Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Evo one won’t remote start but will let the car continue to run after starting the car manually..

2017 Subaru WRX. Won't Remote start. Manual Trans. The yellow wire on the main harness (T-Harness) that goes to the clutch wire does nothing when trying to remote start. But the car will continue to run after I turn the key off.

0

OBDII Port not connecting after install

I have a working Fortin Evo-One installed on a 2018 Subaru Crosstrek. The unit has worked flawlessly for over a week. Today I had a check engine light appear and I cannot connect to the ECU via my OBD tool. I tried the tool on a different vehicle and it works fine. Does something need to be done in order for the OBD port to work correctly? Thanks

0

No tach detected??

I have a 2017 Subaru Legacy 2.5l automatic (standard key) with evo-one for years now with no issues till today I installed the Autolink device,when remote starting vehicle, it starts for a few seconds but shuts off and 4 parking light flashes which is no tach detected?please help.. thanks service # 002B02xxxxxx

0

2014 Subaru Impreza Basic ,EVO ONE NOT WORK

Evo One + Subaru Impreza 2014 Basic Im tired installing evo one for this car ,all connection is ok regular installation but still no illumination blue light when lock/unlock.Program procedure is ok ,decryptor ok and still no work blue led.

0

2014 Subaru Impreza Basic ,EVO ONE NOT WORK

Evo One + Subaru Impreza 2014 Basic Im tired installing evo one for this car ,all connection is ok regular installation but still no illumination blue light when lock/unlock.Program procedure is ok ,decryptor ok and still no work blue led.

0

Remote start not working

service number: 002307 237674 checked all wires to diagram and connections all are good. please help!!

0

Programming features on evo one

 


Question : so is there any way to remote shut off car after remote start is on?

at the moment the only way to shut it down is with the brake switch..

 

 Q: Also the heated seats work with remote start, can the rear defrost work as well ?  and if so how do i get defrost  to work?

Q: when i change options in the unit with the flash link do i need to on the internet or can i just hook into the unit at the car with the computer and flash link and click on the options i want and hit save?

Again You Guys are Wonderful.

Great product as well

Thanks

0

2013 wrx removed evo one, climate control and clock are no longer work, related?

Hi, I have a 2013 WRX US model. I removed my Evo one the other day since I am prepping to sell my car. I disconnected the wires from d1 and d3 and connected them together to get my door loocks to work again. Now my climate control or upper clock display do not work. I checked every single fuse on the car and nothing. Is this tied to something else during the install? I put the fortin back together and still no go. Not sure if it is but was just wondering. thank you

0

Fortin Evo One red and yellow flashing

I have a evo one and using a t-harness for my 2015 Subaru WRX Limited Manual transmission. I go the wires all hooked and Im not sure if I was able to get the initial programing done correctly. I was doing this at work and needed to get home despite being unsure of it being programed properly, started my car and drove home. I tried doing the initial setup with the red and blue light being solid. Now the module has a solid blue while blinking red and yellow at the same time. Is this a concern ? What should I do if it's not correctly setup.

0

Fortin Evo One red and yellow flashing

I have a evo one and using a t-harness for my 2015 Subaru WRX Limited Manual transmission. I go the wires all hooked and Im not sure if I was able to get the initial programing done correctly. I was doing this at work and needed to get home despite being unsure of it being programed properly, started my car and drove home. I tried doing the initial setup with the red and blue light being solid. Now the module has a solid blue while blinking red and yellow at the same time. Is this a concern ? What should I do if it's not correctly setup.

1

fortin evo one will not go into function mode to program remotes

2010 subaru outback. everything else programs nice in the flashlink manager with the key decryption and remote start program and flash. when i turn the key on and hold down the valet button the red light never flashes, if i just press it the times it goes into valet mode and the light turns on then and comes back out so i know its not the button itself. i have done a master reset by pressing button on the unit till its red then again till all the lights flash. and i have also done a master reset with the flashlink and completely reprogram the unit.

1

fortin evo one will not go into function mode to program remotes

2010 subaru outback. everything else programs nice in the flashlink manager with the key decryption and remote start program and flash. when i turn the key on and hold down the valet button the red light never flashes, if i just press it the times it goes into valet mode and the light turns on then and comes back out so i know its not the button itself. i have done a master reset by pressing button on the unit till its red then again till all the lights flash. and i have also done a master reset with the flashlink and completely reprogram the unit.