Questions & Answers

“I am writing to report an issue with my car’s remote start and shutdown process. When I press the lock button on the car key three times, the car starts remotely, as expected. However, after entering the car by pressing the unlock button, I encounter a problem: when I press the ‘Press to Start’ button twice in succession and then press the brake, the engine shuts off immediately, and the message ‘Wegfahrsperre’ appears. Could you please help me understand and resolve this issue?”

FORTIN EVO-ONE-MIT2 EVO-ONE + T-KABELBAUM

Mitsubishi Outlander 2016 

Hello, 

When pressing the remote start button on the RFK942 key fob, the remote start does not always activate. When this does not happen, the car behaves differently: the marker lights come on along with the low beam headlights for a couple of seconds, then everything goes off. However, when the remote start command is successful, the low beams do not activate, the turn signals come on for half a second, followed by the marker lights. Additionally, there seems to be a door lock click, then the engine starts, which can be seen in the video. https://youtube.com/shorts/B6o0cWfPQQo

Remote start with the factory key, activated by three presses on the lock button, does not cause any issues with the remote start.

The flash-link 4 has version 5 firmware, vr. 4.08. An additional impact sensor and siren are installed.

There is also an issue where if the car is armed or started with remote start, if the trunk door is opened with a sweeping motion from below (via the sensor), the siren starts making noise. If opened with the button on the door, everything is okay.

Thank you for your help!

This is driving me crazy... It works and then it does not... Need some help please.

Everything is connected per instructions (Guide # 24871), except; I had to disconnect the (A8 dk. blue) to Driver Door pin, as it left the Door ajar on constantly. 

The Yellow loop has been cut on the fortin unit.

Fortin unit SN: 002B04 251304

Crank no start and 3 parking light flashes. 

 Setup in Flash link:

Bypass

Firmware 86.05

Hardware inside 4.0

A1 on

A2 off

A3 on

A4 on

A5 on

A6 on

A7 on

A8 off

A9 on

A10 off

A11 on

B1 on

C1 on

D2 on

D3 off

D4 off

D5 on

D6 off

E4 off

E5 off

Remote start

Firmware 1.26

Hardware inside 7.0

2 off

3 1

4.1

6.1

7.1

8.1

9.1

10.1

11.1

11.4

12.1

13.2

14.1

15.1

16.5

18.1

19.1

20.8

21.1

24.1

25.6

26.1

29.1

30.1

31.4

32.5

33.1

35.2

36.2

37.1

38.1

39.2

This is driving me crazy... It works and then it does not... Need some help please.

Everything is connected per instructions (Guide # 24871), except; I had to disconnect the (A8 dk. blue) to Driver Door pin, as it left the Door ajar on constantly. 

The Yellow loop has been cut on the fortin unit.

Fortin unit SN: 002B04 251304

Crank no start and 3 parking light flashes. 

 Setup in Flash link:

Bypass

Firmware 86.05

Hardware inside 4.0

A1 on

A2 off

A3 on

A4 on

A5 on

A6 on

A7 on

A8 off

A9 on

A10 off

A11 on

B1 on

C1 on

D2 on

D3 off

D4 off

D5 on

D6 off

E4 off

E5 off

Remote start

Firmware 1.26

Hardware inside 7.0

2 off

3 1

4.1

6.1

7.1

8.1

9.1

10.1

11.1

11.4

12.1

13.2

14.1

15.1

16.5

18.1

19.1

20.8

21.1

24.1

25.6

26.1

29.1

30.1

31.4

32.5

33.1

35.2

36.2

37.1

38.1

39.2

HI

can you please reset flash limit on evo can SN: 002204 033446

thanks!

Reposting because, well, the first thread will never been seen again and the answer missed important points

Please read the whole thing.

Eclipse Cross, 2018, SE

Latest firmware for starter and bypass. Loaded recommended options and confirmed the options specified in the setup PDF for the car were set. Using the MITS2 harness.

3x lock works for remote start works.

Tried various (3?) methods of syncing, all of which seemed to work, however, device still only shows it's own information (battery voltage, GPS, and "connected" icon)

Yes, using the crossover cable. Yes using the right port on the evo-one (blue).  

Tried sending the unlock command/lock command at the last steps of the sync. Door open and door closed. Didn't seem to matter. 

Tried switching the protocol in the app to something else then back to Fortin.

Confirmed the "datalink" protocol is Fortin 2  

Previously, this carlink was used with an evo-all for a different car and it worked great. Now it does not.