Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

1

Remote start of the 2023 Outlander

The start-stop button is given a minus twice, with an interval of 3-4 seconds. We have to move the instrument panel frame to get to the button connector. There was a whitish line. I fitted a 12-ring loop to the rear cylinder of the start-stop button. I removed the battery from the key and attached a 2 cm diameter 12-ring loop to the logo. I cut the gray wire on the brake connector with the relay contacts and gave a plus to the light blue wire. To turn off the engine, it takes 3-4 seconds to give a minus to the start-stop button, and then a minus impulse to the door button... Behind the kick panel there was a light blue wire. The door lock-unlock lines were also there...purple and beige.

0

2023 OUTLANDER

Hello. 2023 Outlander (Euro) does not have a standard remote start. Is there another option for remote start?

0

2018 RVR LED & headights light Flash continusuly after Remote Started

Hello everyone We installed an Evo-One on this RVR 2018 with factory HID headlights and LED Fog light using 23101 guide. We followed the guide to a T, the issue we are have is that as you remote start the vehicle using 3X lock the vehicle starts properly, but if the lights are set on automatic, the headlights and LED lights flash continuously as well if you turn off the lights and remote started the Vehicle the LED fog lights flash continuously both will flash until you take over the vehicle. Has anybody come across this? We think it might be a faulty EVO one module any thoughts please help.

0

shut off when I press the brake

I am writing to report an issue with my car’s remote start and shutdown process. When I press the lock button on the car key three times, the car starts remotely, as expected. However, after entering the car by pressing the unlock button, I encounter a problem: when I press the ‘Press to Start’ button twice in succession and then press the brake, the engine shuts off immediately, and the message ‘Wegfahrsperre’ appears. Could you please help me understand and resolve this issue?” FORTIN EVO-ONE-MIT2 EVO-ONE + T-KABELBAUM Mitsubishi Outlander 2016 SN:002B04 291538 On the first press, the blue light blinks. On the second press, the blue light also blinks. On the third press, the blue light blinks, followed by the red and yellow lights. The blue light then turns off, leaving only the red and yellow lights on. My issue is that I want the engine to keep running so I can drive immediately, rather than having the engine shut off when I press the brake pedal and then needing to restart it to get going.

0

when i activate the remote start it flashes blue 5 times.

i just bought a mitsubishi lancer and it has the fortin ftx84 remote start put into it, when i activate the command start it flashes blue 5 times, i have read that this is the hood latch. how can i fix or figure out what the issue is with the hood latch?

0

wegfahrsperre evo one

Everything works fine There's one problem. When I want to drive the car press the push button ×2 but start the engine shuts off A message appears wegfahrsperre

0

I press the lock button three times but the car does not start remotely

Hello. Evo one is connected By HARNESS FOR MITSUBISHI VEHICULES. Evo One has been updated. Everything was done right. But the car does not start remotely When press the lock button 3 times!!

0

PUSH TO START SAMRT KEY

Hello Does anyone know how to test the starter wire on the ECM plug of a 2017 Mirage? Does it have 12V and drops on crank like on a standard key, or is it different.

0

Mirage Evo-all

Can i remote start a 2017 Mirage with Evo-all and the OEM key fob or do i need to install anything else? And if i need what do i need to install. Thank you

0

mitsubishi outlander 2020 pushstar

my modulo se programa muy bien el problema que tengo esque no reconose las can 1 hight y low no veo datos de imobilizador ..ise otras pruebasde salida de voltage como ignicion y star.y estan bien ay salida de voltage per el inmobilizador no manda la señal de bypas al inmo del carro..lo e echo muchas veces el procedimiento que ast me bloquearon el poder hacer el decryptor dice que mucho lo e intentado me gustaria me dieran el soporte tecnico para mi vehiculo ya le cambie 3 tipos de firware y lo e reiniciado y nada..numero de by pass sn-001a07 226844

0

immobilizer system service required error after RFK kit install - car will no longer start with original key

Remote start was programmed and worked perfectly, however the takeover sequence only worked by pressing brake and restarting the car with original key. I just installed the RFK912 and progammed it corectly, the car worked fine starting from the rf remote and original remote. The car both remote started and then after shutting down started normally with the original fast key. The same night, after starting with the RF key and shutting down pressing the break, the car no longer starts with the original key and shows the immobilzer system service required fault. I can still remote start the car but cant use the original remote to start and drive away. after removing the evo-all - the car shows the same fault. It is stuck where it is. i tried to use teh dcrypot but it needs resetting - i want to reflash the dcryptor and try starting again. SN 001A07140493 the car is MITSUBISHI OUTLANDER 2014 EURO

0

evo-one stand alone installation

I installed the Evo-One (standalone) on the outlander sport today. Was it necessary to flash and bypass and remote start, or is it just the remote start?

0

2020 Mitsubishi Outlander

I am trying to wire the canbus connections and according to the diagram there on the connection that is being tapped for Can2 high has a yellow/pink wire in the connector and Can2 low is a red/white wire on that same connector. This year must have changed since the wire in the harnass is blue white/wire in in its location of the yellow/pink wire. Can anyone give any insite on what wire i should be connecting this to? I tried the blue white wire and that doesnt work. My unit doesnt flash as it should to use the decryptor plus the vehicle then kicks off all sorts of errors! All the wire colors match up except for this one. The unit I am using is the EVO-ONE. Thanks, John