Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

30/12/2023

 Chrysler Amin Bakri (210Pts.)

0

programming

intalling EVO CH5 on my 2009 Chrysler Sebring. When i go to progam it to the vehicle i press the black button and plug the black connector with igition off. All 3 LEDs flash at the same time and will not go to just blue like it says it is supposed to program. I cant find the trouble shooting section to find answers
Login to reply View 1 answer(s)

15/01/2022

 Chrysler Justin Phipps (180Pts.)

0

No luck getting it to work! please help.

I have a 2016 Chryler T&C with the smart key (not push button start) I bought a evo all SN: 001A07047755. Programmed with the link (59.02 Firmware). I am using the  and Connected the yellow wires together like a guy did on youtube. I checked to make sure the yellow wire is getting power, and it has power. I get to the step with the blue light staying solid, and turn on the key and it still stays solid. I cant get it to flash when i turn the key on to program it. What should I try next? Thank you

Login to reply View 1 answer(s)

31/03/2021

 Chrysler Muqdad Altaee (130Pts.)

0

I can’t program chrt4 all light plinking

I try to program the evo but when pres the the key and connected the 4 pin all the lights are plinking and not convert to sold blue I repeated many times and re connect all the wire again
Login to reply View 1 answer(s)

05/01/2016

 Chrysler Eric Hoffmann (130Pts.)

0

Chrsyler Pacifica shuts off after a few seconds with remote start

Installed a Compustar CS300 with a Fortin INT-S+, used the suggested #7 install instructions from the Fortin install sheet. The vehicle will start for a few seconds then shut off. I took the INT-SL+ out of the car, hooked it up to the flashlink module and flashed it to 3.06 firmware. Once back in the car, held down the program button and plugged in the module, LED illuminated. Then plugged in white connector and LED stays lit. Press lock on the remote start and it goes off. Turned the key to Ignition and the LED never blinks. Still wont keep the car running. I don't think it's "learning" the car? Tried locking the doors and starting, when it shuts off the red security light on the dash blinks two fast then one.
Login to reply View 1 answer(s)

14/08/2015

 Chrysler remi caissie (230Pts.)

0

can program module

module programe in car once module need to be programe with d crypter wont programe try few atemp still the same
Login to reply View 1 answer(s)

27/12/2014

 Chrysler Frederick McWilliams (160Pts.)

0

Programmed Evo All for 3x lock Start .Will start but shutsdown after a couple seconds

2011 Town and Country
Login to reply View 1 answer(s)

25/12/2014

 Chrysler Rubin Walker (130Pts.)

0

my EVO-ALL CHAR4 programs and works 1 times

MY EVO-ALL was programmed twice the same way as discribed in the manaual. each time the unit works 1 time then stops working. I have a 2014 Chrysler town and country. Can you help?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue