English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Questions & Réponses

Consultez les questions les plus fréquemment posées et trouvez des réponses pratiques et pertinentes.

recent questions tagged: ...

Réinitialiser
Réduire tout
Tout développer
Réinitialiser
Réduire tout
Tout développer
picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez-nous une question
LES + RECENTS A VOIR! LES + NOTÉÉS LES + RÉPONDUES LES + VUES

31/03/2021

 Chrysler Muqdad Altaee (130Pts.)

0

I can’t program chrt4 all light plinking

I try to program the evo but when pres the the key and connected the 4 pin all the lights are plinking and not convert to sold blue I repeated many times and re connect all the wire again
Connectez-vous pour répondre Voir 1 réponse(s)

31/01/2021

 Dodge Stephen Detmar (130Pts.)

0

2009 Dodge ram, I looked at the guides and install going by them but all i get is all 3 leds flash

Please help frustrated
Connectez-vous pour répondre Voir 1 réponse(s)

05/08/2020

 Ram Kuya Nads (160Pts.)

1

All LEDs are blinking rather than alternating?

2012 Ram 1500 standard key. after installation and wiring ready for programming, i plugged the data connector I just had all LEDs blinking. the first unit was replaced and i have the 2nd now but still the same, is there a problem on the unit itself or just my vehicle?
Connectez-vous pour répondre Voir 1 réponse(s)

26/01/2020

 Ram Greg Brown (140Pts.)

1

all 3 leds continue to flash when data linc harness plugged in cant program

once installe on a 2017 ram 1500 tip key all 3 led continue to flash cant program
Connectez-vous pour répondre Voir 1 réponse(s)

18/12/2018

 Nissan Justin Nail (130Pts.)

0

I've installed my evo-nist1 per install guide #74301 and no start.

3X lock and the evo goest through a cycle, parking lights illuminate, brake lights illuminate, but no start. The more I attempt to research the issue the more diagrams I see with different wiring diagrams. Evo also flashes red three times upon completion of cycle. I have exhausted all options I could come up with on my own to resolve the issue, to no avail. Please help! 2015 Nissan Sentra SV push to start
Connectez-vous pour répondre Voir 1 réponse(s)

03/12/2018

 Dodge Matvey Adz (200Pts.)

2

2015 Dodge RAM 1500 diesel won't start (all LEDs flash 25 times)

Hi, I tried multiple times to get the EVO-ALL module programmed / key decrypted, and after each attempt, after plugging in the module causes all 3 LEDs to flash 25 times, and the module does not respond to the key fob. I am using this installation manual: http://cdn02.fortin.ca/download/29301/evo-all_ig_thr_bi_chr6-ram_2013_key_e_29301.pdf Verified all connections multiple times. Please advise what can be done to fix this. Thank you!
Connectez-vous pour répondre Voir 1 réponse(s)

24/10/2016

 FAQ derek g (342790Pts.)

0

Ever wonder what the led's on the evo mean?

A simple and quick explanation!

Connectez-vous pour répondre Voir 0 réponse(s)

24/02/2016

 Ford Bob jones (260Pts.)

0

Blue led's flash 3x when remote pushed but no start,could the dycripter be wrong?

Blue led's flash 3x when remote pushed 3x but no start,could the dycripter be wrong? Also if I reflash the Bypass side to a different version do I need to run the dycripter again?
Connectez-vous pour répondre Voir 1 réponse(s)

24/02/2016

 Ford Bob jones (260Pts.)

0

Blue led's flash 3x when remote pushed but no start,could the dycripter be wrong?

Blue led's flash 3x when remote pushed 3x but no start,could the dycripter be wrong? Also if I reflash the Bypass side to a different version do I need to run the dycripter again?
Connectez-vous pour répondre Voir 1 réponse(s)

13/12/2013

 FAQ albert (270Pts.)

2

LED color description?

I apparently programmed evo all succescully... Flshing lue led and all. Now whe i click the lock the blue led blinks as i do it. Then nothing happens. I use the key to start the car and yellow comes on and stay on till the car is off. Is this ok. What it means? Thanks .
Connectez-vous pour répondre Voir 1 réponse(s)

11/12/2015

 FAQ RICHARD JACKSON (190Pts.)

2

When plugging the data-link connector to the EVO-ALL all three LED's flash 25 times

When connecting the Data Link cable from the remote start to the EVO-ALL all three LEDs flash 25 times.

While debugging a door lock problem on a 2013 Subaru Crosstrek I did a master reset on the EVO-ALL, set the C1 option as directed and when connecting the EVO-ALL data link cable all three LEDs began flashing.

This is the second unit that this has happened with the same exact scenario. The first unit also had a bad data link connector causing intermittent power but after receiving the new unit and installing with the same lock problem I reset it and experienced the same exact problem.

Re-Flashing the unit with any version of firmware has no effect. Same problem. Both units communicated with the Flash programmer without any problems only when connected to the remote start do I see the problem.

I would have thought it was the cable but... The new unit worked perfectly with the same cable until I reset the unit.

Help please.

 

------update 12/14/15

Two things. When I say three LEDs are flashing I mean all 3 are flashing at the same time not sequentially. On the first unit I tried reprogramming the key but this was not successful but I don't remember the exact problem. 

After reset and connecting with the Flashlink2 I can see that the key bypass is still there and active. Are you saying that I need to run the decrypter programming sequence again?

At the moment the Evo-All will not talk to the compustar at all except to pass signals through. 

Thank you

Connectez-vous pour répondre Voir 2 réponse(s)

11/12/2015

 FAQ RICHARD JACKSON (190Pts.)

2

When plugging the data-link connector to the EVO-ALL all three LED's flash 25 times

When connecting the Data Link cable from the remote start to the EVO-ALL all three LEDs flash 25 times.

While debugging a door lock problem on a 2013 Subaru Crosstrek I did a master reset on the EVO-ALL, set the C1 option as directed and when connecting the EVO-ALL data link cable all three LEDs began flashing.

This is the second unit that this has happened with the same exact scenario. The first unit also had a bad data link connector causing intermittent power but after receiving the new unit and installing with the same lock problem I reset it and experienced the same exact problem.

Re-Flashing the unit with any version of firmware has no effect. Same problem. Both units communicated with the Flash programmer without any problems only when connected to the remote start do I see the problem.

I would have thought it was the cable but... The new unit worked perfectly with the same cable until I reset the unit.

Help please.

 

------update 12/14/15

Two things. When I say three LEDs are flashing I mean all 3 are flashing at the same time not sequentially. On the first unit I tried reprogramming the key but this was not successful but I don't remember the exact problem. 

After reset and connecting with the Flashlink2 I can see that the key bypass is still there and active. Are you saying that I need to run the decrypter programming sequence again?

At the moment the Evo-All will not talk to the compustar at all except to pass signals through. 

Thank you

Connectez-vous pour répondre Voir 2 réponse(s)

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer