Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

Questions & Answers

Browse among the most frequent and popular questions and find accurate answers.

recent questions tagged: ...

Clear All
Collapse All
Expand All
Clear All
Collapse All
Expand All
picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask us a question
RÉCENT HOT! MOST VOTES MOST ANSWERS MOST VIEWS

10/03/2023

 Honda KaPa (320Pts.)

0

Honda CR-V 2016 PTS AT Does not start with cold EVO-ONE

Hi My CR-V 2016 PTS diesel automatic transmission does not start when temps are cold outside. Fortin tries 3 times as programmed, lights turn on, but car wont start. I think issue is that when temps are cold, car usually takes 3-5 seconds depending of temps to prime something before igniting car and i think its not enough for Fortin and it cancels and tries again. When programming Fortin what parameter should i change to wait it out?
Login to reply View 1 answer(s)

19/01/2023

 Honda KaPa (320Pts.)

0

Honda CR-V 2016 PTS AT starts moving when Evo_One remote started

Hi Great product and super easy installation, thank You. But when I remote start my Honda CR-V 2016 i-Dtec (N16A4) car sometimes does a half wheel turn forward. My model has push button parking shift and it automatically engages when i turn off engine. I guess when it is remote started it remembers settings just before turning engine off as A/C has same temp as when i turned off engine and seat heaters also and if parking gear automatically shifted it will start with same in drive mode and moves until parking shift automatically engages. Should i change some off the settings to get it to start with set parameters and not last used settings? FYI i didnt connect parking lights and horn, because i didnt need them.
Login to reply View 2 answer(s)

19/08/2022

 Honda Munito (1450Pts.)

0

HONDA CR-V 2018

Hi dudes. HONDA CR-V 2018 wire colors doesn't match. Can I use this colors order instead? Cuz in the scheme only the ignition connector match. Please and thanks you.   https://ibb.co/rsk37g3 https://ibb.co/JkSF2Wv https://ibb.co/vJnQbNR https://ibb.co/5KqkYB5  
Login to reply View 1 answer(s)

29/01/2021

 Honda Ketch Samson (130Pts.)

0

honda CR-V 2017 LX won't start after installing the module after decryption

iI followed the guide for honda cr-v 2017 lx key start option. and done all the pairing process and the decrytion process, then after that i installed everything back all the pins to car. there is no light on the module awhen all pins were connected back, i went outside my car and tried to remote start my car while looking inside to the module while i press 3 X lock no lights on the module everytime i press the 3X lock start procedure. my car won't start at all. please help thank you!
Login to reply View 1 answer(s)

17/12/2019

 Honda Timothy Schultz (150Pts.)

0

2005 Honda CR-V evo-one won’t program

2005 Honda CR-V: Evo-one will not program. I completed the flash link with the evo-one and everything is said to be correct. I'm using for both bypass and remote start from factory key. I installed wiring based on the online manual for the 05 crv following connection #2. main 6 pin harness: red to 12v (white) yellow to starter (black/white) Pink to ignition (black/yellow) with the added yellow wire from ignition A plug black is grounded orange accessory to accessory (black/red) white to blue parking lights A plug: yellow to pink ignition, light blue data to white wire on pin two of cylinder harness, and foot brake wire to foot brake (white/black) right above the brake pedal. D plug: the five pin at the key cylinder (blue/orange) was cut. The white green was attached at the key side and white red attached toward hood side as shown. I have power to the evo-one and following the manual to enter program mode by pressing and holding down program button and plugging in power I get the lights going through the flashing sequence, however I do not get the solid red. Am I doing something wrong here or not waiting long enough? Is wiring right? All wiring is soldered connections. I appreciate any help.
Login to reply View 1 answer(s)

14/02/2019

 Honda Jasminko Corbic (130Pts.)

0

Help with evo one that programs successfully but does not start the vehicle

I have 2015 honda crv push to start. I installed evo one with t-harness THAT-ONE-HON3 rev.2. Followed the guide #57131. Everything programed correctly. I wanna use oem remotes by pressing 3x lock to start my car. However it does not work. Blue light comes on evo one every time I press lock on the remote but does not start the vehicle. No red light. When I start the vehicle manually by pressing the brake and pushing the start button I have a yellow light on the evo one. I hoppe somebody would help me to figure this out. Thanks in advance
Login to reply View 1 answer(s)

23/01/2018

 Honda Mohammad Odeh (420Pts.)

0

Honda CR-V 2014 Evo one

i have honda crv 2014 standard key , and i am installing evo one with T-harnes 2 and RF2W antina fob , i connect same what is show , i and i follow the instruction solied red then push twich flash red , then pust the key to ignition fast red falshing but the blue light will not show after 10 flashing and even at all all the wires are connected by the T harnes and the orand wire and the pink wire are connected for each connecter 12 pin and the 20 ping , the ground is connected , the only wire is not connected is the fuesed wire which is pin 1 white or brown in the T harness which is said it is output , i never touch the programming yet for the interface of the unit which is still the default setting from the manfacure , any advice or suggestion . ?

 

is the E1 wire with the Fuse should be connected or not , the installation manual it is show 2 diffrent way , i am using the Rev 2 Thar hon 2

 

Service NO 002b07228755

Login to reply View 1 answer(s)

22/01/2018

 Honda Mohammad Odeh (420Pts.)

0

Honda CR-V 2014 Evo one

i have honda crv 2014 standard key , and i am installing evo one with T-harnes 2 and RF2W antina fob , i connect same what is show , i and i follow the instruction solied red then push twich flash red , then pust the key to ignition fast red falshing but the blue light will not show after 10 flashing and even at all all the wires are connected by the T harnes and the orand wire and the pink wire are connected for each connecter 12 pin and the 20 ping , the ground is connected , the only wire is not connected is the fuesed wire which is pin 1 white or brown in the T harness which is said it is output , i never touch the programming yet for the interface of the unit which is still the default setting from the manfacure , any advice or suggestion . ?
Login to reply View 1 answer(s)

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue