Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

Vehicle is a 2005 Buick Rainier with standard key. Installed the EVO ONE (remote start firmware 0.44) and the OL-RF-52-SST about a year ago (May 2020). Everything worked OK. The truck had an engine failure and was in the shop for several months with the battery disconnected. When powered back up, the Omega RF remotes no longer work. OEM remotes work. I followed the directions for remote programming as listed below. My antenna LED is not lighting up at all.

The unit was intalled with a custom T-harness for power using OEM connectors and automotive-grade wire. The 30A inline fuse is good.The harness to the antenna looks OK. I verified the unit still has FW 0.44 via my Flash-Link 4 programmer.

Here's the process I tried to program the remotes:

Flash 0.44 into the remote starter and do the following to program:

- ign on off on, led on antenna will light up solid. 

- 4x on brake pedal. It should blink once with each brake press.

- Then send lock from each remote, should blink once again to confirm it programmed.

UPDATE- Apparently a module has failed on the truck, so this appears to be unrelated to the EVO install. Closing the post.

2005 Rainier, EVO One. Wired per diagram. Module had FW 70.18, flashed to 70.39 since I'm using an RF kit OL-RF-52-SST.

Followed vehicle-specific programming per guide 23261 rev 20190514:

1) Hold program button, plug in power connector.

2) Wait for solid blue LED, release button. Blue LED remains on.

3) Plug in 20-pin harness and RF antenna harness

4) Key on, blue LED out, no red LED. No LED at all.

Read & followed this post for the same year Chevy truck:

2005 Alavanche can’t get the red led to come on during programming

Reset per the linked post in the above post:

1) Flashed v. 0.99

2) Disconnected from flasher, connected power plug (Red/Yellow/Blue LEDS on solid)

3) Disconnected main plug.

4) Reflashed to 70.18

5) Setting protection is not on

6) Reset by following above-

7) Hold programming button

8) Plug in power connector, wait for solid blue LED, release button

9) Blue LED off, red LED on then off, yellow LED on solid. This is where the red LED is suppsed to flash.