FAQ usager

12/01/2017

Buick Bill W (1850Pts.)

0

EVO-ONE is preventing my physical key from starting my car.

The EVO-ONE installed in my 2003 Buick Century prevents my car's actual starter(not remote starter) from cranking for 5-10+mins at a time. Here is the rundown: -Unlock car and start with actual key=no issue. -Remote start car with Fortin RF kit, hop into car, insert key and turn ignition to run position=no issue. Here's where it gets weird... -Remote start the car with Fortin RF kit. Car starts and is running. -I hop in and insert the key into ignition but "forget" to turn the ignition barrel at all. -I hit the brake, as you would before putting the car into gear and the car shuts off, as it should, due to the ignition barrel not being turned to "run" position before the brake tap. -After the car has shut off due to tapping the brake before turning ignition to "run", I turn my key that is in the ignition barrel already and my car's actual starter willl not even attempt to crank. All other items in the car turn on as they should(i.e. radio, air, fuel pump primes, etc.). EVO will turn the car on but will not even try and crank the starter if I try to remote start again at this point. -I wait about 10mins and then try a few more times with the actual physical key and the car will start now. So after the car comes back alive, I can turn it on and off with the key a million times in a row just fine. I go and repeat the remote starting and put the key in ignition(but not turned to "run") and tap the brake to shut the car off and the car now will not start again. I can replicate this every single time I do what I described above. This problem cost me $200 and and hour on my back in 5F weather putting a new starter in about a month ago because I figured the starter solenoid died on my wife. Why would this be happening? This car is equipped from the factory with an anti-grind relay. It's acting like anti-grind relay thinks the car is trying to double start, which it's not.

evo-key-not-work

Connectez-vous pour répondre Voir 1 réponse(s)

02/01/2017

Buick Bill W (1850Pts.)

1

Evo-One responds to commands over Fortin RF642W kit poorely.

Commands given from the RF642W two way kit are unreliable. Lock and unlock commands do not work 1/4 or more of the time, even when standing within 10ft. of the antenna. The remote beeps as if it has made communication with the car but the lock/unlock commands do not register. Improper status is also given commonly when using the status request feature. I have gotten confirmation that the car is locked on multiple occasions when the car is surely not locked. This RF kit is spotty at best, what gives? Is there better firmware or something? Antenna is mounted in the front window and has no obstructions. Lock and trunk commands are being fed over OBD. Car is a 2003 Buick Century.

evo-one

rf-kit

unreliable

Connectez-vous pour répondre Voir 1 réponse(s)

12/12/2016

Ford Francisco Ribeiro (130Pts.)

0

What Extra wires no need to be connected (Mandatory)? FORD EDGE 2013

I am trying to install my EVO into my Ford EDGE 2013, according the manual athttp://fortin.ca/download/34421/evo-all_ig_tsa_bi_for1-80bits_c_34421.pdf, and I am having a problem, so I have some questions if you don't mind in answer please:

1) I am wiring only the connections for CAN high and Low (C3 and C4), and A1, A20 and A10 to the 20 pin connector ( not wiring/connecting A17, A18,A5, A19, A8, A14 and Parking lights). It should work with these connections out or they are not optional?

2) Manual shows Yellow/BLACK wire to be connected to YELLOW ( not yellow black) into 20 pin ( is that correct?)

3) I am able to proceed with all programing steps and leds as shown in the manual, but when I Press Lock 3x, nothing happens, the engine does not start. Am I missing some mandatory connection?. What are the mandatory and optional connections in this schema ?

Connectez-vous pour répondre Voir 3 réponse(s)

11/12/2016

Buick Bill W (1850Pts.)

0

Wired exactly as the install guide said but car won't even try to crank.

Installed an Evo-One and Fortin RF642W 2 way RF kit in a 2003 Buick Century. Followed "connection 1" and "programming 1" as stated to by this install guide. http://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf

All wiring has been verified multiple times to be exactly what the install guide said to do...nothing more and nothing less.

When I try to remote start the car, via the 2 way remote, the car will power on but will not crank the starter at all. When I use the remote to kick the car into "idle mode", the car unlocks as it should but shuts off when I turn the ignition off to pull the key.

Bypass portion programmed fine....RF remote also programmed fine.

Literally, the only wires connected at the moment are what the install guide I linked above says.

buick-century

no-crank

power-no-crank

Connectez-vous pour répondre Voir 2 réponse(s)

04/12/2016

Buick Bill W (1850Pts.)

0

Does the Evo-One work as a remote starter for a 2003 Buick Century?

I do not see "remote start" mentioned in the features listed for this car for the Evo-One.

Does the Evo-One work as both the bypass and remote starter for a 2003 Buick Century?

Would it require more wiring than what is shown here(install #1 in the link)? https://fortin.ca/download/23261/evo-one_ig_reg_bi_gm_j1850_b_23261.pdf

buick-century

remote-start

Connectez-vous pour répondre Voir 1 réponse(s)

20/03/2016

Nissan Bill W (1850Pts.)

1

Does Evo-One starter firmware .51 have all the improvements that firmware 1.18 brought?

Is firmware .51 the same as 1.18 aside from the "lock only at brake tap" option being available through RF kit programming? I know .51 was made after the 1.18 release but I am not sure that means .51 is a built off of 1.18. I am primarily concerned about the temp sensor setting that was updated to a higher temp in firmware 1.18. My defrost works reliably with 1.18 but does not with the lower temp setting of all the previous firmware versions. I need to retain this functionality if .51 is going to be my only "solution" to that head light problem.

maxima

firmware-

51

Connectez-vous pour répondre Voir 1 réponse(s)

14/02/2016

Chrysler Yaroslav Halchenko (130Pts.)

0

Having being remote started stops responding to remote unless really near by the car

I got EVO-CHRT4 (with the flashlink, so updated everything to up-to-date at that point) for Chrysler Town & Country 2013 in early Dec 2015, and installed it somewhere mid December 2015. I don't have FW versions from top of my head, and the unit is mounted in the car and it is cold outside ATM (NH). Originally everything worked out splendidly. But since probably a month ago (I haven't done anything to the car since then, may be washed it once or twice ;) ) I have started to observe that having started the car remotely, the car stops responding to the fob/remote -- I can't unlock the car, or open side doors, anything, UNLESS I come really close to the car, like to the driver's door. I have tried with the 2nd fob/remote -- the same story -- no reaction. What could be the reason? I did recently change battery in one of the remotes. Car does pick up my presses originaly from about 60-100m.

evo-chrt4

Connectez-vous pour répondre Voir 1 réponse(s)

14/02/2016

Nissan KS (130Pts.)

0

Car Shutoff after 15 minutes - even when driving

I've installed EVO-NIST1 in Nissan Altima 2012 2.5S (Push to Start), connect all the cables as per installating guide. I'm using my OEM Key Fob to remote start by pressing lock 3x. I've configured EVO to run time 15mins. It's working fine after 15min car shutoff if you don't drive. But if I start remotely and dirve within 15mins ( unlocak car using Remote and dirve), Car SHUTOFF exactly 15min after I started remotely, even I'm driving. It happened with me more than 4 times, thank GOD I was on signal stop when 2 times it happned and the two time when I drove and was in parking lot. Car shutoff. I've to start by push to start.

These days what I'm doing is start car remotely so car can heat up and when I need to drive, I've to shut off by pressing break and start again to make sure car doesnt shutoff in middle of highway.

Let me know if I'm missing any configuraiton.

thanks

Connectez-vous pour répondre Voir 2 réponse(s)

14/02/2016

Nissan Bill W (1850Pts.)

0

Why does my physical key not turn my ignition without the EVO-ONE installed?

2007 Nissan Maxima w/Intellikey Using a T-harness and a Evo-One. When the Evo-One is removed from the car, my physical key will not allow me to turn the ignition barrel. It is not a timed lockout as I let the car sit for over 24hrs without the Evo and I still could not use my physical key. If I plug NOTHING but the red connector into the Evo(not even the power cable), then I can use my physical key in my ignition barrel. Without the red harness connected, I can NOT use my physical key. However, my Intellikey still unlocks the barrel and starts the car just fine without the Evo installed, it's just my actual physical key that won't work. Why is this?

nissan

ignition-locked

physical-key-not-working

Connectez-vous pour répondre Voir 1 réponse(s)

09/02/2016

FAQ Tager Tower (3480Pts.)

0

Can I drive my car without a valid key?.

Hello,

Can I drive my car (not remote start) without OEM key? if I nstalled

1- EVO KEY or,

2- EVO ALL or,

3- EVO ONE.

Connectez-vous pour répondre Voir 1 réponse(s)

24/01/2016

Nissan Brittany Gadd (180Pts.)

0

2008 Nissan Altima engine shuts off when door opens

I have just installed the EVO-ALL in my 2008 Nissan Alitima (push to start). All features are working properly, such as door locks, lights, windows, and even the remote start. My only problem is that when the car is running, I unlock the door, open it and the engine shuts off. How do I make it so that my car remains running when I open the door?

Connectez-vous pour répondre Voir 2 réponse(s)

29/12/2015

Nissan Bill W (1850Pts.)

0

Why is Evo-One turning headlights off then back on when ignition is turned off?

2007 Nissan Maxima w/Intellikey Evo-One is wired to driver door at the BCM to kill headlights when headlights are left on auto. Without this wired, the headlights stayed on. With it wired, I noticed that when I turn my ignition to off(after having had the car running), the Evo-one is turning my headlights off then back on really quickly. They still time out/turn off after the time passes though... I have HIDs so flicking my lights off then back on very quickly like this everytime I turn off my car isn't exactly ok... It does this everytime the car has been started as long as the Evo is plugged in. If I disconnect the Evo, my car no longer does this(lights stay on and time out properly without Evo plugged in). Install guide didn't say to use a diode on this...is that the issue? Or is this the Evo software? I need this to stop.

nissan

auto-off

headlights

Connectez-vous pour répondre Voir 2 réponse(s)

19/12/2015

Nissan Bill W (1850Pts.)

0

Rear defrost at temp control module latch or pulse?

I have the EVO-ONE set to trigger aux 1 at -5C(It is set to pulse for .5sec without disarming the alarm) in a 2007 Nissan Maxima. It is wired to the rear defroster wire at the temp control module connector(connector that plugs into what houses temp controls/defrost button). It isn't triggering rear defrost but it's just barely cold enough too. So a few questions... -Should I be latching instead for this car? I had a hard time finding the relay without somebody to press the defrost button so I went to the temp control module harness...didn't think it made a difference. -Where is the EVO-ONE getting its temp reading to decide if it's cold enough to trigger aux 1? Will it not do it if the car is warmed up already? If it's pulling from inside the car(ambient temp sensor), then this makes sense(inside the car would have to be -5C then). -What is "latch until shutdown" does it latch until you shut down the evo(as in take control of the car typically by pressing the brake) or until you shut off the car? -Why would you latch for only 10-30secs? Is this what required to trigger the relay for some cars?(kind of like if you had to hold the trunk release for 10-30secs to trigger the trunk) I'm just getting to testing this as it's just getting to 29F(-5C) here... I do realize my defrost light won't intially be on. However, when I turn the ignition to "run", the defrost light should be on if it was triggered(which is not happening). I have tested this theory by sitting in the car, remote starting it, pressing defrost(no light comes on), turn ignition of car to "run" (light comes on at ignition turn) to know this.

rear-defrost

nissan-maxima

Connectez-vous pour répondre Voir 1 réponse(s)

29/11/2015

Nissan Bill W (1850Pts.)

0

Can I trigger aux1(rear defrost) using the trunk release on my OEM key fob?

The yellow/black wire that comes from the 20pin connector on the EVO-ONE is labeld as "trunk release(output)" in the manual. This is the same wire I am suppose to use to trigger an auxillary accesory such as my rear defrost(which is what I wan to do). Does this mean I can use the trunk release button on my OEM fob to trigger the rear defrost? I'm hopping it will trigger the defrost if the car is running without opening my trunk and then go back to only opening my trunk when the car is off.

rear-defrost

trunk-release

Connectez-vous pour répondre Voir 1 réponse(s)

29/11/2015

Dodge Justin Pugh (230Pts.)

0

so i removed my evo chrt5 form my dodge avger

do i now have to get my key re programed car will not turn over

evo-chrt5

Connectez-vous pour répondre Voir 2 réponse(s)

29/11/2015

FAQ Noah Maas (250Pts.)

1

2-way Crimestopper kits or Fortin RFALL642W with the EVO-ALL?

I am trying to find a 2-way kit that will work with out much hassle. My EVO-ALL is already flashed for Crimestopper RF but I am unsure if the 2-way kits work. The REVO kits are all 1-way it seems. I also came across several Ebay listings for the Fortin RFALL642W which I am curious if that works out of the box or not. Trying my best to avoid buying a $50 flashing cable that I will use once. Any ideas?

rf-kits

rf-kit

Connectez-vous pour répondre Voir 1 réponse(s)

22/11/2015

Ram Kevin Miller (180Pts.)

0

I get to step 5 to insert key the light stays yellow doesn't turn red

i get all the way to step 5 where i have to insert the key then it should turn red but it doesnt it just stays yellow i when back to step 1 like it said and started over like 10 times still the same

evo-all

Connectez-vous pour répondre Voir 2 réponse(s)

22/11/2015

Nissan Bill W (1850Pts.)

0

what does option "35.2-Activate vehicle ignition at unlock" do?

Will option 35.2 on the remote starter settings for an EVO-ONE(reads as:Activate vehicle ignition at unlock) cause my car to try to start again while it's all ready running? I don't want to grind my starter just to find out(no anti-grind relay installed)... I am trying to unlock the ignition barrel on a 2007 nissan maxima w/intellikey while in idle mode. the intellikey works fine if i just remote start the car but if i kick it into idle mode then i have to unlock the ignition barrel with an actual key which is not cool. I am hoping this option will unlock the ignition barrel when i hit unlock on the doors(I realize the safety issue associated with my igntion barrel unlocking with no key in place).

activate-vehicle-ignition-at-unlock

Connectez-vous pour répondre Voir 1 réponse(s)

22/11/2015

Nissan Bill W (1850Pts.)

0

Why won't my Intellikey unlock ignition barrel after entering "idle mode"? Have to use real key...

I have an EVO-ONE installed and working in my 2007 Nissan Maxima w/Intellikey. I use my OEM fob/Intellikey to start the car(3x lock). I can then hop into my car and turn the ignition barrel to the run position with my Intellikey in my pocket still and drive away. When I park the car with it still running, I can hit the lock button 3x on my fob/Intellikey and the car will enter "idle mode". I can turn the ignition barrel to the "off" position and the car will remain running in idle mode. The problem I'm having is after entering "idle mode", I can not turn my ignition barrel back to "run" so that I can drive away without using an actual physical key! Why can I not take control of the car with my Intellikey while in "Idle mode"? The Intellikey still works on the doors while in "idle mode"(I know this because my door handle has a button I can press to unlock if the Intellikey is in range); it just won't let me move the ignition barrel. I have tried walking away from the car out of the Intellikey's range...I'm at a loss and really need this working. Without it, I have purchased and installed an expensive paperweight. EDIT:What about option 35 in the starter settings? It's "Door unlock special application". what would enabling "Activate vehicle ignition at unlock" do? will it try to start everytime i unlock my door then or will it just unlock my igntion barrel like i want it to? EDIT2:I just downgraded from EVO firmware 7.19 back to 7.18 with the same results. When in "idle mode", if I kill the starter via the brake pedal, I can instantly turn the ignition barrel to "run" using the Intellikey(no physical key in the ignition barrel). It simply won't turn the ignition barrel in "idle mode". I'm thinking this is firmware issue with the EVO-ONE.

intellikey

idle-mode

Connectez-vous pour répondre Voir 1 réponse(s)

21/11/2015

FAQ Bob Daley (350Pts.)

1

Car won't start after installing EVO-ALL - 2008 G35

Hi guys, I just installed the EVO ALL with T-Harness into a 2008 PTS Infiniti G35. It wouldn't start the car after installation so I reset the unit and reflashed and now the LEDs respond differently (blue flashes on unlock, red and yellow come on then red and blue if i recall). The car won't crank though. Any ideas? service #001A06 556476 I verified continuity to the brown wire on the start button. I'm at a loss. Thanks! Bob **edit** so i went back and apparently the 08 g35 isn't compatible with the lock lock lock feature but the literature didn't seem entirely clear that it wasn't so in the end I need to install the DSM300 telematics unit, which is fine since I have it sitting here already. The weird thing is that the blue light flashes when I lock the door so clearly the unit sees the door lock get pinged from the CANBUS. Does anyone know why the 3x lock doesn't it work?

standalone-g35

Connectez-vous pour répondre Voir 3 réponse(s)

21/11/2015

FAQ Bill W (1850Pts.)

0

Can I program the EVO-ONE with it hooked up to the car if I disconnect the car's battery first?

I really don't want to remove the EVO-ONE that I installed in my 2007 Nissan Maxima w/Intellikey just to program it again(I just want to turn on "unlock doors when ignition is turned off") and if I could leave all the harnesses attached too, that'd be great. So my question is: Can I program the EVO-ONE with it installed in the car(all harnesses attached) with the FlashLInk 2 if I disconnect the car's battery first? Or do I HAVE to disconnect all the harnesses from the EVO-ONE before programming?

program-harness-attached

Connectez-vous pour répondre Voir 1 réponse(s)

20/11/2015

Nissan Bill W (1850Pts.)

1

Does 2007 Nissan Maxima need the tach wire ran to the ECU/ECM to use "Tach Datalink only" on EVO-ONE?

I installed an EVO-ONE using the THAR-ONE-NIS2 T-harness in a 2007 Nissan Maxima w/Intellikey (obviously more connections were needed aside from the T-harness)... My question is: Do I need to run the tachometer wire from the Fortin 20pin connector to the tachometer wire at the ECU/ECM in order to use the "Tach Datalink only" option that's under the remote starter options via the FlashLink software. I thought some cars are getting this signal via the OBDII CANs. My Fortin install instrustions (Guide #17763) only had me connect to CAN-high and CAN-low on the OBDII connector. I already set the datalink protocol to "Fortin" as I thought this would be required. I realize I could just use "tachless" mode but I would prefer it starting using my tach signal. Tachless mode does work though(I used this mode to verify the bypass and remote start features were working). To be clear, I have only tried starting the car with "tachless only" mode and i have not ran a wire to the ECU/ECM tach line yet as im not sure if it is needed. So what do I need to do in order to use "Tach datalink only" mode? My guess is setting datalink protocol to "Fortin" and run the evo's tach wire to the tach wire @ the ECM.

nissan-maxima-tach

Connectez-vous pour répondre Voir 2 réponse(s)

01/11/2015

Ram Chris Chicoine (130Pts.)

0

After I remote start and drive my truck, I have to use the remote to stop it, why?

I have my EVO combo and CHRT4 hooked up as a stand alone remote start using the t harness. It starts and runs great. Tonight, I started the truck with the OEM remote, put my key in the ignition, turned the key to the run position, and drove home. When I got there, I took the key out of the ignition and the truck would not shut off. I had to use the remote to shut it off. I've installed other remote starts on different vehicles and they all used the brake wire to change from the remote start to the OEM ignition..if that makes sense to anyone. And the key would shut off the vehicle once it was removed. Did I not wire this up correctly in my 2012 Ram Diesel or is this just the way this system works? Thank you for your help

Connectez-vous pour répondre Voir 4 réponse(s)

05/02/2015

Dodge Dwight Smith (350Pts.)

0

Is it possible to remove key from ignition and vehicle continues to run.

Does this system allow me to leave the vehicle running, but take my keys with me? All without shutting the vehicle off and then restarting it with the remote start.

dodge-ram

evo-all

idle-mode

Connectez-vous pour répondre Voir 2 réponse(s)

CATÉGORIES DE PRODUITS

CONTRÔLE À DISTANCE & SUIVI

POUR L'INSTALLATEUR

DÉMARRAGE À DISTANCE ET ALARME

Contrôles à distance et applications pour la gestion de flotte

Modules de contrôle à distance et de contournement de clé à puce

Ensembles de type tout-en-un

Ensembles EVO-RS avec harnais en T inclus

Accessoires d'installation

Câble de type harnais en T

Outils d'installation et de programmation

EVO-GEAR

Produits discontinués

Voir tout les produits

Audi

Chevrolet

Ford

GMC

Honda

Hyundai

Kia

Mazda

Nissan

RAM

Subaru

Toyota

Volkswagen

Voir toutes les solutions

Audi

Chevrolet

Ford

GMC

Honda

Hyundai

Kia

Mazda

Nissan

RAM

Subaru

Toyota

Volkswagen

Voir les solutions

EVO-START LTE — Découvrez le plein contrôle mobile

EVO-START LTE — Sécuriez et protégez vos actifs mobiles

EVO-START LTE — Suivi GPS et gestion de flotte

EVO-9-SERIES — Contrôlez à distance avec style

EVO-4-SERIES — La meilleure valeur sur le marché

Harnais en T — Facilitez, accélérez et sécurisez vos branchements

Voir toutes les ressources

Application de programmation FlashLink Mobile

Application de programmation FlashLink Manager

Contrôleurs à distance compatibles

Questions et réponses

Guides de dépannage

Galerie vidéos

Voir tous les outils de soutien

Trouver nos produits et planifier une installation

Commander nos produits en ligne

Trouver un distributeur autorisé

Voir tout

À propos

Pourquoi choisir Fortin

Carrières

Contactez-nous

Utilisateur

Activité récente

Questions demandée(s)

12

Question(s) répondue(s)

11

Vous cherchez nos meilleurs participants ?

Vous n'avez pas trouvé ce que vous cherchiez ?

EVO-ONE is preventing my physical key from starting my car.

Evo-One responds to commands over Fortin RF642W kit poorely.

What Extra wires no need to be connected (Mandatory)? FORD EDGE 2013

Wired exactly as the install guide said but car won't even try to crank.

Does the Evo-One work as a remote starter for a 2003 Buick Century?

Does Evo-One starter firmware .51 have all the improvements that firmware 1.18 brought?

Having being remote started stops responding to remote unless really near by the car

Car Shutoff after 15 minutes - even when driving

Voir
les solutions