n h (230Pts.)

0

Key fobs won't program evo one installed in a 2013 kia soul

2013 kia soul, automatic w/o immobilizer. When entering programming I get the flashing blue light on the antenna but can not get the solid confirm light.

31/01/2023

Kia n h (230Pts.)

0

cant get can bus communication nor get the module to program without can bus signal

I cant get communication on can bus so I tried to go engine monitorless and still can not get passed programming.

27/01/2023

Kia n h (230Pts.)

0

Can't program keys or enter valet mode

Evo One won't program key fob or enter valet mode on my 2013 Kia Soul Standard Key Aoutomatic car.

0

Problem with EVO-ONE

Problem with EVO-ONE Hello everyone I buy and connect my evo-one this instruction and programming But i have some problems and questions with this product. I used this instruction https://fortin.ca/en/download/24051/24051.pdf 1. On Flashlink manager show recommended firmware 76.31 but on pdf instruction 76.60 (only works 76.31 on 76.60 not programming) 2. On my car i select diesel mode and 6 minutes running but only work 4 minutes 3. Diesel mode function 18, Delay between ignition power up and starter mode not working. ( Work without delay ) 4. My big problem. When the remote started after 4 minutes engine shut down and open my car trunk. Car: Kia Sorento 2011 Push to Start Diesel Firmware version: 76.31 and 1.26 Evo One Serial number: 002B04 138126Problem with EVO-ONE

0

What size fuse for 12v postive wire on EVO-ONE-2021 Kia Sportage push start?

Wiring diagram shows a fuse on the 12v+ wire coming from the 34 pin connector on the fuse box and going into pin E3 on the EVO, but does not specify what the fuse rating should be. What size fuse should be used?

12/12/2022