Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2018 RVR LED & headights light Flash continusuly after Remote Started

Hello everyone We installed an Evo-One on this RVR 2018 with factory HID headlights and LED Fog light using 23101 guide. We followed the guide to a T, the issue we are have is that as you remote start the vehicle using 3X lock the vehicle starts properly, but if the lights are set on automatic, the headlights and LED lights flash continuously as well if you turn off the lights and remote started the Vehicle the LED fog lights flash continuously both will flash until you take over the vehicle. Has anybody come across this? We think it might be a faulty EVO one module any thoughts please help.

0

shut off when I press the brake

I am writing to report an issue with my car’s remote start and shutdown process. When I press the lock button on the car key three times, the car starts remotely, as expected. However, after entering the car by pressing the unlock button, I encounter a problem: when I press the ‘Press to Start’ button twice in succession and then press the brake, the engine shuts off immediately, and the message ‘Wegfahrsperre’ appears. Could you please help me understand and resolve this issue?” FORTIN EVO-ONE-MIT2 EVO-ONE + T-KABELBAUM Mitsubishi Outlander 2016 SN:002B04 291538 On the first press, the blue light blinks. On the second press, the blue light also blinks. On the third press, the blue light blinks, followed by the red and yellow lights. The blue light then turns off, leaving only the red and yellow lights on. My issue is that I want the engine to keep running so I can drive immediately, rather than having the engine shut off when I press the brake pedal and then needing to restart it to get going.

0

The car does not start remotely

When I press the car lock button 3 times The car does not start remotely

0

I press the lock button three times but the car does not start remotely

Hello. Evo one is connected By HARNESS FOR MITSUBISHI VEHICULES. Evo One has been updated. Everything was done right. But the car does not start remotely When press the lock button 3 times!!

0

2016 outlander

I want to install evo-all on 2016 outlander(PTS...standalone). On the car, the module can not be programmed. After opening the ignition, the blue LED goes out and a lot of errors are written in the devices. The module I reflashed several times (001A07311845). I also tried another module ... Some kind of Japanese autorun PZ 113-04221 was installed on this car earlier P.S. When trying to program, the ignition does not turn off unless we disconnect the CAN connector When I turn on the ignition and wait for the blue LED to start flashing, then it writes errors ... and the ignition does not turn off with the start button if I do not remove the CAN connector from the module. And the blue LED is not visible (when I remove the CAN connector and turn off the ignition, the blue LED lights up ---

0

2011 Mitsubishi Outlander ES (2.4L) KEY TO START - What to buy for remote start

Hello experts, please suggest what to order for remote start on my 2011 Mitsubishi Outlander ES 2.4L key-to-start vehicle. I would want to use the factory remotes key fobs.

0

PARKING LIGHTS NOT COMING ON WHEN THE REMOTE START IS RUNNING

2016 Mitsubichi Outlander Sport Key start, remote start operating with OEM Key after pressing the lock button 3x Remote start installation with T-connectors When pressed 3x, all the parking lights flashing and rhe cars start, then just passenger side still on.

0

PARKING LIGHTS NOT COMING ON WHEN THE REMOTE START IS RUNNING

2016 Mitsubichi Outlander Sport Key start, remote start operating with OEM Key after pressing the lock button 3x Remote start installation with T-connectors When pressed 3x, all the parking lights flashing and rhe cars start, then just passenger side still on.

0

2012 lancer se

Hi there about a year ago I purchased evo-one for my mitusbishi lancer se 2012 it was working fine until i stop using it for 2 months I updated the firmware to the latest. when I tried to reset it and reprogram it the lights flash but the engine doesn't want to turn over. I get a warning that my driver side door is open which its not and the when I hit the button on the key the first time the red lignt next to the reset switch flash raipdly when i hit it the second time it slows down and the third it turns off now on the module itself the three leds first the blue then the red goes soild then the yellow and back to blue flashing I want to know how can I downgrade the firmware for the remote starter and bypass. because I think that what making it not work right Thank you

0

2012 lancer se

Hi there about a year ago I purchased evo-one for my mitusbishi lancer se 2012 it was working fine until i stop using it for 2 months I updated the firmware to the latest. when I tried to reset it and reprogram it the lights flash but the engine doesn't want to turn over. I get a warning that my driver side door is open which its not and the when I hit the button on the key the first time the red lignt next to the reset switch flash raipdly when i hit it the second time it slows down and the third it turns off now on the module itself the three leds first the blue then the red goes soild then the yellow and back to blue flashing I want to know how can I downgrade the firmware for the remote starter and bypass. because I think that what making it not work right Thank you

0

I installed my Evo one in my 2015 Lancer and it won't work

I installed my Evo One with standard key. well i installed it and it wasn't working 100% meaning that some time it would work on the first try and not work until the second try, or even not at all. So i went back and checked and I may have found a loose starter (yellow) wire, but not 100% certain of that. Now Click the fob 3X, all the lights come on (dash, interior, parking) doors unlock, it seems to run its course. same as before but now does not start at all. Parking lights flash 4X indicating no tach. Then it cycles again with the same results but no start. I think the encryptor is now not working or had some issues to start with. with my power probe I have tested that everything else coming from the evo one is working. The ignition wire (pink) + comes on and then the starter wire (yellow) + comes on but the car will not start. I then tested the cars harness by unhooking the evo, then I put the key in the ignition in the on/run position, then use my power probe on the same wire that the yellow wire was plugged into, the car will start. 

So then I'm thinking I should try and run through the install procedure with plugging in the 6 pin and running through the LED flashing light stop on Blue again procedure. This did not help any.  

So, what is the best way to reset everything and try it again, or do you have something else I should check first,

Best Regards

Louis   

 

 

0

2020 Mitsubishi Outlander

I am trying to wire the canbus connections and according to the diagram there on the connection that is being tapped for Can2 high has a yellow/pink wire in the connector and Can2 low is a red/white wire on that same connector. This year must have changed since the wire in the harnass is blue white/wire in in its location of the yellow/pink wire. Can anyone give any insite on what wire i should be connecting this to? I tried the blue white wire and that doesnt work. My unit doesnt flash as it should to use the decryptor plus the vehicle then kicks off all sorts of errors! All the wire colors match up except for this one. The unit I am using is the EVO-ONE. Thanks, John

0

Ready mode wont enable

2015 Mitsubishi Lancer Evolution (manual trans). Using an EVO-ONE, I checked all wires and made sure everything was correct the only thing I didnt connect was the motion sensor, I cannot seem to find it in the driver side footwell unless the plug has been changed in later year models. Anyway when trying to remote start the parking lights flash three times, indicating ready mode is not enabled. I have tried all 3 different ways as described in the installation instructions but still does not work.

17/10/2018