Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

08/01/2022

 Pontiac matthew haney (170Pts.)

0

2004 Pontiac Vibe Install

I am trying to install a Evo One on my 2004 Pontiac Vibe. It dose not have a transponder and i can not seem to get it work under the no vehicle specific install through the update software. What is the best firmware to use since there is none listed for the Vibe till 2008?
Login to reply View 2 answer(s)

08/01/2022

 Pontiac matthew haney (170Pts.)

0

2004 Pontiac Vibe Install

I am trying to install a Evo One on my 2004 Pontiac Vibe. It dose not have a transponder and i can not seem to get it work under the no vehicle specific install through the update software. What is the best firmware to use since there is none listed for the Vibe till 2008?
Login to reply View 2 answer(s)

26/12/2020

 Pontiac Steven Smith2 (130Pts.)

0

is there a t harness for an 2007 pontiac g5

is there a t harness for an 2007 pontiac g5
Login to reply View 1 answer(s)

12/09/2020

 Pontiac Raul Ramos (460Pts.)

0

2016 Jeep Wrangler Viper 4606v evo all

I installed viper 4606v and evo all d2d mode everything working good the problem was the car crank but won't start And start after 2 or three times do you recommend programming tach?
Login to reply View 1 answer(s)

31/03/2020

 Pontiac rob Haretzmuller (220Pts.)

0

Remote start help

I have installed a cs800-s on a 2005 pontiac wave. I only connected the start function, no door locks, horn,lights, ect. When I start the vehicle the alarm goes off & i loose the door locks on the original remote. Also see there is PATS wiring on the wire color shhet , what is this for? Thanks in advance Rob
Login to reply View 1 answer(s)

16/12/2018

 Pontiac Joshua Halsey (630Pts.)

0

Anyone successfully done a 2007 Grand Prix with an Evo one?

Wondering if anyone has done a 2004-2008 Grand Prix with an EVO ONE. If so which firmware? I know that it relies on the J1850 but I am unsure of which firmware would make that work properly and the programming for said creature......
Login to reply View 1 answer(s)

03/11/2018

 Pontiac trevor gorniak (2230Pts.)

0

Bypass solution for 2005 Pontiac vibe

Cannot find a solution for the bypass module on 2005 Pontiac vibe
Login to reply View 1 answer(s)

03/05/2018

 Pontiac mike hairston (130Pts.)

0

installing cs800s w fortin int-sl+ every thing works fine while key is in switch what am i not getting hooked up

unit will remote start with key in switch but wont when i take it out am i missing some connections
Login to reply View 1 answer(s)

05/07/2017

 Pontiac Mohammad Odeh (420Pts.)

0

cruise control is not working after install the Evo One on Pontiac pursuit

cruise control is not working after install the Evo One , and also the Door lock unlock from remote is not working only from the door lock inside the door itself but nor remote , the cruise control is not working after install the evo one it was working before install and it s normal , the light is show but the speed will not set at all even at speed over 50 or even 100 , any suggest what is the problem could be and what is the solution for it.
Login to reply View 2 answer(s)

05/07/2017

 Pontiac Mohammad Odeh (420Pts.)

0

cruise control is not working after install the Evo One on Pontiac pursuit

cruise control is not working after install the Evo One , and also the Door lock unlock from remote is not working only from the door lock inside the door itself but nor remote , the cruise control is not working after install the evo one it was working before install and it s normal , the light is show but the speed will not set at all even at speed over 50 or even 100 , any suggest what is the problem could be and what is the solution for it.
Login to reply View 2 answer(s)

29/05/2017

 Pontiac Charlie Moore (920Pts.)

0

Missing Data wire

I'm installing a evo all with a Ultrastart remote start module on a 2009 sv6 there is no tan/white wire in c1 pin 37 at bcm. for data is there another spot to pick this up?. Also wire diagram does not show remote start module wiring?
Login to reply View 1 answer(s)

08/01/2017

 Pontiac Ross Jordan (130Pts.)

0

2007 Pontiac G5, Manual Transmission, Evo-One, how to wire clutch bypass

Just wondering how to wire in the clutch bypass.
Login to reply View 0 answer(s)

19/12/2016

 Pontiac Jeffrey Drije (170Pts.)

0

LED does not flash during programing. 2005 Pontiac G6

I am using the int-sl+ with compustar cs800s. All of the compustar functions work with the datalink connection through the int-sl+. When I hit the lock button on the cs800s remote, the LED on the int-sl+ flashes once, but when I turn the ignition key on it never flashes. I have the purple/white data BCM wire hooked to the keyless data wire at the bcm. I have updated the int-sl+ to version 3.06. I have checked for 12v on the pink ignition wire and have it. From the cs800s remote the doors lock/unlock, the trunk pops, and when you try to remote start the fuel pump, dash lights, blower motor all come on. Just no crank and start. To clarify programing the int-sl+, I push the program button and plug in the datalink connector, then release the button. The LED comes on when I connect the datalink. Then I connect the white connector. The LED stays on. Then I push lock on the cs800s remote. The car locks and the LED goes off. Then I turn the ignition key to on and nothing happens from there.
Login to reply View 1 answer(s)

04/12/2016

 Pontiac Mohammad Odeh (420Pts.)

0

FX64-2W WITH EVO ONE pontiac pursuit

FX64-2W not working with evo one , i connect all wires to the care it is without T harness, now when i try to program the key fob the LED on antenna not flashing it is just flash once when i connect the 4 pin blue wire small one , i am confused because the 4 pin port on evo one as chart H is for antenna which i don't have cable for it but the other blue port small i have cable for it,.
Login to reply View 1 answer(s)

05/11/2016

 Pontiac Micheal Unger (2680Pts.)

0

INTSL+ 2003 Pontiac Montana security light takeover

Installed an autostart remote start and INT-SL+ into a 2003 Pontiac Montana and everything seemed to go well until it was all back together and tried to do a key takeover the security (lock symbol) icon is displayed in the information centre on the instrument panel. Tried the Q and A and followed instructions to cut Orange PK3 wire and atach one side to yellow and the other to yellow/black of the INT-SL+, tried this and did not change. Tried updating the firmware to V3.06, thought I had it fixed until vehicle was put back together and security icon still comes back on. Everything is normal starting the van with the key, everything is normal when remote starting. It's during takeover when the key is put into run and brake is applied to shut off remote starter that the security light comes on solid and stays on until vehicle is shut off and restarted with they key. Any suggestions, other than black tape over the light?
Login to reply View 1 answer(s)

15/11/2015

 Pontiac LexMark (190Pts.)

0

Pre loaded EVO-FORD , EVO MAZDA that is flashed to Pontiac would it work?

I purchased EVO-ALL and flashed to 2008 Pontiac G5 and installed it to using ProStart. Guide # 46721. But it wont crank/start. Double checked all connections - all good. Uses a trouble shooting guide with no avail. I just noticed that at the back of EVO-ALL unit , it says " EVO-FORD , EVO MAZDA pre loaded ". Could it be the cause?
Login to reply View 1 answer(s)

19/04/2014

 Pontiac Marc Voyer (920Pts.)

1

Is there a way to bypass 1998 Grand-Am with a single wire to Car Data Connector pin # 2 or Pin #9

We are building a Snow plane with a 3.1 GM from a 98 Pontiac grand am. I know the VATS send info to PCM via data wire pin # 9 on Car Data Connector. can I try a evo all to achieve same thing ? We don t want to install cluster and key cylinder in machine thanks.
Login to reply View 1 answer(s)

26/02/2015

 Pontiac lary smith (160Pts.)

0

so i conect a 180 ohms resistor between the clutch switch and ecm?

so i conect a 180 ohms resistor between the clutch switch and ecm? or the remote start and green wire?
Login to reply View 1 answer(s)

22/02/2015

 Pontiac lary smith (160Pts.)

0

2010 pontiac g5 clutch bypass

i have a evo all conected to a titan ts3000 for manual trans and i cant find how to bypass the clutch. it will start in reservason mode with the clutch prest in.
Login to reply View 1 answer(s)

15/01/2014

 Pontiac Willy Friesen (200Pts.)

1

2004 montana doesn't start

prostart installed, evo-all installed with 4.06 firmware. cammand start activates all lights but does not attemp to start the engine, no crank. wheres the problem?
Login to reply View 2 answer(s)

15/01/2014

 Pontiac Willy Friesen (200Pts.)

1

2004 montana doesn't start

prostart installed, evo-all installed with 4.06 firmware. cammand start activates all lights but does not attemp to start the engine, no crank. wheres the problem?
Login to reply View 2 answer(s)

13/01/2015

 Pontiac Scott Eccles (130Pts.)

0

Would a 2007 Pontiac Vibe be the same as a 2007 Toyota Matrix?

I have someone looking to install a remote starter into their 2007 Pontiac Vibe. Fortin has nothing listed for older than 2008 Vibes. However they do have applications for 2007 Toyota Matrix. Are they not the same vehicle?
Login to reply View 1 answer(s)

06/01/2015

 Pontiac Josh Ley (500Pts.)

0

Evo all rap shutdown bonneville

Still haven't resolved this issue-2002 bonneville evo-all not shutting down RAP system
Login to reply View 1 answer(s)

05/01/2015

 Pontiac Josh Ley (500Pts.)

0

EVO-ALL not shutting down RAP 2002 Bonneville

Installed INT-SL+, flashed to 3.06, would not program. Flashed to several other versions, still wouldn't program. Removed and installed EVO-ALL, firmware 4.06. first issue: service theft system indicator lights up on the dash when using the remote start. It starts and runs normally when remote started, just the message is displayed in the vehicle information center. second issue, RAP does not shut down after aborted remote start. Guide indicates that this function is compatible with given hardware/firmware.
Login to reply View 1 answer(s)

28/12/2014

 Pontiac tjamz0061 (340Pts.)

1

08 Pontiac Torrent Won't program

So I'm attempting to install an EVO-ALL along with an Ultrastart 3295 remote start. Firmware Version 70.16 When I go to program the blue light goes out and never starts flashing when I get to step #4. At first I noticed the car wouldn't start this way either. Ultimately I determined it was because there wasn't power passing through the White Green wire on connector D to the White Red wire on connector D so I unhooked the entire remote start & bypass module and jumpered the two wires together to verify the car would start that way (it did). Next I reconnected the starter and bypass and removed the jumper that I had temporarily installed and tried programming again... same issue. Anyone have any suggestions?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue