Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

EVO-ONE: car starts, then stops, hazard lights flash 3x, then starts, then stops finally

Hey everyone! I'm using an EVO-ONE with T-Harness for the 2020 Kia Sorento PTS. When I do the 3x lock, the car turns on, then stops after a few seconds, flashes the hazard lights 3x, then turns back on, then stops after a few seconds with no hazard lights flashing. Any help would be great, thanks!

0

HEADLIGHTS FLASHING when entering vehicle AFTER 3xstart and 15min run time is met

2016 kia sedona ex push to start t-harness When entering the vehicle after using 3xstart and 15 min run time ends- OR starting using push to start button- the vehicle is flashing headlights/tails only. Vehicle will start- but the headlight indicator on insturment cluster lights in unison with the headlights/tails. The vehicle will start and have no flashing lights using the 3x press on remote. Is there a toggle that is active that should not be? I am current on software version. I did need to toggle 3x press on so the vehcle would use remote - folliwin the installation instructions .

0

2018 Kia Niro Hybrid PTS, after installation NO lights on cluster no power

2018 Kia Niro PTS Hybrid brand new installing Evo One for X3 Lock. No power on the car at all i check the installation and everything seems fine... but no power on the car at all..

0

2018 Kia Niro Hybrid PTS, after installation NO lights on cluster no power

2018 Kia Niro PTS Hybrid brand new installing Evo One for X3 Lock. No power on the car at all i check the installation and everything seems fine... but no power on the car at all..

0

No dash power no crank

2014 Kia Optima pts no dash lights no crank on rs. Unit blinks blue when I press lock 3x remote starter clicks 2x and I get 2 led flash error on rs saying hood pin switch but it isn't even hooked up yet. Me evo all came pre programmed with c1,d6,program lock checked off with a version of 76 46 is this the correct programming?

0

Do I need RF kit or oem remote should remote start the vehicle?

Do I need RF kit or oem remote should remote start the vehicle? 2013 kia rio 5 s/n 002B04010497

18/10/2019

Kia Alex Za (220Pts.)

0

OEM remote range during RS operation is drastically low

KIA Sedona 2016 Evo One with 3xlock start with OEM key fob Evo One causes some RF interference in the system for OEM key fobs when RS is operating. I can start the car from a distance of probably 300 feet, but if i want to shut it of, it does not deliver the signal unless I come at least 30 feet to the car. Any Idea what option in EVO One can cause such an interference?

1

Can't turn off Kia Niro

After remote start, I enter the car with the smart key but when I press the push start button nothing happens to indicate the takeover happened (light on push to start button off), if I press the brakes nothing happens (but I can drive) but if I want to turn the car off, I press the button and it says to press the pedal to turn on (but the car is on and I can drive). No matter what I do (press repeatedly, press brakes, put in drive), I can't turn off. I believe the take over is only happening after the 15 minutes of the remote start is over. One detail is that only then my headlights if on auto mode will turn on (I can turn on manually). Any ideas? Evo one, Niro 2019, latest firmware loaded.

0

2014 Kia Forte EX PTS VIN8 A Couple of Questions

1st I used Guide 24661 for Evo ONE and 68731 for FL4 when installing the EVO One (recommended firmware identified on program screen, its higher than 76.36, i think there are two newer firms but it wont let me click on them, one is a beta ver.) in car to include adding 2-1 amp diodes at PTS. The car is loaded with options, heated front rear, ac front driver seat, nav and tech pack and more. So I connected laptop to FL(ver 4.05 and recomended in program screen) and FL4 to bypass/ RS and logged in, I dont see the toggle in the lower right corner they speak of, instead I can just click on the tab at top of screen and it asks to confirm or cancel(if you changed anything and didnt save) to switch between bypass and RS. Right now 3x locks the car will crank over but no run, my seat moves, Headlights and dash light up, air controls work, and radio comes on then I hear a couple clicks then the car starts to crank but acks like no fuel, What are all the settings I should have on in the bypass and starter options? I think I had to choose 2.4 in order to get it to even crank, What am i missing or need to check 2nd I see the bypass/starter has a programming set of intructions and the FL4 has its own programming setup however when save and loading setup in user interface when all devices are connected together inline, I get a message stating 20.6 will be changed but it was already defaulted with a green thumbs up, also in bypass I get a message that alot will change when those are also already defaulted with a green thumbs up...smh. Question is how do the options 2.Programmable Option and 31.4,5 and 6 work in unison with each other? Side note while creating this I just realized I did nothing with the decrypt after every thing is done with bypass and RS do i need to click send on the decrypt screen, what is the complete steps in order to complete this. Connect laptop-FL4-Bypass/RS, login, choose settings and load(save), then decrypt, then just unplug, then test or...? Update: I dont think i have a decrypt option...

21/09/2018

Kia minh dao (430Pts.)

0

remote start

! good morning. I have a 2015 sedona standard key to be install with evo-one. Is it suppose stand alone?how can i remote start? ty

0

2017 Kia Sedona PTS EVO-ONE: 3x lock starter issue

Video of Issue

 

I'm having an issue with my 3x lock remote start function after installation on my 2017 Kia Sedona Push-to-Start.  It attempts to start, but the starter keeping trying to turn for about 8 seconds straight, doesn't start successfully, and then the parking lights flash 3 times.  The car then locks, waits about 5 seconds, and goes through the same sequence a second time and gives the same 3x flashes on parking lights.

 

I don't know if the 3x parking light flashing error is considered before start or after start in this case, as they mean two different things.

 

Any idea what the issue is?  It almost sounds like the car's trying to start but either the spark plugs or the fuel line isn't feeding, which I'm guessing means that the immobilizer is still enabled.  I checked all the wire connections and they are good, so I'm not sure what the issue is.

 

Details

Firmware: 76.39

C1 Status: Enabled

38.2 Status: Enabled

EVO-ONE Yellow Wire: Cut

Remote: OEM

Car Model: 2017 Kia Sedona PTS

Parking Light Error: 3x flashes after attempted start

Vehicle Miles: 3,500 (it's a new car)

Transmission: Automatic

 

Any help would be great, thanks!

0

Evo One - 2015 Kia Optima - Passes setup, but won't remote start.

Evo One installed on 2015 Kia optima push to start. It passes setup, but will not remote start. I get the first lock with a beep, then a lock with the horn, and the third key press, is just another horn beep. I have checked and rechecked connections, but obviously I have something wrong. I have programed (computer) for the 3X start and yellow "loop" is clipped. Fortunately the car still operates normally ottherwise. Any help is greatly appreciated. I look forward to being able to use the remote start,

0

Evo One - 2015 Kia Optima - Passes setup, but won't remote start.

Evo One installed on 2015 Kia optima push to start. It passes setup, but will not remote start. I get the first lock with a beep, then a lock with the horn, and the third key press, is just another horn beep. I have checked and rechecked connections, but obviously I have something wrong. I have programed (computer) for the 3X start and yellow "loop" is clipped. Fortunately the car still operates normally ottherwise. Any help is greatly appreciated. I look forward to being able to use the remote start,

16/09/2017