Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question

0

2015 outlander euro

Hello. I also tried the master reset as you told me. I tried another device, which I tried on Ford before (001A07391859), but "take over" is not possible... it says on the monitor that the immobilizer system needs service.

0

2015 outlander take over

Hello. I installed Evo-Al for 2015 Outlander (PTS) Standalone. After remote start-up, we go in the car, I click 2 times on the Start-Stop button and he writes that he does not see the immobilizer (like this), and the engine turns off when pressing the brake.

0

2014 Mitsubishi Outlander Evo-all with evo-start lte and rf642 kit

Hello there guys, i have a 2014 mitsubishi outlander with evo-all and rf442 kit. All works fine and well. And then i added an evo-start lte module. I was able to program it with the rf442 kit. RF kit works fine as before. Then the app for the evo-start works fine as well except for the remote stop/engine off function. Lock, unlock, and remote start/engine on function works. But when i try to do and remote stop/engine off. It doesnt work. Is this a bug on the app? Or is there a programming issue? Again. Lock, unlock, and remote start/engine on works. Its just the remote stop/engine off function that is not working. any help will be appreciated. Thanks in advance. Btw im using it on ios device.

0

PUSH TO START SAMRT KEY

Hello Does anyone know how to test the starter wire on the ECM plug of a 2017 Mirage? Does it have 12V and drops on crank like on a standard key, or is it different.

0

Shuts off with unlock signal and door closed

Worked correctly for a year and a half. Recently it will not start with one flash after sitting for a couple hours. Also, the remote start shuts off with unlock signal and all doors closed, but will start just fine remote started with door open. Went over all power and ground connections, made with butt connectors, moved grounds, no issues found.

1

Outlander 2014 - Remote starts works but no Takeover

Hi i managed to get the remote start to work on an outlander 2014 mk3 2.2 diesel. I had to use the OBD for CAN1 Hi/Lo as the guide wires did not work, it was after this that I was able to program the evo all correctly and remote start the car. if I remote start the car, unlock doors with key and then press brake, the car turns off and I manually start it again. This works perfectly and there are no errors. however, when I press the push to start button to takeover It doesn't work and I get an immobilizer error and electrical system service error on the cluster. Why could this be?

0

Mirage Evo-all

Can i remote start a 2017 Mirage with Evo-all and the OEM key fob or do i need to install anything else? And if i need what do i need to install. Thank you

0

WIRING DIAGRAM

Hello Does anyone have a wiring diagram for a 2017 Mitsubishi Mirage for Evo-All

0

ct5072 and im using evo all for 2008 mit lancer,what kind of wire to use for d2d? can i get diagram too?thanks

ct5072 to evo all d2d pinout

0

immobilizer system service required error after RFK kit install - car will no longer start with original key

Remote start was programmed and worked perfectly, however the takeover sequence only worked by pressing brake and restarting the car with original key. I just installed the RFK912 and progammed it corectly, the car worked fine starting from the rf remote and original remote. The car both remote started and then after shutting down started normally with the original fast key. The same night, after starting with the RF key and shutting down pressing the break, the car no longer starts with the original key and shows the immobilzer system service required fault. I can still remote start the car but cant use the original remote to start and drive away. after removing the evo-all - the car shows the same fault. It is stuck where it is. i tried to use teh dcrypot but it needs resetting - i want to reflash the dcryptor and try starting again. SN 001A07140493 the car is MITSUBISHI OUTLANDER 2014 EURO

0

Unit doesn't flash blue rapidly

During programming I let off the button at blue, reconnect everything, push to start button twice but it doesn't flash blue rapidly, just shuts the light off. When I connect it to dcryptor, it says the information was not complete

0

EVO-ALL StandAlone A2/Purple/Lock and A3/PurpleWhite/Unlock Availabilty?

RE: EVO-ALL Stand Alone Installation in 2017 Mitsubishi Outlander (NOT Sport) with Push-To-Start (FastKey) While installed in this manner, can the can the A2/Purple negative input lock trigger and A3/PurpleWhite negative input unlock trigger wires be used to send lock/unlock signals onto the CAN BUS? If yes are there any restrictions? If EVO-ALL alarm mode is enabled, must it be disarmed first, or will negative unlock trigger via A2/purple still operate? The intent here is to create an alternate mechanism to unlock the car for when it is more convenient to leave my keys inside (with FastKey properly RF shielded of course). If the CAN BUS lock/unlock interface in the EVO-ALL is enabled in this mode, then that will make the installation trivial as it is already present. Thank you.

0

EVO-ALL StandAlone A2/Purple/Lock and A3/PurpleWhite/Unlock Availabilty?

RE: EVO-ALL Stand Alone Installation in 2017 Mitsubishi Outlander (NOT Sport) with Push-To-Start (FastKey) While installed in this manner, can the can the A2/Purple negative input lock trigger and A3/PurpleWhite negative input unlock trigger wires be used to send lock/unlock signals onto the CAN BUS? If yes are there any restrictions? If EVO-ALL alarm mode is enabled, must it be disarmed first, or will negative unlock trigger via A2/purple still operate? The intent here is to create an alternate mechanism to unlock the car for when it is more convenient to leave my keys inside (with FastKey properly RF shielded of course). If the CAN BUS lock/unlock interface in the EVO-ALL is enabled in this mode, then that will make the installation trivial as it is already present. Thank you.

29/01/2019