Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

15/08/2024

 Kia morgs420 (130Pts.)

0

hi there could you please reset flash limit in s/n# 001A06 535714??

Could you please reset flash limit s/n# 001A06 535714
Login to reply View 1 answer(s)

29/05/2024

 Kia chan hon kiong (130Pts.)

0

Evo one can't function product

Hi sir I have install evo-one in my Kia sportage 2014 can't function all try ready u key bypass programming ready same no function
Login to reply View 1 answer(s)

26/10/2023

 Kia jfehr (130Pts.)

0

Tach sensor 2009 Kia Spectra

2009 Kia Spectra. THAR-ONE-KHY1. I need to know which wire to connect the tach signal to. Yes, in the Wire Colour diagram it does tell me which wire on the ECM, but no-where can I find which wire on the EVO-one it must be connected to. I have by-passed it currently using programmable option 20.2, but the start quality is pathetic; in cold temperatures it requires more crank time, causing excessive starter drag in warmer conditions. Adjust for warm temperatures and the crank is in-sufficient for the cold mornings. Advice for me?
Login to reply View 1 answer(s)

20/02/2023

 Kia KC Dickinson (130Pts.)

0

Stuck on step 5, all 3 lights flashing Kia Niro

I am using a t-harness for install. Verified continuity on all my electrical connections. Soldered connections. During programming, I turn ignition on and red lights blink 10x as expected. Then short pause and the three LEDs all blink instead of the blue blinking indicating I'm not getting canbus communication. The COM wire was present and I verified I have the connections on the correct side of the cut. I flashed it with the most recent version of firmware and the recovered firmware, same result either way. Double checked my settings and everything kind like I'd expect it to buy correctly somethings amiss. SN-002B04 310063 This morning the car battery was dead as well
Login to reply View 1 answer(s)

04/02/2023

 Kia n h (230Pts.)

0

Key fobs won't program evo one installed in a 2013 kia soul

2013 kia soul, automatic w/o immobilizer. When entering programming I get the flashing blue light on the antenna but can not get the solid confirm light.
Login to reply View 1 answer(s)

31/01/2023

 Kia n h (230Pts.)

0

cant get can bus communication nor get the module to program without can bus signal

I cant get communication on can bus so I tried to go engine monitorless and still can not get passed programming.
Login to reply View 1 answer(s)

10/01/2023

 Kia n h (230Pts.)

1

Why won't my Evo-One move past step 4 on programming?

I have verified the correct firmware, proper voltage on yellow wire A1, and correct can-bus wiring.I have constant 12v with a good ground. When I turn the ignition to run the blue led that is supposed to flash 10x's turns off. I installed accordind to the install guide provided through fortin's website.I have followed the troubleshooting guide and get stuck after confirming all 5  steps

The first 3 steps in the programming are very straight forward. If you cannot pass these steps verify the following:
1- Firmware: Ensure you have flashed the correct firmware to the module as indicated in the installation guide.
2- Power & Ground: Verify the module is receiving a constant 12 volts and has a good ground.
3- Yellow Wire (A1): Verify this wire is on the correct ignition wire. Their should be 0 Volts present during the first 3 steps.

If the Blue led does not flash common issues would be the following:

1- Yellow wire (A1): Not connected to correct ignition source.
2- Can Bus Wires: If these are reversed or connected to the wrong can bus wires the module will not program.

Login to reply View 1 answer(s)

16/07/2022

 Kia Bernard St-Denis (130Pts.)

0

Add second user

The activation code is just for one person. How can I add a second user for the same car?
Login to reply View 1 answer(s)

09/02/2022

 Kia Antonio Queijo (310Pts.)

0

INSTRUCTIONS FOR KIA CEED

Do you have a Evo-All manual for a 2011 Kia Ceed?
Login to reply View 1 answer(s)

20/01/2022

 Kia Mohammad Mosa (130Pts.)

0

Do I need a to update my new EVO-ONE ..

I just purchased an EVO-ONE for my Kia Sedona 2014 (S/N: 002B04246972) and doesn’t have a bar code stamped on the back label just a Qcode and a "Secure Update" label. Q: Do I still need to use the "Flash-Link Updater" to update or reprogrammed my module? If yes, is my module compatible with”Flash-Link updater"? BTW, I got my EVO-ONE from plugnplaykits.com Many Thanks,
Login to reply View 2 answer(s)

20/01/2022

 Kia Mohammad Mosa (130Pts.)

0

Do I need a to update my new EVO-ONE ..

I just purchased an EVO-ONE for my Kia Sedona 2014 (S/N: 002B04246972) and doesn’t have a bar code stamped on the back label just a Qcode and a "Secure Update" label. Q: Do I still need to use the "Flash-Link Updater" to update or reprogrammed my module? If yes, is my module compatible with”Flash-Link updater"? BTW, I got my EVO-ONE from plugnplaykits.com Many Thanks,
Login to reply View 2 answer(s)

06/12/2021

 Kia Tom Schneider (500Pts.)

0

EVO-ONE Module not responding

Hello, I have a 2016 Kia Soul standard key. I have the EVO-ONE installed. The problem is when I try to remote start with the oem remote I am not getting any feedback at all from the bypass module. Usually the module will flash a led light. All my wires seem to be connected to the right vehicle wires and it also programmed fine when going through program option 2. Also all my settings seem to be right in the flashlink manager. Any help would be appreciated. Thanks
Login to reply View 1 answer(s)

20/10/2021

 Kia michael moore3 (130Pts.)

0

WILL THE INT-SL = WORK ON KIA AMANTI 2004

I GET ECM AND BCM BOTH GOOD
Login to reply View 1 answer(s)

25/12/2020