Questions & Answers

Login to reply View 1 answer(s)

11/02/2022

Chevrolet Steven Lukasik (130Pts.)

0

2003 suburban evo one install. Programs perfectly fine but won’t remote start. No lights flash while remote starting

Programmed perfectly. Changed all options for bypass and remote start on flash manager for 3x remote lock start. When hitting lock on remote no blue light on module. Also no lights at all when trying remote start. When key is on ignition or running module shows yellow light. All troubleshooting points to either no GWR signal or bad can signal. There is no GWR wire in schematic. Any help would be great

evo-one

Login to reply View 1 answer(s)

21/12/2021

Chevrolet Victor Burisch (130Pts.)

0

2014 Tahoe EVO-ALL no crank

Have the EVO-ALL installed with T-Harness in a 2014 Tahoe. After car is shut off with the key and remote start is attempted vehicle will start as it should. Any other time you attempt to remote start the vehicle it will go through the motions and power on ignition but will not crank. it makes two attempts and then shuts down with the 3 light flash. the ignition powers on and then goes out as if it was going to attempt to start but it does nothing. if i restart the vehicle with the key, turn it off and attempt again it will rempote start one time

oem-remote

stand-alone

Login to reply View 1 answer(s)

19/12/2021

Chevrolet Wyatt Schmitt (160Pts.)

0

Remote start doesnt work after unplugging module.

I installed the remote start programming and it works when it is all hooked up. But when I unplug the module and plug back in my cars original plugs and close the circuit it stops working. How would i go about fixing this.

evo-all

3x-lock-start

Login to reply View 0 answer(s)

19/12/2021

Chevrolet Jacob Landis (130Pts.)

0

Remote Start not working after programming

Just finished installing the remote starter kit on my 2019 Silverado 1500 LD. Followed all the instructions and everything went exactly as desicribed in the manual. After programming and reinstalling the RS Module, the truck will not remote start. No LEDs lighting up when I push the lock button 3x as instructed.

Login to reply View 1 answer(s)

10/11/2021

Chevrolet Nicholas Girard (150Pts.)

0

EVO-ALL standalone install 2002 Chevrolet Silverado

Can the EVO-ALL function as a remote starter in a standalone install? (3x start OEM key) Or is this a bypass unit only? Where I need a seperate remote starter. This is for a 2002 Chevrolet Silverado, standard key.

Login to reply View 2 answer(s)

10/11/2021

Chevrolet Nicholas Girard (150Pts.)

0

EVO-ALL standalone install 2002 Chevrolet Silverado

Can the EVO-ALL function as a remote starter in a standalone install? (3x start OEM key) Or is this a bypass unit only? Where I need a seperate remote starter. This is for a 2002 Chevrolet Silverado, standard key.

Login to reply View 2 answer(s)

24/10/2021

Chevrolet eric maldonado (270Pts.)

0

13 Silverado remote start

Istalling a evo all stand alone on a 13 Silverado 3500 with stardard key with OEM Remote starter, program evo ok dash light will come on but no crank or start. Instal with Thar-GM4.

Login to reply View 1 answer(s)

03/03/2021

Chevrolet getzys (160Pts.)

0

dose not turn off when pressing the brake pedal

2020 chevy traverse dose not turn off when pressing the brake pedal installed on 3 chevy travers all 3 dose the same thing

Login to reply View 2 answer(s)

03/03/2021

Chevrolet getzys (160Pts.)

0

dose not turn off when pressing the brake pedal

2020 chevy traverse dose not turn off when pressing the brake pedal installed on 3 chevy travers all 3 dose the same thing

Login to reply View 2 answer(s)

03/02/2021

Chevrolet Andrew Peckham (170Pts.)

1

2008 Silverado 2500hd starts fine with the 3x lock button, if started with key I get a security light

I am using the EVO-GMT4 which comes with the T-harness. 2008 2500HD 6.6 Duramax WT with standard key. All programing went fine, after initial installtion had a fuse blow - under hood DIS 2.5A fuse - replaced and system works with 3x lock button on factory remote. If I key start the truck I get a security light on the dash, stays on solid the entire time. Truck runs fine just has the annyoing light on the dash. Have not pulled the code for the light yet as it goes out if I start with the 3x lock feature. Any suggestions?

Login to reply View 0 answer(s)

02/12/2020

Chevrolet John Faz (130Pts.)

0

OEM 3x Lock not starting 2011 Silverado 1500

EVO-GMT4

2011 Silverado 1500 Standard-Key. Programmed according to instructions on guide #59011. Installed using the included T-Harness. Programmed and decrypted using USB Flash Link. Re installed the module into vehicle. When I push the lock button on the OEM remote 3x the blue light flashes each time but doesn't start the vehicle.

Login to reply View 1 answer(s)

30/08/2020

Chevrolet David Brehmer (130Pts.)

0

2020 Colorado RF Kit disrupts Daytime Running Lights

I have a suuccessful installation. Everything works: remote start, lock/unlock, with the OEM key fob (x3 lock remote start) and the RF442 Kit. The only isssue is that when the RF442 is used to either unlock or remote start the vehicle, the DRL's do not function as OEM intended. The DRL's are the low beams with low poer output. With the OEM remote, everything act's normal, however, with the RF Kit, the low beams simply turn on to full brightness (not low power like it should). I have set the parking lights control in the firmware to both on and off, both with the same issue. In addition, the RF Kit does not 'flash' the vehicle lights to confirm lock or unlock and does not turn on parking lights to indicat the vehicle is running (under remote start conditions).

oem-remote-monitoring

Login to reply View 1 answer(s)

17/08/2020

Chevrolet Brian Swann (130Pts.)

0

2010 Tahoe. Installed,setup, decrypted. Alll went well. Push Lock 3X, nothing.

I bought this truck used 2 years ago. Just noticed I have a Directed 3902T CANBUS OEM Security Upgrade System installed. Could this somehow causing the vehicle not to start? If so, is there some kind of workaround? Also, when I push the lock button the first time, on the dash, a light with a vehicle and a padlock flashes on the screen and stays lit.

3x-lock-start

Login to reply View 1 answer(s)

30/10/2019

Chevrolet Sheldon Rhoades (460Pts.)

0

Have to unlock doors before 3x lock will work.

2011 Silverado(standard key). Using EVO-GMT4. After truck sits for awhile, will have to unlock, lock, then do 3x lock for it to remote start instead of just using 3x lock. Everything else works fine. Truck isn't with me at the moment.

Login to reply View 2 answer(s)

26/06/2019

Chevrolet Cam Cross (1070Pts.)

0

Should I connect the lt. blue wire

I’m putting an evo-all in my 2016 Cruze limited with an rf kit. The instructions say units from 2017 to December 2018 need to have the lt. blue wire connected. My unit was manufactured January of 2019. I wasn’t sure if the guide had been updated and therefore didn’t know if I should follow page 6 or page 7 of the guide.

Login to reply View 1 answer(s)

05/01/2020

Chevrolet Lucian Maragnano (200Pts.)

0

Start up takes 5x for OEM remote

For 09' Silverado 1500 I have to hit lock 5x for truck to start with remote start but only 3x to turn off remote start.

Login to reply View 1 answer(s)

02/01/2020

Chevrolet Damion Wint (130Pts.)

0

'13 Cruze, key-to-start, Evo Rs gmt1 installed, used dcryptor, and i went by all the steps, so why doesnt it still work?

Only blue light flash once each time lock button is pressed

Login to reply View 1 answer(s)

22/11/2019

Chevrolet Brian Kells (220Pts.)

0

Locking too many times when starting

I just finished installing the evo all in standalone configuration in my 2018 silverado and it is programed and starting the truck. However i have to hit lock 3 times fairly slowly and it seems like the locks are actuating 6 times. its like the remote locks the doors then the evo locks them which repeats 2 additional times and then it starts. I assume it is a setting im missing as my altima does not do this. I will be installing a long range kit in the near future and would like to correct the problem at that time. Thanks for the help.

Login to reply View 1 answer(s)

13/11/2019

Chevrolet CAREL GRUNDLINGH (200Pts.)

0

Doors will not unlock after remote start

After remote start initiated (using 3 x lock on key fob), the doors are locked. However, when trying to unlock the door with the key fob to get in the car, nothing happens. I have to unlock the door by physically inserting the key and turning. Any settings I need to change? 2013 Chev Equinox

Login to reply View 1 answer(s)

11/11/2019

Chevrolet Todd Stiggins (130Pts.)

0

How do I program the EVO-GMT4 to start my 2009 2500HD Duramax when it's cold until the "wait to start" light goes off?

EVO-GMT4 with T harness in stand alone mode.

Login to reply View 1 answer(s)

04/11/2019

Chevrolet ROBERT TERWILLIGER (130Pts.)

0

2011 chevy 2500hd diesel not starting when cold

Evo all with t harness, works great when warm, it will wait and dash lights come on and then it wont even attempt to crank then turn off try a 2nd attempt and same result. In diesel mode set to 14 mins updated to most recent software.

Login to reply View 1 answer(s)

30/10/2019

Chevrolet Sheldon Rhoades (460Pts.)

0

Have to unlock doors before 3x lock will work.

2011 Silverado(standard key). Using EVO-GMT4. After truck sits for awhile, will have to unlock, lock, then do 3x lock for it to remote start instead of just using 3x lock. Everything else works fine. Truck isn't with me at the moment.

Login to reply View 2 answer(s)

26/09/2019

Chevrolet Zephan Vogtman (130Pts.)

0

OEM remote on Evo one

Will the oem remote work for my 2006 Silverado with a evo one or do I need to get an antenna and remote for it

Login to reply View 1 answer(s)

23/06/2019

Chevrolet Allan Materne (190Pts.)

1

2015 Chevy Colorado does not show any display and does not start after pressing the lock button 3'x.

Followed the videos and instructions, but when I try to start it with the remote, Nothing lights up on the radio display like and it doesn't start at all after 3 to 5 seconds. No OEM remote start, do I need a install a OEM remote start for this to work? EVO-GMT1, programming the Evo-All was easy and is up to date. But still does not remote start. Service #001A06 897593