Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question

0

2017 Civic EVO-ONE/T-Harness with siren

I have an EVO-ONE installed in a 2017 Civic LX coupe, conventional key, manual trans, with T-harness (THAR-ONE-HON2 12-B1). The remote-start/bypass/alarm all work properly. It's my understanding the brown wire on the T-harness (the one with the fuse) from the ignition harness can be used for a siren. What settings do I need to enable to make this work? Right now, when the siren is connected and I crank the car the siren goes off continuously. Thanks, Jeff

0

2017 Civic EVO-ONE/T-Harness with siren

I have an EVO-ONE installed in a 2017 Civic LX coupe, conventional key, manual trans, with T-harness (THAR-ONE-HON2 12-B1). The remote-start/bypass/alarm all work properly. It's my understanding the brown wire on the T-harness (the one with the fuse) from the ignition harness can be used for a siren. What settings do I need to enable to make this work? Right now, when the siren is connected and I crank the car the siren goes off continuously. Thanks, Jeff

0

Which plug is which on clutch pedal and wire colors

I am installing an evo one on a 2011 Mazdaspeed 3 Manual. The instructions for this model are not clear at the clutch pedal. There is a front and rear switch. It isn’t clear which one is which in the directions or the colors that need to be tapped on each switch. Can you verify what signals I should have on these 3 wires going to the respective pins on the module

19/11/2019

Mazda John S (240Pts.)

2

2018 Mazda3 install for a manual (6spd)

So it says it will work for a 2018 Mazda 3 Push Start with a MANUAL transmission. If so, how? I'm familiar with componets and T-harness - This would be my 3rd... Is there a clutch bypass? Does the trans need to be in neutral, if not I assume it wouldn't start - or it would attempt while in gear? Has anyone else installed on this make/model = gotchyas or problems ?? Has anyone installed on a manual trans = extra steps or worth it (juice worth the squeeze) ?? I've installed on automatics ('15 Town & Country and 10 Caravan) - si I get the over all process with the Harnesses and EVO modules. TY!!!

0

2012 Honda Fit Manual Trans Clutch-Bypass Evo-One with Thar-One-HON1 T-harness

Have installed Evo-One with T-harness into 2012 Honda Fit Sport w/ Manual Transmission.  Unit programs correctly, but guide 62321 only gives instructions for Automatic Transmission.  When attempting to remote start, it will only work with the Clutch (manually) depressed. 

Which wire from the Evo-One can I safely use to tap into the clutch interlock switch at the pedal?  Switch has +12v on orange wire during starter activation.

https://photos.app.goo.gl/AjEW7i8N2kWf1Gp59

0

Where is the clutch bypass for 2017 Jetta Standard key

The guide says BCM B pin 51, but I have no wire there

0

clutch bypass for 2017 jeep compass push to start

looking for wiring/diagram for clutch bypass for jeep compass 2017 push to start

0

14 jeep wrangler jk manual

What do I need to install on a 14 jk manual? can I use a t-harness? which one? how do I program it to reserve mode ?

0

2017 cruze stick shift

directions say automatic only. is there an output on evo all i can connect to clutch signal to make it work? trying to avoid using a seperate remote start module. i read on others they have been using dk blue - A8 with 180 ohm resistor in series to clutch signal. but in my diagram that shows a8 as "IN".

0

2014 Jeep JK Clutch bypass

installing a push to start system with my 2014 jeep wrangler JK. I have managed to prove everything programmed well and was usable while the clutch was pushed in. The moment i released the clutch, my EVO-All displayed a RED LED and i had to reprogram for it to work. I suspect this is due to a clutch switch bypass that is required Here are my questions - I see a 5 pin relay that needs to be used but i also see a note that i can use the EVO-ALL relay? - I'm also reading this relay will not allow cruise control. Is this true? If so, is there a way to bypass momentarily but keep the fortin programmed when bypass is not engaged? I would like to install a switch to disable the clutch bypass when the vehicle is being serviced or for use with cruise control. Please help

0

2012 buick regal gs push to start 6spd manual clutch bypass help

Evo-all or evo-one 2012 regal clutch bypass wiring help

0

2014 GTI clutch bypass wire

I have hooked up evo one and all is working if I hold in the clutch in for remote start


the wire A8  in guide 28891 ( GTI 2014, standard key, 6 speed) is not working and i do have the diode in place

i also tried the bcm tan plug wire location 30 and that did not work

also tried pin location 17 tan plug bcm black red , did not work

The answer I got before did not work 

need a little help still

thanks

04/11/2013

Nissan elsam (200Pts.)

0

Clutch Nissan Versa Note 2014 manuel

je chercher a mettre ma clutch sur un nissan versa note 2014 cle reguliere elle est en negatif quel file je doit prendre sur le demarreur fortin?

1

2013 Elantra /w clutch bypass

Do you need to power the starter wire when the clutch is positive trigger?

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer