Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

infiniti evo-all---evo-key

Hello. Is there a diagram (better if it is standalone) for evo-all such a connection on 2015 infinity Q50, like evo-key? By RX-TX

0

2004 QX56

Will 3x-lock remote start work on a 2004 infiniti QX56? (evo-one)

0

EVO-ALL THAR-NIS1 (when the engine is running, the standard keychain does not work)

I have Infiniti G37S coupe 2009 on the European market, everything is connected by the manual, but when the engine is running, the standard key fob does not work, you can open the car only with a metal key, just when you open the door, does the engine stall, what did I do wrong?

0

Add ASCL6 with RFK942

I've installed the EVO ALL with T-Harness (EVO NIST4) and the RFK942 RF kit to my 2016 Infiniti Q50 (3.0T). All works well. I am considering adding the Car Link ASCL6 system to my car. My question is can I use the RFK942 together with the Car Link or will I have to choose between one or the other If I can use both, will I need something added to the existing T-Harness (EVO NIST4) in order to connect them both (such as RFA2A)? Thank you in advance for your help.

0

infiniti q50

Hello. For 2014 Infiniti Q50 I installed evo-all ... 001A07137445 ... The program was successful (both in the car and in the decryptor too). But when press the factory remote control, the blue light on the module does not light up ... When the ignition is open, the yellow light does not light up either. Then I installed another module and everything was fine. They probably sold me the spoiled one, right?

0

2017 Infiniti QX70 WILL NOT START.

I have a 2017 Infiniti QX70 with Evo-all and T-harness standalone installation. Will not start after press lock 3x, all the lights come on just won't crank at all. Re-install with new Evo-Nist1 Kit still same problem. Please help.

0

2016 Infiniti QX70 EVO-NIST1 Stand-Alone Add-On Remote Start -Brake Problem

2016 Infinit QX70 EVO-NIST1 Stand-Alone Add-On Remote Start is the Vehicle and Product that is being installed (with harness - not hard wired) 

I have confirmed the EVO ALL is configured and programed for the vehicle - no RF controller, stand alone, factory remote (push lock, unlock, lock to start).

I installed the fortin harness and hooked up the PST wire, the park light interface wire, and the vallet switch.  I am using the install instructions; Guide #90131

I have successfully programed the unit to the vehicle; yet the problem is the engine will not start.

When I attempt a remote start cycle, the parking lights activate, the radio headunit turns on, the PST engages to ACC, and then the gauge cluster appears on the dash (digital), and then the PST engages to Start (ignition).

But then the vehicle does not start. 

If I attempt a remote start in the car while pressing the brake pedal; the system activates.

The brake lights currently function - yet during the remote start cycle, the Fortun system is NOT activating the brake lights during the start up cycle.  This appears to be the failure point.

I have checked the connections from the Fortin Product to the brake light switch.  I have tried to reset the connection and it is secure.  There is no way of reserving the connections. 

And per the self help instructions I have not hooked up any other unnessacry Fortin connections.

I am using the RL2 connector to the EVO ALL unit.

I have also confirmed the the vallet switch installed (dark blue) is  not grounded or closed during the remote start cycle.

I have read a post where a 2016 Juke had a similar problem where the wires coming from the  Fortin  Harness were reversed to the factory brake light switch.

Can someone confirm my theory that the problem is the EVO ALL unit is not sending the brake signal during the remote start cycle to the corresponding brake light factory harness?  Is it the case where the Fortin plug which connects to the factory brake light  swith is missed wired?

I have spent a total of 6 hours of my last two weekends confirming connections, voltage, updating the software versions, and programing the unit but I am stuck at this failure point.

Any kind words or assistance would be helpful.

Thanks!

1

Is the 2020 Infiniti QX60 the same as the 2018 and 2019?

1

Is the 2020 Infiniti QX60 the same as the 2018 and 2019?

0

2009 Infinity G37 OEM remote No Start

I just finished installing the EVO-NIST1 (no other components) on my 2009 Infinity G37. After hooking up the wiring harness I completed the bypass programming procedure and everything went good until I tried to start the car using my OEM remote. I pushed my OEM remote 3 times and the car did not start. Each time I pushed the lock button a blue LED light flashes on the EVO unit but nothing else happens. Do I need to order a stand alone remote? Do I need additional components? Not sure what to do here.

0

Infiniti g37 2009 car not starting with the oem remote x3

I have ifiniti G37 2009 with push button, i bought the Evo Nist 1 as recommended with the Tharness and the flash link, i selected the x3 oem lock button from the unit options and did all the settings correctly, after connecting all the wires and plugs as per the catalogue ive done the programming as well and when im pressing lock the led blue light is turning on, pressing 3 times but the car is not turning on, ive noticed that the brake light is not turning on, but when i give pulse for the yellow and black wire the engine is starting, i need help please i was working for like 5 hours trying to solve it and checking the other people questions, please assist asap as i made a mess :(

0

Infiniti g37 2009 car not starting with the oem remote x3

I have ifiniti G37 2009 with push button, i bought the Evo Nist 1 as recommended with the Tharness and the flash link, i selected the x3 oem lock button from the unit options and did all the settings correctly, after connecting all the wires and plugs as per the catalogue ive done the programming as well and when im pressing lock the led blue light is turning on, pressing 3 times but the car is not turning on, ive noticed that the brake light is not turning on, but when i give pulse for the yellow and black wire the engine is starting, i need help please i was working for like 5 hours trying to solve it and checking the other people questions, please assist asap as i made a mess :(

1

evo-all + DSM300 Smartstart

I have a 2009 Infiniti FX35 with evo-all with the T-harnes and added a Directed DSM300 smartstart module. I have two issues; 1) when I remote start the car everything is fine and the doors remain locked. When I remote shutoff the car, the doors unlock. Is that supposed to happen? It happens with both the smartstart and 3X lock method. I'm worried that after the 15 minute timer is up on the start and it shutsdown, the doors will unlock. 2) the smartstart will start the car but I can not unlock and lock the doors, I have plugged the unlock/lock wires into the bcm and when I test the lock/unlock on the smartstart, the blue light flashes once so I'm pretty sure its getting the signal from the smartstart module. But the doors dont lock or unlock, could this be a grounding issue or something?