Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

05/02/2025

 Infiniti q50swer (130Pts.)

0

Program help for RFK411 2015 Infiniti Q50 push to start

I purchased a 'Start-X Remote Starter Plug N Play for Infiniti Q50 14–20' on amazon, I was not satisfied with the oem key fob range so I bought the 'Fortin RFK411 1-way Rf Kit' to help out, but I have no instructions to get it work or programmed. I do have my flasher. Can somebody help me get Fortin RFK411 1-way Rf Kit working for my 2015 Infiniti q50 push to start! I need intrustions!
Login to reply View 1 answer(s)

31/01/2025

 Infiniti stephen bradley (130Pts.)

0

RFK411 programming to EVO ALL

I just purchased an RFK411 to add range to my EVO ALL, and I can’t get the key to program after completing the steps. Here is what I did, unlock door with my oem fob, remove all wiring to my Evo all, plug the 4 pin wire while holding button down until blue and red led come on then release button. Plug all wiring back to the Evo all, after all wiring are connected, press button until blue and red led turn off and then back on, then release. Turn car to on, I notice the red blue and orange light turn on, with the Evo all, and the blue led on the antenna is now rapidly flashing. I grab my single button remote and hold down button for at lease 12 seconds. At first while holding it flashes rapidly, then turns off, then a couple seconds later comes on solid blue. I release the button after that and nothing happens on the Evo all, no sounds are heard. I don’t think my Evo all completed the programming. I tried switching to my other remote and still same result. Any help or steps to try is appreciated. Car is Infiniti g37 auto with push to start. Prior to adding the rfk411, I was only using the Evo all with remote start using the x3 press with oem fob with no problems, still starts fine with oem fob. Kit included t harness. I am using the Fortin harness rfa2a with the antenna.
Login to reply View 1 answer(s)

14/01/2025

 Infiniti SlimDrives360 (150Pts.)

0

All keys lost programed new fobs remote start cranks but not starting

Hired to do reprogram fobs 2014 infinti Q50 All keys lost reprogramed new fob all buttons work however now remote start problem car cranks but no start. Evo-all 2018, infiniti q50 2014.
Login to reply View 1 answer(s)

30/10/2024

 Infiniti gabriel crispin (140Pts.)

0

How to set up for telematic app

I try to install the app telematic to use with fortin
Login to reply View 0 answer(s)

28/12/2023

 Infiniti Garrett Young (150Pts.)

0

Module unable to sample vehicle immobilizer data

2005 G35 standard key EVO ALL S/N 001A07 501715 Crime Stopper RS7 remote start I have several documents with programming procedures. I am able to get through these at which point the bypass module flashes red and yellow. I unplug it, take it to the computer for decrytor and it comes back saying unable to sample the vehicles immobilizer data. I have tried re selecting the options in flashlink manager, re flashing the evo all, and re trying the programming features to no avail. It will not decrypt.
Login to reply View 1 answer(s)

07/12/2022

 Infiniti mike st-pierre (130Pts.)

0

evo-all flash jaune et rouge apres avoir programmer l'antenne evo-start 2

J'ai achete evo-all pour avoir un demarreur a distance sur la cle oem mais il manquais de distance alors jai acheter l'antenne evo start 2 toute fonctionnais il decollait apres 3 lock mais apres avoir programmer l'antenne evo start 2 mon module evo all flash rouge et jaune meme apres avoir deconnecter le connecteur 4 pin mais quand je clique sur verouiller ou deverouiller les porte la lumiere de lantenne allume verte mais il ce passe rien
Login to reply View 1 answer(s)

27/02/2021

 Infiniti ian yadao (130Pts.)

0

G37 programming module

I'm trying to install an EVO-ALL remote start on my g37. Already tapped into the push-to-start button and made the T-Harness connections with the OBDII, keyport, and brake switch. Tried programming the module but when I inserted my key fob into the key port, the dash is saying to remove the key. Closed the door, that got rid of the light, but while I was going through the programming steps, I can't get pass step 4. I press the PTS button to turn car to ACC mode, but module does not flash red or blue. IT only stays solid yellow. I've already flashed the module with the flashlink 4. & i'm pretty sure the connection between the ignition and PTS wire is good. Idk what do. any help?
Login to reply View 1 answer(s)

22/05/2020

 Infiniti David Suen (130Pts.)

0

Can't Program

2015 Q50 Non hybrid. I connected all the wires from the EVO-NIST4 T Harness to the BCM properly. The car could also start fine. I used the Flashlink to program the Remote Starter. Then when i Connect the Black Connector to the box inside the car. nothing happens. I rechecked all my connections and the car starts fine with no issues, it's just that it can't power the black box. no lights in any of the 3 indicators. When I connect it to the computer through the Flash Link there isn't any program. Do I have a faulty harness?
Login to reply View 1 answer(s)

19/10/2019

 Infiniti BLourenco (130Pts.)

0

'12 G37 - Is my EVO-ALL broken?

[EVO-ALL install on 2012 Infiniti G37 w/ THarness; SN/001A07 008704; Guide #80851] Issue: Cannot program the EVO-ALL. I get stuck on step 2. When I press the button twice, the yellow LED doesn't start blinking. In addition: 1) I noticed if I remove the data link cable from the EVO-ALL while the white 20-pin connector is installed, the locks contantly go off (always locking). I have gone over the wiring many times and am confident it's correct. 2) During step 1, I have to disconnect and reconnect the data link cable several times before it finally begins cycling through the LEDs. Is this normal? or is it asign of bad wiring? bad unit?
Login to reply View 1 answer(s)

08/10/2019

 Infiniti Kevin Lay (390Pts.)

0

Dcryptor

Need a Dcryptor reset please and flasher aswell, Also cant get my evo one to get pass step 4. Any help will be much appreciated. Can bus connected, do i need to connect anything else? SN=002B04 013259
Login to reply View 1 answer(s)

16/09/2019

 Infiniti Denis T (130Pts.)

0

2015 Q50 - The immobilizer bipass being sent to unit

How long does the process normally take? It has been updating now for over an hour. Is that normal?
Login to reply View 1 answer(s)

26/03/2019

 Infiniti Henry Cerda (180Pts.)

0

2015 Infiniti Q50

Does the Evo all capable of starting Ac in my car when it’s started? What hardware do I need for this?
Login to reply View 1 answer(s)

18/02/2019

 Infiniti DavidF O'Sullivan (210Pts.)

0

Why won’t the EVO-ALL program in my 2013 Infiniti M37?

Standalone installation with T harness. I follow the steps exactly as they are written. Step 6 says hold key by start button and step on brake. Step 7 is the exact same process, but the BLUE and RED LEDs should illuminate. The RED illuminates briefly before turning off, and only the blue remains. The rest of the process does not work and the BLUE LED stays solid. In addition to this, the security/Immobilizer light on my dash is on solid when the car is running. Please, can anyone offer assistance?
Login to reply View 0 answer(s)

05/02/2019

 Infiniti Nick Larsen (160Pts.)

0

2009 Infinity G37 OEM remote No Start

I just finished installing the EVO-NIST1 (no other components) on my 2009 Infinity G37. After hooking up the wiring harness I completed the bypass programming procedure and everything went good until I tried to start the car using my OEM remote. I pushed my OEM remote 3 times and the car did not start. Each time I pushed the lock button a blue LED light flashes on the EVO unit but nothing else happens. Do I need to order a stand alone remote? Do I need additional components? Not sure what to do here.
Login to reply View 1 answer(s)

10/10/2018

 Infiniti sung won lee (260Pts.)

0

fortin eve key update limit

i want my work back from the beginning. everywhere is a mess. module and flash link factory initialization.
Login to reply View 1 answer(s)

12/02/2017

 Infiniti Kirill Wildgrube (130Pts.)

0

G37: Unable to program - solid red light as soon as datalink is plugged in

As soon as I plug in the datalink cable, I get a solid red LED.

his happens if I hold the program button, or not.  Unable to do master reset or continue with programming, as the unit doesn't do anything besides display one solid red LED.  No other plug is plugged in... 

2010 Infiniti G37 sedan. EVO-NIST1 

Login to reply View 2 answer(s)

12/02/2017

 Infiniti Kirill Wildgrube (130Pts.)

0

G37: Unable to program - solid red light as soon as datalink is plugged in

As soon as I plug in the datalink cable, I get a solid red LED.

his happens if I hold the program button, or not.  Unable to do master reset or continue with programming, as the unit doesn't do anything besides display one solid red LED.  No other plug is plugged in... 

2010 Infiniti G37 sedan. EVO-NIST1 

Login to reply View 2 answer(s)

01/02/2016

 Infiniti Frankie Aladi (160Pts.)

0

2011 Infinity QX56 Programing EVO-ALL & THAR-NIS1 Stand Alone

Car 2011 QX56 EVO-ALL & THAR-NIS1 Stand Alone Service # 001 A06 585175 Guide #12681 During programing when I get to #7 The red sometimes turns off and only blue is on. I have only been able to get both red and blue to stay on twice very briefly. In the instances when they stayed on, following the next step #8, Pressing the start and stop button x2 does not turn on the ignition. If you press it a third time or jump to #9 the the inginition turns on and it flashes rapidly. If I go continue with the programing, the result is that the car does not remote start on pressing 3 times. Basically nothing happens, it simply locks the door 3 times. I have an updated firmware. Did the update all over again yesterday successfully. I have been on this thing for the past 2 days. Have not done anything else all weekend. I am at my wits end with this thing. Somebody help.
Login to reply View 2 answer(s)

01/02/2016

 Infiniti Frankie Aladi (160Pts.)

0

2011 Infinity QX56 Programing EVO-ALL & THAR-NIS1 Stand Alone

Car 2011 QX56 EVO-ALL & THAR-NIS1 Stand Alone Service # 001 A06 585175 Guide #12681 During programing when I get to #7 The red sometimes turns off and only blue is on. I have only been able to get both red and blue to stay on twice very briefly. In the instances when they stayed on, following the next step #8, Pressing the start and stop button x2 does not turn on the ignition. If you press it a third time or jump to #9 the the inginition turns on and it flashes rapidly. If I go continue with the programing, the result is that the car does not remote start on pressing 3 times. Basically nothing happens, it simply locks the door 3 times. I have an updated firmware. Did the update all over again yesterday successfully. I have been on this thing for the past 2 days. Have not done anything else all weekend. I am at my wits end with this thing. Somebody help.
Login to reply View 2 answer(s)

11/10/2015

 Infiniti Jose Miramontes (210Pts.)

0

2007 G35 Evo All Programing Not Flashing blue

I installed the EVO ALL with T-Harness and a Viper remote start to my 2007 Infiniti G35. As I follow the programing instructions, I get to the part (step 6 of programing) where I'm suppose to push the PTS and wait for the blue light to flash rapidly, well the blue light does not come on or flash. what should I be checking?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue