Questions & Réponses

2014 ram 1500 (standard key start) after successful programming, vehicle can be remote started by 3x lock only....H2 - fortin 2 is selected on in flashlink setting, ascl6 app protocol is set to fortin, RFA2A adaptor is connected but still no luck, both red and green led on ascl6 are on solid, been trying to get the evo all to pair with ascl6 with no success.

evo all led lights are stuck at step 8, will not go to step 9 

1 - Disconnect the Black 4 pin power connector from the Evo-All.

2 - Press and Hold the Programming button on the Evo-All while plugging back the Black 4 pin connector.

3 - The LED’s on the Evo-All will begin to cycle. Keep pressing the programming button until the RED and BLUE LED’s are On.

4 - Release the programming button.

5 - Press and Hold the programming button again for 5 seconds. The BLUE and RED LED’s will blink once.

6 - Release the programming button.

7 - Cycle the ignition to the ON position.

8 - The RED, YELLOW and BLUE LED’s will be ON.

9 - Seconds later the RED and BLUE LED’s will blink once to confirm that the MyCar ID has been learned to the Evo-All.

10 - Cycle the vehicle’s ignition to the OFF position to Exit EVO-ALL programming.

Today I tried installing the Evo-All to a 2016 Ram 3500 diesel using the T-harness. I made it to step 7 and could not get past that. 

In step 7 it says “No key = Red” and “Key in= Red and blue”. Whenever i put the key in, the red and blue will stay on for a few seconds then only the blue will stay on. Is this supposed to happen?

I then put it into the RUN position but it will not flash rapidly. If I put it back into OFF, the blue will go back to solid.I checked the CANBUS wires multiple times and made sure they were at the right spot. I even switched them. In step 8 it says “ignition off= red” and “ignition on= red and blue off”. I dont see a red light after step 7 but the blue does turn off when the ignition is on.  One thing I did notice though was that the CAN-HIGH wire Grey/White Pin6 on the guide is a different color on my truck; its sort of a tan color but it is still pin 6. The yellow wire DOES match up. Would this have to do with anything?

I followed the intructions on how to test the CANBUS connection and ignition(https://fortin.ca/en/qa/403/programming-evo-all). The ignition is good but whenever I put it in RUN, the blue light will not flash so im sure its a CANBUS problem i just cannot figure out what it is. I also tried resetting the module and it did not work. I updated  it to the latest firmware and even dropped it down to the one it says on the guide but that did not work either. I also tried waiting in between the steps and no luck. Any help is appreciated. 

2019 Ram 1500 push to start Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

VIN: 1C6RREFT6KN568083

Hardware version is 6.0  

Firmware version is 63.[01]  

flash limit 2/8  

Have tested contunity on all leads for completeness, wires are in the correct place and not incorectly tied.  

Flash Link  

Hardware version 4.0  

Firmware version 4.[05]

I have tried pressing unlock on oem remote when blue is flashing and ignition is off.

Outcome: Truck responds by unlocking doors and blue led is still flashing rapidly.  

I have tried resetting the unit and attempted to program. I also toggled push to start on and attempted to program as well.

Outcome: I am still Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

I am still unable to get past step 6.

Fortin, what are the proper channels I can use to esclate this matter further. It has been several months of back and forth with no progress. I feel the only other way to get through to you would be by sharing my emabrising expierence on social media platforms. Before I do let me ask one last time...please help. 

Best,

Dylan Davila

2019 Ram 1500 push to start Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

VIN: 1C6RREFT6KN568083

Hardware version is 6.0  

Firmware version is 63.[01]  

flash limit 2/8  

Have tested contunity on all leads for completeness, wires are in the correct place and not incorectly tied.  

Flash Link  

Hardware version 4.0  

Firmware version 4.[05]

I have tried pressing unlock on oem remote when blue is flashing and ignition is off.

Outcome: Truck responds by unlocking doors and blue led is still flashing rapidly.  

I have tried resetting the unit and attempted to program. I also toggled push to start on and attempted to program as well.

Outcome: I am still Unable to get past step 6 blue led will not stop flashing when Start/Stop button is pressed to turn off ignition.

I am still unable to get past step 6.

Fortin, what are the proper channels I can use to esclate this matter further. It has been several months of back and forth with no progress. I feel the only other way to get through to you would be by sharing my emabrising expierence on social media platforms. Before I do let me ask one last time...please help. 

Best,

Dylan Davila