Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

21/03/2023

 GMC Mundher Sulaiman (170Pts.)

0

Lock door with not working

Hi, Can you please check this video link below: https://www.youtube.com/watch?v=Nd5qKrlF8so I have GMC Yukon 2006, I installed EVO all and excalibur X70-b, when start a vehicle by OEM remote or OMEGA remote all doors not locked when I shift a gear however when I start a vehicle by key as a normal starting all doors locked normally. Can you help me please.
Login to reply View 1 answer(s)

17/02/2023

 GMC Daniel Murry (220Pts.)

0

Do the fortin evo all work with a prestige remote starter? I have everything else working but the remote start will not.

The evo all is updated where it needs to be and it programmed also.
Login to reply View 1 answer(s)

29/12/2022

 GMC Kevin Hawkins (130Pts.)

0

2010 Sierra Standard Evo-All THARGM4 No Alarm Functions

Programming was successful, vehicle starts, door locks continue to work via factory remote. Evo-all seems to be monitoring door switches as it will shut down if a door is opened when locked. However no alarms sound whether that's the factory alarm or evo-all. What could be the problem here? I was looking to supplement the factory alarm with evo-alarm for shock/glass break sensors. I'd settle for just the factory alarm working again.
Login to reply View 1 answer(s)

12/09/2021

 GMC Mundher Sulaiman (170Pts.)

1

Car goes off after 20 seconeds the goes on.

I have Yukon 2005, I install on it EVO All + excalibur 70X when I start it by remote (OEM,Excalibur additional remote or from door lock switch) a car still working for 20 seconds then goes off and automatically started again, This problems stay for 3 times then a car switched off, I make reflash a Fortin but same issue, I replace it with Excalibur 70B also same issue, I checked all wiring every thing in good condtion. But if I start a car by Key it's working fine without any issue. This issue suddnly happend with me started before 3 weeks from now but before it's working fine. Car battery is new I replace it before 5 months. There is any thing need to check it more? please I need help, also I install same devices for many cars I don't face same this issue with any car excepte my car. Please check this issue on YouTube I uploaded a video for this issue: https://www.youtube.com/watch?v=qFL4xSWzhvM
Login to reply View 1 answer(s)

07/09/2021

 GMC Daniel Murry (220Pts.)

0

02 gmc yukon tried connection 3 and program 3 but didnt program. Should i down grade it to 4.06?

I have the evo all updated to the latest software, which maybe the problem.
Login to reply View 1 answer(s)

03/05/2021

 GMC Kyle Smith (130Pts.)

0

2014 GMC Terrain not starting with 3x lock

Installed evo-all stand alone remote start through step 11 correctly and received flashing blue at the end. Updated options including turning on 3x lock and bypass hood safety. Saved the options. Flashed the unit. Tried to start by 3x lock but did not start. The unit flashes blue and still able to use the remote to unlock the vehicle. What have I missed?
Login to reply View 1 answer(s)

06/03/2021

 GMC David Gates (160Pts.)

0

2009 GMC Sierra shuts off as soon as the key is inserted into the ignition. Evo all with t harass install.

Remote start fine but engine turns off as soon as key is inserted
Login to reply View 1 answer(s)

13/01/2021

 GMC Randy Bard (130Pts.)

0

Programmed but won't remote start 2015 terrain flip key..Evo one t harness

Blue light on module
Login to reply View 1 answer(s)

31/12/2020

 GMC Tyrell Gray (130Pts.)

0

EVO-ALL won’t switch from yellow light to red light after I start engine during programming.

2018 GMC Terrain using EVO-ALL and thar-gm6, yellow light turns solid but won’t switch to red while programming, tried reset and re flashing but still won’t work, light blue is connected to light blue/black.
Login to reply View 1 answer(s)

03/12/2020

 GMC Brian Pretzer (160Pts.)

0

Best options to use with Excalibur AL-1870-30B

Installing Excalibur AL-1870-3DB 2-way remote start and alarm into my 2007 GMC yukon using evo-all with t-harness and data-link. I'm just double checking the best options to use on the flash link manager to get full use of my excalibur system and especially the 2-way system part of it. Also settings you recommend leaving off and any other wiring conections not supported by datalink other than ignition, 12v and ground. Any and all advice is much apreciated, the more info the better. Hoping to get everything installed Friday or Saturday (12-4-2020/12-5-2020) Thank You.
Login to reply View 1 answer(s)

06/09/2020

 GMC hassan baza (160Pts.)

0

no thing work

all butom on the remote control are not working
Login to reply View 1 answer(s)

04/09/2020

 GMC hassan baza (160Pts.)

0

i tried to start the car using the remote control but it didn't start

my 2012 gmc terrain has evo all and nano GM1 the antena blue light not flushing it just on
Login to reply View 1 answer(s)

11/08/2020

 GMC Patrick Fennell (130Pts.)

0

Reflash limit reached

I am trying to repair a customer's remote start, EVO ALL module is doing nothing. I reprogrammed it, and it says limit reached on dcrytor. Can you please reset for me. Thank you. Service number: 001A06 247248 hardware vr:6 Firmware Vr 4.8 Date 10/13
Login to reply View 1 answer(s)

17/02/2020

 GMC Tom Cook (130Pts.)

0

My 2011 GMC Sierra won't start by key with just the T harness THAR-GM4 completely plugged in.

With the T Harness plugged into both connections without the EVO-ALL connected the key will not start the engine. If I disconnect the CAN Bus connecter and reconnect the factory CAN Bus connecter the truck starts by my key. So I guess my question comes down to does the EVO-ALL have to be plugged into the T Harness for me to use my key? The harness is THAR-GM4
Login to reply View 1 answer(s)

01/02/2020

 GMC D L3 (160Pts.)

0

Wiring diagram 2003 GMC Sierra 1500 Standard Key, EVO-ALL, STANDALONE

Hello,

I have Evo-all Guide #61111 for GMC Sierra 1500 Standard key, but this is for Regular Installation using separate remote starter and Data-link.

I need the guide for a Standalone installation where the EVO-ALL is the remote starter with no data-link.  Or I need the rest of the pin-out for the 20-pin connector.  The pin-out does not indicate the corresponding pin for the main connections?

What is function is: OUT A5 / IN A6 / IN A7 / IN A9 / A10 / OUT A11 / A17 / A18 / A19 ??

Example, the RS7 OUT - Starter (+).  No 'Ax' corresponding designation for 20-pin connector, is A6 - starter, A7 - Ingition2, etc?

Please advise trying to install EVO-ALL as standalone remote starter in 2003 GMC Sierra 1500 with Standard Key, factory alarm, no heated seats, or heated mirrors, flashed with 70.18 firmware.

Login to reply View 0 answer(s)

04/01/2020

 GMC D L3 (160Pts.)

0

Firmware Discrepancy

2003 GMC Sierra 1500 Standard Key, with keyless entry and alarm system.  Working with an EVO-ALL, date 4/2019, firmware 70.18, using Flash-Link 4 with hardware version 4, firmware 4.05, date 11/2019.

Website indicates firmware minium version is 70.21 for both EVO-ALL and EVO-ONE.  However, above min version for the EVO-ONE has note that minium version is 70.18? Does that apply to EVO-ALL as well?

On the installation guide #61111 it states minium version is 70.32!?

Which is the correct firmware?  xx.18, xx.21, xx.32?

Using FlashLink Manager 4.51, I am only offered firmware 70.18 for a 2003 GMC Sierra 1500 standard key.

If the minuim is different than 70.18, then where can I download the correct firmware?

And please tell me this is a stand alone remote starter which is going to start the truck with 3x lock on the OEM remote?

Login to reply View 1 answer(s)

25/11/2019

 GMC moosespectacles (160Pts.)

0

Fortin EVO-GMT6 remote start not working after following guide #77231

For starters, my car is a 2018 GMC Terrain with push to start. I followed all of the instructions and wiring exactly, even with the help of crutchfield, and for some reason the car is still not starting up when I press lock 3x. When I press the lock and unlock buttons the evo-all unit led blinks blue, but that's it. Can anyone please help me resolve this issue? Any help will be greatly appreciated. Thank you in advance.
Login to reply View 1 answer(s)

24/10/2019

 GMC steve henry (130Pts.)

0

04 yukon wont program

hi my evo all wont program in my truck. ive tried the recomended firmware and still nothing. i hold button plug in connector till blue light on let go plug all others in turn key red light comes on and stays on and blue light flashes. what am i doing wrong please help.
Login to reply View 1 answer(s)

04/04/2019

 GMC ajay kumar (190Pts.)

0

Compustar prime 2way communication doesn’t work

Compustar prime 2way communication doesn’t working but working perfectly as one-way. I have connected ft-d100, with blue and white wire swapped as it was in guide, idk what’s the problem,
Login to reply View 2 answer(s)

19/03/2019

 GMC ajay kumar (190Pts.)

0

EVO-ALL GM1 v2. no engine start. 2012 GMC Terrain, red led blink more then 5 times

i did programing, wiring are good i think, my RF remote and ome remote working good with lock and unlock, when i try to remote start blue led blinks 3 times, and red led bkinks more then 5 times acc turn on, door locked but no crank, after some second yellow led comes and quicky goes, i did master reset also, i did programing also, but no success. plz help me im trying to fix remote star from long time, there is 12v also on yellow wire from 20 pin connector when engin running, i tried with Lt.blue/black and Lt blue connected and without it.
Login to reply View 1 answer(s)

20/02/2019

 GMC Shane Guilliams2 (130Pts.)

0

Red LED on EVO-ALL but car will not crank. Dash and accessories come on after 3x lock with solid red led but no crank.

I believe programming was successful as the evo blue led flashes blue with remote lock presses. Red led comes on solid but with no engine start. 2016 GMC Terrain
Login to reply View 1 answer(s)

01/01/2019

 GMC Jeff Porter (130Pts.)

0

2016 Terrain will not remote start.

Started one time. Now when I try to start the parking light flashes twice after the 2nd attempt to start.
Login to reply View 0 answer(s)

11/11/2018

 GMC Quincy Brownlee (150Pts.)

0

Everything but starts

2014 GMC Terrain goes through the process when I press lock 3x but does not start the ignition.
Login to reply View 1 answer(s)

28/10/2018

 GMC timmerk (950Pts.)

0

Door status not outputted for 5-6 seconds after remote shut down

I have a recent EVO-ALL (hardware v6, firmware v70.35) on a 2008 GMC Sierra connected to a third-party remote starter (i.e. *not* in stand-alone mode). It works perfectly except for one bug: once the EVO-ALL initiates a shut-down, it doesn't monitor and/or output the door status untill about 3-4 seconds after the vehicle is shut down. The door status is outputted correctly if engine is still on or if I wait 3-4 seconds after shut down before opening the door. Could you please ask your developers if this could be fixed in a firmware update? Thank you! UPDATE: it sounds like there are relays in the EVO-ALL, and the door status isn't outputted until after the relays "click" off or on after a remote shut down. This click occurs 5-6 seconds after shutdown, so hopefully this will help your developers out.
Login to reply View 1 answer(s)

06/10/2018

 GMC Matthew Reed (130Pts.)

0

Standare or Standalone?

service number 001A06 556424 2016 GMC Sierra 2500 Diesel, automatic, standard key, ON-Star I have the EVO-ALL module and the GMT-3 harness. All seemed to go well on the install but have questions and ready to put the firmware in and do programming. 1.Document indicates Lock/Unlock wires not needed with On-Star. Advise. I've only connected parking lights and CAN-BUS line. 2. When selecting firmware, I get standard or stand-alone question. Unsure of the difference. Also - what is the CORRECT document I should be looking at for following the complete installation for my setup. Thanks! Matt Bettendorf, IA
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue