Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

Outlander 2022 with Fortin EVO One - remote start does not always work when using RFK942

Hello, 

When pressing the remote start button on the RFK942 key fob, the remote start does not always activate. When this does not happen, the car behaves differently: the marker lights come on along with the low beam headlights for a couple of seconds, then everything goes off. However, when the remote start command is successful, the low beams do not activate, the turn signals come on for half a second, followed by the marker lights. Additionally, there seems to be a door lock click, then the engine starts, which can be seen in the video. https://youtube.com/shorts/B6o0cWfPQQo

Remote start with the factory key, activated by three presses on the lock button, does not cause any issues with the remote start.

The flash-link 4 has version 5 firmware, vr. 4.08. An additional impact sensor and siren are installed.

There is also an issue where if the car is armed or started with remote start, if the trunk door is opened with a sweeping motion from below (via the sensor), the siren starts making noise. If opened with the button on the door, everything is okay.

Thank you for your help!

0

Evo-One for Mitsubishi Triton (pickup truck)

Hi, I want to buy Evo-One for my Mitsubishi Triton (pickup truck, diesel engine, automatic transmission) manufactured in Thailand, 2020. I used the card in Vietnam. I just want to know if I can use Evo-One Fortin product for my car, is it compatible. If yes, do i need to buy the Thar-One-Mit 2 (T-Harness for Mitsubishi vehicles) to work for connection or installation process with Evo-One. Thanks in advance,

2

Evo one not programing, and can't to connect auto mitsubishi pajero sport 2013 Year diesel

Hello. I will be need your help. I have a car Mitsubishi pajero sport 2013 year with diesel engine. And need used to remote star Evo One. But any conect diagram not working with program bypass system, and i tride any version firmware 74 86 and last 0.99(now light all colour led) for programing module. I seen what use evo all for working with this car, i think what Evo One will be working too. And i used 7 from 8 programing module. With 74 and 86 software i have a problem programing when turn ignution is onn but blue light is power off and all, i cheked connect to can wire connect several times. Please say me information to help, my sn 002b04 265103

0

wegfahrsperre evo one

Everything works fine There's one problem. When I want to drive the car press the push button ×2 but start the engine shuts off A message appears wegfahrsperre

0

The car does not start

I connected the wires yesterday But I did not connect the device because it needs to be updated and the Fortin FLASHLINK4 has not arrived yet. I tried to start the car today but it won't start. ?for the car to start Should the EVO-ONE be connected after connecting the wires

0

evo one flash limit, please reset

0

CL6 / Evo-One - Not Communicating?

 

Reposting because, well, the first thread will never been seen again and the answer missed important points

 

Please read the whole thing.

 

Eclipse Cross, 2018, SE

Latest firmware for starter and bypass. Loaded recommended options and confirmed the options specified in the setup PDF for the car were set. Using the MITS2 harness.

3x lock works for remote start works.

Tried various (3?) methods of syncing, all of which seemed to work, however, device still only shows it's own information (battery voltage, GPS, and "connected" icon)

Yes, using the crossover cable. Yes using the right port on the evo-one (blue).  

Tried sending the unlock command/lock command at the last steps of the sync. Door open and door closed. Didn't seem to matter. 

Tried switching the protocol in the app to something else then back to Fortin.

Confirmed the "datalink" protocol is Fortin 2  

Previously, this carlink was used with an evo-all for a different car and it worked great. Now it does not. 




 

0

ASCL6 / Evo-One - Eclipse Cross 2018 - No unlock/lock/start/etc

Eclipse Cross, 2018, SE Latest firmware for starter and bypass. Loaded recommended options and confirmed the options specified in the setup PDF for the car were set. Using the MITS2 harness. 3x lock work for remote start works. Can't seem to get the Carlink and Evo-One to communicate. Tried various methods of syncing, all of which seemed to work, however, device still only shows it's own information (battery voltage, GPS, and "connected" icon) Using the crossover cable in the CL6 instructions and confirmed correct port on evo-one. Tried the valet switch sync, the on-off-on sync, the unplug, red/blue sync Tried sendin the unlock command/lock command at the last steps of the sync. Tried switching the protocol in the app to something else then back to Fortin. Confirmed the "datalink" protocol is Fortin 2 (there are no other options other than the FMH) I have found a thread or two describing a problem just like this, but those solutions were mostly about not using the correct crossover, having the learn procedure not working as expected, so they weren't relevant to me, sadly. Previously, this carlink was used with an evo-all for a different car and it worked great. Recently resubbed after a year to use in the Cross and have spent the better part of a week trying to figure this one out. Tried all of the procedures in the programming FAQ as well as the workarounds. The procedures, each different type, all seem to work correctly, but the behavior never changes. Evo-one still unresponsive to the carlink. Really wondering at this point if the ascl6 can do anything without splicing more wire / whether it's a bug / or ? At a loss on this one. At the last step of syncing (turning the car off), the red/blue flash 4 times. Can't seem to find a diagnostic for what this means.

0

Door trigger stays open when connecting the 20 pin, remote start works okay.

Hi, Everything works fine with the remote start however, the door ajar light in the dash stays always on. And when I disconnect the 20 pin connector, then the door ajar works fine. I have connected the dk.blue wire to the lt.green wire at the fuse box as instructed. Also I have programmed the 32.5 option. The car has oem alarm. SN 002B04 251304 Any ideas? Thanks

0

12 relay clicks in the engine bay?

Hi, I installed the EVO ONE on my Mitsubishi Eclipse 2012 (standard key). Everything is working, but when interacting with the remote start via the RFK411, there is a rapid 12 or so relay clicks coming from the engine bay. Is this normal? Everything is working, starting the car, lock and unlock doors. Please advise. Thanks

0

2017 mits mirage std key, evo one with rm411 starts then shuts down after 10 seconds

2017 mits mirage, evo one with rm411 starts and shuts down after 10 secs, 2x

0

2012 lancer se

Hi there about a year ago I purchased evo-one for my mitusbishi lancer se 2012 it was working fine until i stop using it for 2 months I updated the firmware to the latest. when I tried to reset it and reprogram it the lights flash but the engine doesn't want to turn over. I get a warning that my driver side door is open which its not and the when I hit the button on the key the first time the red lignt next to the reset switch flash raipdly when i hit it the second time it slows down and the third it turns off now on the module itself the three leds first the blue then the red goes soild then the yellow and back to blue flashing I want to know how can I downgrade the firmware for the remote starter and bypass. because I think that what making it not work right Thank you

0

2012 lancer se

Hi there about a year ago I purchased evo-one for my mitusbishi lancer se 2012 it was working fine until i stop using it for 2 months I updated the firmware to the latest. when I tried to reset it and reprogram it the lights flash but the engine doesn't want to turn over. I get a warning that my driver side door is open which its not and the when I hit the button on the key the first time the red lignt next to the reset switch flash raipdly when i hit it the second time it slows down and the third it turns off now on the module itself the three leds first the blue then the red goes soild then the yellow and back to blue flashing I want to know how can I downgrade the firmware for the remote starter and bypass. because I think that what making it not work right Thank you

13/03/2021