Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Natalie Maldonado

Joined on the:

Nov. 7, 2019

Score

880

Comment(s)

21

Voted question(s)

0

Voted answer(s)

6

Votes up

0

Votes down

6

Votes up received

1

Votes down received

0

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

17/12/2021

Jeep rey g (300Pts.)

0

i need wiring diagram for 2017 jeep wrangler manual transmission?

hi there,,,i need wiring diagram for 2017 jeep wrangler manual tranny,,and can i use only evo all?thanks..

0

MT remote start, why not available? Any way to use a relay like with the Wrangler?

0

2009 Toyota Tacoma Evo One Programming successful, but wont start

After successful programming, we couldn't figure what exactly is wrong. Continuity was checked on every single wire configuration and all tested properly wired. Hood pin, lock/unlock/lock Unit S/N 002B04 107018 Is there anything else needed that we are missing? Thanks in advance

0

Remote start standard key 2019 Honda civic not working

Evo One remote start T harness 2019 Honda civic standard key not working I followed the guide and I have the parking light and horn connected. I also have the fuse connected to the odb contact +. After doing the sequence and yellow and red alternate flashing, I disconnected the unit to use the decryptor and transferred the data. Everything seems ok and once I connected everything back, there is no blue light or any light on the Evo. I lock the car and after some seconds tried 3x lock, nothing happens, the Evo doesn't show any light at a!!. No remote start. When I turn the ignition on, the yellow light on the Evo is on (no flashing). Nothing else happens. Is there any other step needed that I am missing? Evo id: 002B04 107292 By the way, the firmware installed is the latest available Thanks in advance

0

P0830 code came up after weeks of nstallation (EVO ONE with manual transmission bypass 2017 Wrangler)

After installation of 5 pin relay and successful remote start, the check engine light came up randomly....so far two times. What can be wrong?

0

LINKR-LT2 not updating status door locked after ready mode

I finally got my EVO-ONE and the LINKR-LT2 to remote start my 2017 Jeep Wrangler manual transmission... it works every time.. 

The only thing that technical support from mycar controls and myself haven't figure it out yet is "why after ready mode (neutral position, parking brake, brakes) the EVO-One will let me remove the key and unlock the doors or door depending of the initial command which I love (It does follow 1 passenger or more than one and unlocks the necessary door or doors depending on the remote sequence done to unlock driver's door or all doors)...back to the commandas... after I shut the door the car will kill the engine and after some seconds...I think is like 60sec. the car will lock the doors by itself.

Every time the car locks the doors...mycar control app will not show this status and only will have the green signal with doors unlocked,.. even though they are in fact locked.

Mycar control technical support told me that I have to choose an option to lock the doors with my factory remote and eliminate the automatic lock the doors command from the EVO-ONE or CAR ALARM (we are not sure who is sending the command... I think is the EVO-ONE but I need to confirm the blue led to be sure and haven't done it yet)

Can someone help me to know what setting number will set this option?,,,, The evo-one is super hidden and in order to remove it and have space to work under my steering column I have to remove the driver seat... jeep space in the front is super tight...

Thanks in advance 

Natalie  

Any help?

0

Manual transmission ready remote start

I have a 2017 Wrangler and after completing the hood pin switch and the installation of the siren, I finally tried to test the remote start methord

Using the factory keyless remote lock-unlock-lock....after several seconds...nothing happened 

Using the LINKR-LT2 mycar control app after several seconds from blue turned into red and nothing happened. 

I am assuming my reqdy mode procedure will be to have the engine running,  transmission in neutral,  pressing the brake, engaging the parking brake, release the brake pedal, turn the engine off then open the door and leave setting the alarm to lock the car.... but the engine shut off as soon as I remove the key from the ignition.

 

What am I doing wrong?

S/N 002B04043387

 

0

2017 Jeep Wrangler real parking light wire color. ?

I followed the lead to look under the driver's seat and check the white/purple(found it) wire necessary for the evo one but at the tail light pigtail it looks like this wire is missing. The only wire that comes hot when the lights are on, is the orange/white wire at the tail light pigtail. Any advice?

0

Are the parking lights connection necessary for remote start in both instances? Mycar LINKR-LT2 will not remote start

Parking lights purple/white not located on driver kick panel

0

generic evo all guide

Any one have a link to a generic evo all guide? Non vehicle specific. The old chrt5 guide I think was pretty generic. Any have a link?

0

Flashlink setup 2017 Jeep Wrangler Manual Transmission T harness

I purchased my Evo One prep with linkr from seller and adding a siren option I noticed this settings for remote start: 14 ALARM ON/OFF STARTER ON/OFF selected 14.1 (Alarm disabled. Remote starter enable) instead 14.2 31 SPECIAL APPLICATION PROGRAMMABLE OUTPUT (+) selected (Disable) instead 31.4 Is there any way to know if these settings are correct? Thanks Natalie

1

Connection of 4 sensor triggers to Evo One Jeep Wrangler manual transmission?

How many ports are available to conect more than one trigger sensor? The installation sheet doesn't have the different pigtail ports name or function. H, I,? Can the Evo One control all 4 sensors: shock, tilt, glass broken, motion. How can the hood switch can be used to trigger the alarm since the regular jeep does not have security while armed to protect battery or any bluetooth relay accessory in the engine compartment. I just ordered the Evo One and the seller wired everything including the linker so the wiring was prep prior to delivery of the components. I am trying to add all these sensors to the unit. Thanks for helping Natalie

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue