Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

17/11/2024

 Scion Jon Olofson (240Pts.)

0

2015 Scion xB Evo-One, no transponder

Installing an Evo One for remote start with t-harness Toy1, vehicle has canbus, but is not equipped with a immobilizer system. Installed per guide #92261, but am not hung up on programming/key sense. Obviously I am going to use a different sequence because it will not get to the flashing blue led, there is no immobilizer (verified key has no transponder chip). Is there another quide for 2015 xB with Canbus but no immobilizer?
Login to reply View 1 answer(s)

24/01/2023

 Scion Colin Jones (130Pts.)

0

EVO-ONE + START-2 in 2012 Scion IQ app door locking does not work but unlock does

I have an EVO-ONE with T-Harness and EVO-START-2 RF kit installed. The door lock data is connected from EVO-ONE to vehicle harness. The Android app communicates with the car. Using the app to REMOTE UNLOCK the car works fine and flashes the parking lights The LOCK command from the app flashes the parking lights, but DOES NOT REMOTE LOCK the car. Any ideas?
Login to reply View 1 answer(s)

07/03/2022

 Scion Luis Sanchez2 (950Pts.)

0

Alarm setting off

I installed the EVO ONE without T-Harness and RFK411 on a 2014 Scion XD (with standard key). Sometimes after remore start, when the door is opened the alarm is set off and the remote start is halted. Option D2 was inititially turned off.  I turned it on and though it improved quite a bit, it still happens every now and then.  The system is wired and configured per Guide # 102241.  Any help would be greatly appreciated.

Login to reply View 1 answer(s)

25/01/2022

 Scion JakeDressen (130Pts.)

0

trouble getting a 2016 scion ia to remote start reliably

2016 scion ia remote starting, do i need too wake up the light circuit? used an ar35 as per the instructions. also which firmware should i use with this particular model evo-one, t harness, ar35, with the 62-rw were the parts used, all other functions on the remote work flawlessly
Login to reply View 1 answer(s)

24/12/2018

 Scion Brandon Cleary (1250Pts.)

0

2009 Scion TC no keysense

I'm trying to install a EVO-ONE and RF kit into a Scion tC but there's no keysense so I cannot program the module. Is there something else I can do?
Login to reply View 1 answer(s)

29/11/2018

 Scion Brandon Sanderson (160Pts.)

0

2012 xB Manual Transmission.

I am interested in using the the EVO-ONE + THAR-ONE-TOY1 on my 2012 xB. It is a manual transmission, will I be able to use this setup? If so, does anything need to be done to bypass the clutch depressed switch?
Login to reply View 1 answer(s)

27/01/2017

 Scion James Reissfelder (190Pts.)

1

2016 Scion IA Trunk button not working with revo4.1 remote and evo one

The trunk release button on the Revo4.1 remote does not work at all with the car running or not.

The doors lock and unlock  and remote starting is working  using the revo remote.

A2 trunk release and A10 Trunk trigger  options are on.   Is there some setting or connection that I may be missing?
Login to reply View 1 answer(s)

09/12/2016

 Scion Slawomir Milewski (170Pts.)

1

Evo One it will work for 2014ScionXB? The car has no immobilizer system.

I bought the Evo One and i'm having a problem to get it working. I followed guide# 23001, REV:20160601, wiring done and at programing step 5, when I turn the key towards the "on" position the red LED begins to blink and it does not stop. For I have purchased a used car, and it had come with two keys, with one having a Scion logo on the back and a Toyota logo on the other key. The Scion key does not have any stamp marks, and the Toyota key has a H stamp on it. The vehicle I bought was certified by Toyota. To test if my car has a immobilizer I had cut a new key (no chip) in the local hardware store. The new key started the car, while the original keys were in the house twenty feet away. And I googled that only the Canadian xB needed the bypass module. So the question is whether or not the unit will work for the car and how to wire and program it in said vehicle. The firm-ware was installed at the place that I have purchased the Evo One.

Login to reply View 1 answer(s)

04/01/2016

 Scion losmt2 (380Pts.)

0

Start but no crank, 4 times parks light on Evo One

Ok so I finally got my Evo One to respond and actually do something but the remote start is not working. I Have a 2015 Scion FRS with PTS on a manual trans and does the same after leaving it in Ready Mode. I have cut the yellow loop to make it think it's an auto for troubleshooting by the way and the clutch is by passed. I have put a multimeter and it looks like it send power from the starter wire but it very short and it appears to happen when the 2nd ign is turned on (white wire), basically clicks on and then off. The park lights flash 4 times after it fails so based on the guide it indicates no tach signal but I have tried setting 20.2 and 20.5 and 20.1 if I rememeber right. On a side not my service number is 002b03046373 but 002b02046373 shows my info, am I missing something?
Login to reply View 1 answer(s)

31/12/2015

 Scion losmt2 (380Pts.)

0

EVO One and FRS issues

In short my goal is to make the lock x3 work for me but the module is not sending any power from the main 6 pin harness as it should. I have a 2015 Scion FRS with PTS and after a full day I figured out that no matter how many times I try the dcrytor didn't take the immobilizer data as a 2015 FRS. After some self troubleshooting I found out that I can get it to work if I put it down as a 2014 or 2015 Subaru BRZ with PTS. After going through all the steps and putting the EVO One back in the car it turns the yellow LED when in the ignition but does not do anything when trying to use the valet button, no horn no park lights and yes they are wired correctly and check with a multimeter to ensure the module is getting the signals. The blue LED does blink when I press the press the lock and unlock from my factory FOB but more strangely the factory alarm doesn't work anymore, if I click lock button on the FOB and manually open the door the alarm doesn't go off, it does nothing. The car does turn on fine apart of now having the airbag light on. This is driving me crazy and tech support hasn't been able to help much, they say "there's no reason it shouldn't work" I have double and tripled check the wiring and all connections are on the factory wires directly and securely. I can't find any info on this module being used on a BRZ or FRS so I'm starting to question the true compatibility or is there something wrong with this particular module. The AX-One is the same as the EVO One right?
Login to reply View 1 answer(s)

29/12/2015

 Scion losmt2 (380Pts.)

0

2015 Scion FRS (manual) push to start not programming

I go through all the steps and but but when I connect the EVO ONE the second time to read the sample of the immobilizer I get:

The module was not able to sample the vehicles immobilizer data.

I have tried multiple times and sometimes after I start the car the red light doesn't blink and sometimes the red light blinks while the blue led is steady on then the blue led flashes then the red and yellow alternate. This makes it take longer but I have had it go through the regular steps and still the Dcryptor part is not getting my car's data.
 

 

 

Login to reply View 2 answer(s)

29/12/2015

 Scion losmt2 (380Pts.)

0

2015 Scion FRS (manual) push to start not programming

I go through all the steps and but but when I connect the EVO ONE the second time to read the sample of the immobilizer I get:

The module was not able to sample the vehicles immobilizer data.

I have tried multiple times and sometimes after I start the car the red light doesn't blink and sometimes the red light blinks while the blue led is steady on then the blue led flashes then the red and yellow alternate. This makes it take longer but I have had it go through the regular steps and still the Dcryptor part is not getting my car's data.
 

 

 

Login to reply View 2 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue