Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

How to set up for telematic app

I try to install the app telematic to use with fortin

0

Module unable to sample vehicle immobilizer data

2005 G35 standard key EVO ALL S/N 001A07 501715 Crime Stopper RS7 remote start I have several documents with programming procedures. I am able to get through these at which point the bypass module flashes red and yellow. I unplug it, take it to the computer for decrytor and it comes back saying unable to sample the vehicles immobilizer data. I have tried re selecting the options in flashlink manager, re flashing the evo all, and re trying the programming features to no avail. It will not decrypt.

0

evo-all flash jaune et rouge apres avoir programmer l'antenne evo-start 2

J'ai achete evo-all pour avoir un demarreur a distance sur la cle oem mais il manquais de distance alors jai acheter l'antenne evo start 2 toute fonctionnais il decollait apres 3 lock mais apres avoir programmer l'antenne evo start 2 mon module evo all flash rouge et jaune meme apres avoir deconnecter le connecteur 4 pin mais quand je clique sur verouiller ou deverouiller les porte la lumiere de lantenne allume verte mais il ce passe rien

0

G37 programming module

I'm trying to install an EVO-ALL remote start on my g37. Already tapped into the push-to-start button and made the T-Harness connections with the OBDII, keyport, and brake switch. Tried programming the module but when I inserted my key fob into the key port, the dash is saying to remove the key. Closed the door, that got rid of the light, but while I was going through the programming steps, I can't get pass step 4. I press the PTS button to turn car to ACC mode, but module does not flash red or blue. IT only stays solid yellow. I've already flashed the module with the flashlink 4. & i'm pretty sure the connection between the ignition and PTS wire is good. Idk what do. any help?

0

Can't Program

2015 Q50 Non hybrid. I connected all the wires from the EVO-NIST4 T Harness to the BCM properly. The car could also start fine. I used the Flashlink to program the Remote Starter. Then when i Connect the Black Connector to the box inside the car. nothing happens. I rechecked all my connections and the car starts fine with no issues, it's just that it can't power the black box. no lights in any of the 3 indicators. When I connect it to the computer through the Flash Link there isn't any program. Do I have a faulty harness?

0

'12 G37 - Is my EVO-ALL broken?

[EVO-ALL install on 2012 Infiniti G37 w/ THarness; SN/001A07 008704; Guide #80851] Issue: Cannot program the EVO-ALL. I get stuck on step 2. When I press the button twice, the yellow LED doesn't start blinking. In addition: 1) I noticed if I remove the data link cable from the EVO-ALL while the white 20-pin connector is installed, the locks contantly go off (always locking). I have gone over the wiring many times and am confident it's correct. 2) During step 1, I have to disconnect and reconnect the data link cable several times before it finally begins cycling through the LEDs. Is this normal? or is it asign of bad wiring? bad unit?

0

Dcryptor

Need a Dcryptor reset please and flasher aswell, Also cant get my evo one to get pass step 4. Any help will be much appreciated. Can bus connected, do i need to connect anything else? SN=002B04 013259

0

2015 Q50 - The immobilizer bipass being sent to unit

How long does the process normally take? It has been updating now for over an hour. Is that normal?

0

2015 Infiniti Q50

Does the Evo all capable of starting Ac in my car when it’s started? What hardware do I need for this?

0

Why won’t the EVO-ALL program in my 2013 Infiniti M37?

Standalone installation with T harness. I follow the steps exactly as they are written. Step 6 says hold key by start button and step on brake. Step 7 is the exact same process, but the BLUE and RED LEDs should illuminate. The RED illuminates briefly before turning off, and only the blue remains. The rest of the process does not work and the BLUE LED stays solid. In addition to this, the security/Immobilizer light on my dash is on solid when the car is running. Please, can anyone offer assistance?

0

2009 Infinity G37 OEM remote No Start

I just finished installing the EVO-NIST1 (no other components) on my 2009 Infinity G37. After hooking up the wiring harness I completed the bypass programming procedure and everything went good until I tried to start the car using my OEM remote. I pushed my OEM remote 3 times and the car did not start. Each time I pushed the lock button a blue LED light flashes on the EVO unit but nothing else happens. Do I need to order a stand alone remote? Do I need additional components? Not sure what to do here.

0

fortin eve key update limit

i want my work back from the beginning. everywhere is a mess. module and flash link factory initialization.

0

G37: Unable to program - solid red light as soon as datalink is plugged in

As soon as I plug in the datalink cable, I get a solid red LED.

his happens if I hold the program button, or not.  Unable to do master reset or continue with programming, as the unit doesn't do anything besides display one solid red LED.  No other plug is plugged in... 

2010 Infiniti G37 sedan. EVO-NIST1 

12/02/2017